JVC G2000 manual Basic Operations, Turning on the Power, Turn on the Main Power switch

Page 28

Basic Operations

■Projector’s buttons

STAND BY	STAND BY indicator
	OPERATE indicator
LAMP	OPERATE button
TEMP	2, 1
TEMP
EMERGENCY
VIDEO	MAIN POWER switch 1, 2
COMPUTER

SETTING

+3

QUICK

ALIGN

-2

■Remote control unit

The following describes the basic procedure for normal use of the projector.

1.Turning on the Power

1 Turn on the MAIN POWER switch.

ON [ ❙ ]:The main power turns on and the STAND BY indicator comes on.

Projector’s indicator

STAND BY

(ON)

2Press the OPERATE button for one second or more.

•The OPERATE indicator comes on.

•About 30 seconds after the MAIN POWER switch is turned on, you can start projecting.

	Projector
Remote control unit
OPERATE	(ON)
or	OPERATE

Notes

•After the power is turned on, the screen may be jumbled for a few seconds, but this is not a malfunction.

•If the light-source lamp does not light up, try to press the OPERATE button for more than a second again.

■Turning off the Power

1Press the OPERATE button for one second or more.

•The STAND BY indicator changes to blinking, and the projector goes into cool-down mode.

Example of the projector’s button

Projector

(Blinking)

OPERATE	COMPUTER	VIDEO
	T
VOL.	ZOOM	FOCUS
	W
PAGE	MENU/ENTER
PAGE
BACK
PRESET
QUICK		AV
ALIGN.		MUTING

Touche OPERATE

2, 1

(ON)	\
OPERATE	\	STAND BY
OPERATE

2Turn off the MAIN POWER switch after the STAND BY indicator

changes to steady on.

OFF [à]: The MAIN POWER switch turns off and the STAND BY indicator goes off.

Projector

(OFF)

STAND BY

*Do not turn off the MAIN POWER switch during cool down mode (the STAND BY indicator blinking). Turn it off after the STAND BY indicator becomes on (stand- by mode).

26

G2000 p.24-34

26

99.11.20, 3:28 AM

Image 28

Contents Pour l’utilisateur For customer UseModel No No de modèle G2000 Serial No No de série G2000 CoverA4 99.11.19, 1042 PM G2000 Safety Precautions About burning-in of the D-ILA deviceSafety Precautions Lighters that present special hazards when over heatedLamp is turned on. Exposure of your eyes to the strong Xenon gas is enclosed with high pressure inside the lightContents Accessories Controls and Features Front Side / Top Surface / Right SideConnector panel How to extend the adjustable foot on the rearLeft-hand side Control panelBottom Surface Air intake area filterOpening for replacing the light-source lamp Fixing foot Position selecting screw for ceiling mountingControl Panel Setting button When a menu is shownVideo button Computer buttonConnector Panel C S video input terminal Mini DIN 4 pinRS-232C terminal D-sub 9 pin Computer OUT computer output terminal D-sub 3-row 15 pinInput of external sync signals is automatically detected Audio input terminal stereo mini jackRow 15 pin Audio audio input terminal stereo mini jackRemote Control Unit Installing Batteries Install the batteriesPrecautions for using batteries Open the back coverInstalling the Projector Precautions for InstallationDo not install the projector in the following places When installing the projector, observe the followingsProjection Distance and Screen Size Projection screen size diagonal lengthCenter line of the lens Projection55.76 ft 17.0 m 294 Approx cm 443 59.04 ft 18.0 m 311 Approx cm 46962.32 ft 19.0 m 328 Approx cm 495 65.6 ft 20.0 m 345 Approx cm 521Setting the position selecting screw for Ceiling Mounting Effective Range and Distance of the Remote Control UnitEffective range and distance of the remote control unit Connecting to Various Devices Signals that Can Be Input to the ProjectorVideo signals Computer signalsConnecting to Video Devices Connecting to Hi-Vision DevicesVideo devices Hi-Vision devicesConnecting to Other Devices Connecting to Devices which Control the ProjectorDesktop type Game device, etcConnecting to Computer Devices Connection to an IBM PC or IBM-compatible computerRead the manual which comes with each device thoroughly RGB output devicesConnection to Macintosh To monitor connector SuppliedPersonal computer connection cable Connecting the Power Cord Supplied To use the projectorRemove the lens cap To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Turning on the Power Turn on the Main Power switchBasic Operations Press the Operate button for one second or moreAdjust the screen size Switch the inputWhen you press Video When you press ComputerAdjust focus Adjust sound volumeAdjust focus with the remote control’s Focus + ButtonsTo turn off video image and audio sound temporarily To use the quick alignment functionProjector’s button Press onceTo display the Setting menu To use the remote control’s Preset buttonValues, press the remote control’s Preset button Projector buttonTo display Channel Back buttonOperating the Setting Menu Making Basic SettingsPress the Setting button of the projector Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Changing the Color System Select Decoder with the cursor button 5 orSet the color system with the cursor button 2 or To finish the main menu, press the page Back buttonChanging the Language Display Select Language with the cursor button 5 orSet the desired language with the cursor button 2 or ButtonAdjusting the Pixel Clock Adjust Tracking and Phase with the cursor buttonsSelect Pixel Clock with the cursor button 5 or Main menu appears on the screenAdjust H. POS. and V. POS. with the cursor buttons Adjusting the Screen PositionSelect Position with the cursor button 5 or Adjusting Picture Quality Select the item to adjust with the cursor button 5 orWhen AV signals are input When computer-related signals are inputSubmenu items For video system inputFor computer system input Picture menuSets a mode which allows easy Adjustment values 0, text30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lower 30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddishAdjusting Sound Quality Adjust Treble and Bass with the cursor buttonsSelect the Sound with the cursor Button 5 orSetting and Adjusting Other Functions Options Select the item to set adjust with the cursor button 5 orFollowing optional functions can be set adjusted Select the Options with the cursor button 5 orSet adjust the desired item with the cursor button 2 or Options menuAspect Changing Setting the Source Select a submenu item Source using the cursor button 5 orSelect the item to set using the cursor buttons 5/ or 2/3 Source item displayed in text is indicated in magenta colorWhen Auto is selected When a dedicated source mode is selectedWhen User is selected Fix itSetting Up Channels Channel Setup menuSelect the Channel with the cursor button 5 or Submenu item ChannelTo delete the contents of the channel registered set up FixPress the cursor button 5or to select a Line item Press the MENU/ENTER button to set fixChannel setup menu Source Setup menu is displayed on the screenIf any Line item is not registered, you cannot choose a SOURCE’ or SWNo item. First register a Line itemPress the MENU/ENTER button to set To set up a switcher number SWNo Press the cursor button 3 to move to SWNoPress the cursor button 2or 3to select a number Press the page Back buttonPress the page Back when no menu is displayed To changing channels using a Direct ChannelChanging Channels Select the Channel number with the cursor button 5 orSelected CH is shown in magenta color Channel Setup/Selection menuSubmenu item Channel Source Setting up or Change User Sources Press the cursor button 5 or to select User Source SetupBefore setting up a user source Submenu item User Source SetupPress the cousor button 3 to move to User Name User Name Setup menu To delete user namesOverwrite the user name with spaces Up to 9 input positions can be selectedSetting up or Changing the Display Size Press the cursor button 5or to select an item to adjustPress the cursor button 2or 3to make adjustments Press the cursor button 5or to select Display SizePlace the main power switch to the OFF à position Replacing the FuseLoosenit. the fuse holder to remove Fuse 15A Fuse holderRemove the lamp-replacement Replacing the Light-Source LampOpening cover by Loosening Screws Loosen the two screws with a flat-end screwdriverInsert the new lamp unit fully inside and fasten the screws Fasten the two screws with a flat-end screwdriverResetting the Lamp Use Time Turn on the Main Power switch to go into stand-by modeThis completes the resetting of the lamp use time Projector’s buttonCleaning and Replacing the Filter Clean the filterReinstall the filter Fasten the screw with a flat-end screwdriverTroubleshooting When the emergency indicator starts blinking MaintenanceAV in AV in input SpecificationsComputer in Computer input Other Outside dimensions DTV-format signalsTop FrontPin assignment Specifications for terminals TerminalRS-232C terminal Computer IN-1 PC / Computer OUT TerminalG2000 CoverA4 99.11.19, 1042 PM Hughes-JVC Technology Corporation