JVC G2000 manual Projection Distance and Screen Size, Projection screen size diagonal length

Page 18

Installing the Projector (Cont.)

Projection Distance and Screen Size

The projector’s projection lens is a zoom lens of about 1.5 x. The screen size at the maximum enlargement is 1.5 times that of the minimum size.

The projection distance that can be focused is 2.5 to 20 m. Install the projector within this range.

Screen

Change of projection screen

according to aspect ratio

 

 

Screen with 4 : 3 aspect ratio

Screen with 16 : 9 aspect ratio

90°

90°

90°

Center line of the lens

Install the projector so the lower edge of the projection screen is at the same height as the lens’ center line.

Projection

 

Projection screen size (diagonal length)

 

When screen aspect ratio is 4 : 3

When screen aspect ratio is 16 : 9

distance

Minimum projection screen

Maximum projection screen

Minimum projection screen

Maximum projection screen

 

8.2 ft

42”

63”

39”

57”

(2.5 m)

(approx. 107 cm)

(approx. 160 cm)

(approx. 100 cm)

(approx. 144 cm)

 

 

 

 

 

16.4 ft

86”

128”

79”

117”

(5 m)

(approx. 219 cm)

(approx. 325 cm)

(approx. 201 cm)

(approx. 297 cm)

 

 

 

 

 

32.8 ft

172”

259”

158”

237”

(10 m)

(approx. 437 cm)

(approx. 657 cm)

(approx. 402 cm)

(approx. 601 cm)

 

 

 

 

 

65.6 ft

345”

521”

317”

478”

(20 m)

(approx. 877 cm)

(approx. 1,323 cm)

(approx. 806 cm)

(approx. 1,214 cm)

 

 

 

 

 

*Also, refer to the table of “Relationship Between Projection Distances and Projection Screen Sizes” on page 17 as a reference.

CAUTIONS and NOTES

Install the screen so the lower edge of the projected picture aligns with the extended center line of the projector’s lens. That way, the lower edge of the picture projected on a 4 : 3 aspect ratio screen aligns with the extended center line of the lens. Also, the screen must be at right angles with the extended center line of the lens (so that projection occurs at right angles with the screen).

When installing the screen, use a 4 : 3 aspect ratio picture.

(A 16 : 9 aspect ratio picture is projected based on the width of the range in which a 4 : 3 aspect ratio picture is projected.)

The diagonal length of a 16 : 9 aspect ratio picture is about 91.8% that of a 4 : 3 aspect ratio picture. This value is a guide and should be used as a reference.

When projecting at the maximum projection distance (20 m/65.6 ft), we recommend that the projector be used with the zoom on the Tele (T).

If sunlight or lamp light strikes the projection screen directly, the picture becomes whitish and dim. Be sure to use a curtain, etc. to shield the light.

Trapezoidal distortion may not be corrected.

Adjust the projector within the range of angle adjustment (up/down adjustment angle: +7°; horizontal adjustment angle: ±1.5°) so that it is set up level.

The numeric values listed in the table of Relationship between Projection Distances and Screen Sizes on page 17 are provided only as a guide or reference. The projection sizes may vary within manufacturing tolerances of the projection lens.

When hanging the projector from the ceiling, use a dedicated hanging fixture.

16

G2000 p.15-23

16

99.11.20, 3:28 AM

Image 18
Contents For customer Use Pour l’utilisateurModel No No de modèle G2000 Serial No No de série G2000 CoverA4 99.11.19, 1042 PM G2000 Safety Precautions About burning-in of the D-ILA deviceLamp is turned on. Exposure of your eyes to the strong Safety PrecautionsLighters that present special hazards when over heated Xenon gas is enclosed with high pressure inside the lightContents Accessories Controls and Features Front Side / Top Surface / Right SideLeft-hand side Connector panelHow to extend the adjustable foot on the rear Control panelOpening for replacing the light-source lamp Bottom SurfaceAir intake area filter Fixing foot Position selecting screw for ceiling mountingControl Panel Video button Setting buttonWhen a menu is shown Computer buttonRS-232C terminal D-sub 9 pin Connector PanelC S video input terminal Mini DIN 4 pin Computer OUT computer output terminal D-sub 3-row 15 pinRow 15 pin Input of external sync signals is automatically detectedAudio input terminal stereo mini jack Audio audio input terminal stereo mini jackRemote Control Unit Precautions for using batteries Installing BatteriesInstall the batteries Open the back coverDo not install the projector in the following places Installing the ProjectorPrecautions for Installation When installing the projector, observe the followingsCenter line of the lens Projection Distance and Screen SizeProjection screen size diagonal length Projection62.32 ft 19.0 m 328 Approx cm 495 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 65.6 ft 20.0 m 345 Approx cm 521Effective Range and Distance of the Remote Control Unit Setting the position selecting screw for Ceiling MountingEffective range and distance of the remote control unit Video signals Connecting to Various DevicesSignals that Can Be Input to the Projector Computer signalsVideo devices Connecting to Video DevicesConnecting to Hi-Vision Devices Hi-Vision devicesDesktop type Connecting to Other DevicesConnecting to Devices which Control the Projector Game device, etcRead the manual which comes with each device thoroughly Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer RGB output devicesTo monitor connector Supplied Connection to MacintoshPersonal computer connection cable Remove the lens cap Connecting the Power Cord SuppliedTo use the projector To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Basic Operations Turning on the PowerTurn on the Main Power switch Press the Operate button for one second or moreWhen you press Video Adjust the screen sizeSwitch the input When you press ComputerAdjust focus with the remote control’s Focus + Adjust focusAdjust sound volume ButtonsProjector’s button To turn off video image and audio sound temporarilyTo use the quick alignment function Press onceValues, press the remote control’s Preset button To display the Setting menuTo use the remote control’s Preset button Projector buttonTo display Channel Back buttonPress the Setting button of the projector Operating the Setting MenuMaking Basic Settings Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Set the color system with the cursor button 2 or Changing the Color SystemSelect Decoder with the cursor button 5 or To finish the main menu, press the page Back buttonSet the desired language with the cursor button 2 or Changing the Language DisplaySelect Language with the cursor button 5 or ButtonSelect Pixel Clock with the cursor button 5 or Adjusting the Pixel ClockAdjust Tracking and Phase with the cursor buttons Main menu appears on the screenAdjusting the Screen Position Adjust H. POS. and V. POS. with the cursor buttonsSelect Position with the cursor button 5 or When AV signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or When computer-related signals are inputFor computer system input Submenu itemsFor video system input Picture menu30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lower Sets a mode which allows easyAdjustment values 0, text 30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddishSelect the Sound with the cursor Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Button 5 orFollowing optional functions can be set adjusted Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or Select the Options with the cursor button 5 orSet adjust the desired item with the cursor button 2 or Options menuAspect Select the item to set using the cursor buttons 5/ or 2/3 Changing Setting the SourceSelect a submenu item Source using the cursor button 5 or Source item displayed in text is indicated in magenta colorWhen User is selected When Auto is selectedWhen a dedicated source mode is selected Fix itSelect the Channel with the cursor button 5 or Setting Up ChannelsChannel Setup menu Submenu item ChannelPress the cursor button 5or to select a Line item To delete the contents of the channel registered set upFix Press the MENU/ENTER button to set fixIf any Line item is not registered, you cannot choose a Channel setup menuSource Setup menu is displayed on the screen SOURCE’ or SWNo item. First register a Line itemPress the MENU/ENTER button to set Press the cursor button 2or 3to select a number To set up a switcher number SWNoPress the cursor button 3 to move to SWNo Press the page Back buttonChanging Channels Press the page Back when no menu is displayedTo changing channels using a Direct Channel Select the Channel number with the cursor button 5 orChannel Setup/Selection menu Selected CH is shown in magenta colorSubmenu item Channel Source Before setting up a user source Setting up or Change User SourcesPress the cursor button 5 or to select User Source Setup Submenu item User Source SetupPress the cousor button 3 to move to User Name Overwrite the user name with spaces User Name Setup menuTo delete user names Up to 9 input positions can be selectedPress the cursor button 2or 3to make adjustments Setting up or Changing the Display SizePress the cursor button 5or to select an item to adjust Press the cursor button 5or to select Display SizeLoosenit. the fuse holder to remove Place the main power switch to the OFF à positionReplacing the Fuse Fuse 15A Fuse holderOpening cover by Loosening Screws Remove the lamp-replacementReplacing the Light-Source Lamp Loosen the two screws with a flat-end screwdriverInsert the new lamp unit fully inside and fasten the screws Fasten the two screws with a flat-end screwdriverThis completes the resetting of the lamp use time Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode Projector’s buttonReinstall the filter Cleaning and Replacing the FilterClean the filter Fasten the screw with a flat-end screwdriverTroubleshooting When the emergency indicator starts blinking MaintenanceSpecifications AV in AV in inputComputer in Computer input Other Top Outside dimensionsDTV-format signals FrontRS-232C terminal Pin assignment Specifications for terminalsTerminal Computer IN-1 PC / Computer OUT TerminalG2000 CoverA4 99.11.19, 1042 PM Hughes-JVC Technology Corporation