JVC G2000 manual Controls and Features, Front Side / Top Surface / Right Side

Page 8

Controls and Features

Front Side / Top Surface / Right Side

q

p

9

1

8 7

6

5 4 3

2

1 Exhaust vents		6 Adjustable foot (for horizontal angle adjustment)
Vents for cooling fans through which warm air comes out.		By extending the feet, the projector angle can be adjusted
		up to +7°.

CAUTION

•Do not block the exhaust vents, or heat builds up inside, possibly causing a fire. Also, do not touch the vents, or this could cause a low-temperature burn.

2Carrying handle

Raise this handle when carrying the projector.

CAUTIONS

• When carrying the projector, do not give a shock to it. Be

careful to keep its balance.

•Extending the front adjustable foot

While pushing the lever, raise the projector, and the adjustable foot extends

+7°

lever

• Do not carry it while the light source lamp is on or the cooling

fan is operating. This could cause personal injury.

How to use the carrying handle

Carrying handle

3AC IN (power input) terminal

This is the power input terminal where the supplied power cord is connected. For details, refer to page 24.

4Fuse holder

A fuse rated 15A/250V is installed. (Power source protection)

To replace the fuse, use a fuse with the same specifications.

5MAIN POWER switch

This is the main power switch. When it is turned on, the projector goes into stand-by state, and the STAND BY indicator on the control panel comes on.

ON [ ❙ ]: The main power turns on.

OFF [à]: The main power turns off.

automatically. To retract the foot, pushing the lever , lower the projector slowly;

the projector is fixed at the position where you release the lever.

7Built-in speaker (left)

8Built-in speaker (right)

9Lens

Projection lens, which is an electrically driven, approx. 1.5 x zoom lens. Before projection, remove the lens cap.

pLens cap

The cap has a string attached and the string is fixed to the projector when shipped from the factory. It is recommended that the cap be fitted on to prevent the lens becoming dirty when the projector is not used.

qRemote sensor

When operating with the remote control, aim it toward this sensor. You can also operate the remote control by pointing it to a screen and allowing the remote sensor to receive the reflected light.

6

G2000 p.05-14

6

99.11.20, 3:28 AM

Image 8

Contents Model No No de modèle G2000 Serial No No de série For customer UsePour l’utilisateur G2000 CoverA4 99.11.19, 1042 PM G2000 Safety Precautions About burning-in of the D-ILA deviceSafety Precautions Lighters that present special hazards when over heatedLamp is turned on. Exposure of your eyes to the strong Xenon gas is enclosed with high pressure inside the lightContents Accessories Controls and Features Front Side / Top Surface / Right SideConnector panel How to extend the adjustable foot on the rearLeft-hand side Control panelBottom Surface Air intake area filterOpening for replacing the light-source lamp Fixing foot Position selecting screw for ceiling mountingControl Panel Setting button When a menu is shownVideo button Computer buttonConnector Panel C S video input terminal Mini DIN 4 pinRS-232C terminal D-sub 9 pin Computer OUT computer output terminal D-sub 3-row 15 pinInput of external sync signals is automatically detected Audio input terminal stereo mini jackRow 15 pin Audio audio input terminal stereo mini jackRemote Control Unit Installing Batteries Install the batteriesPrecautions for using batteries Open the back coverInstalling the Projector Precautions for InstallationDo not install the projector in the following places When installing the projector, observe the followingsProjection Distance and Screen Size Projection screen size diagonal lengthCenter line of the lens Projection55.76 ft 17.0 m 294 Approx cm 443 59.04 ft 18.0 m 311 Approx cm 46962.32 ft 19.0 m 328 Approx cm 495 65.6 ft 20.0 m 345 Approx cm 521Effective range and distance of the remote control unit Effective Range and Distance of the Remote Control UnitSetting the position selecting screw for Ceiling Mounting Connecting to Various Devices Signals that Can Be Input to the ProjectorVideo signals Computer signalsConnecting to Video Devices Connecting to Hi-Vision DevicesVideo devices Hi-Vision devicesConnecting to Other Devices Connecting to Devices which Control the ProjectorDesktop type Game device, etcConnecting to Computer Devices Connection to an IBM PC or IBM-compatible computerRead the manual which comes with each device thoroughly RGB output devicesPersonal computer connection cable To monitor connector SuppliedConnection to Macintosh Connecting the Power Cord Supplied To use the projectorRemove the lens cap To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Turning on the Power Turn on the Main Power switchBasic Operations Press the Operate button for one second or moreAdjust the screen size Switch the inputWhen you press Video When you press ComputerAdjust focus Adjust sound volumeAdjust focus with the remote control’s Focus + ButtonsTo turn off video image and audio sound temporarily To use the quick alignment functionProjector’s button Press onceTo display the Setting menu To use the remote control’s Preset buttonValues, press the remote control’s Preset button Projector buttonTo display Channel Back buttonOperating the Setting Menu Making Basic SettingsPress the Setting button of the projector Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Changing the Color System Select Decoder with the cursor button 5 orSet the color system with the cursor button 2 or To finish the main menu, press the page Back buttonChanging the Language Display Select Language with the cursor button 5 orSet the desired language with the cursor button 2 or ButtonAdjusting the Pixel Clock Adjust Tracking and Phase with the cursor buttonsSelect Pixel Clock with the cursor button 5 or Main menu appears on the screenSelect Position with the cursor button 5 or Adjusting the Screen PositionAdjust H. POS. and V. POS. with the cursor buttons Adjusting Picture Quality Select the item to adjust with the cursor button 5 orWhen AV signals are input When computer-related signals are inputSubmenu items For video system inputFor computer system input Picture menuSets a mode which allows easy Adjustment values 0, text30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lower 30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddishAdjusting Sound Quality Adjust Treble and Bass with the cursor buttonsSelect the Sound with the cursor Button 5 orSetting and Adjusting Other Functions Options Select the item to set adjust with the cursor button 5 orFollowing optional functions can be set adjusted Select the Options with the cursor button 5 orSet adjust the desired item with the cursor button 2 or Options menuAspect Changing Setting the Source Select a submenu item Source using the cursor button 5 orSelect the item to set using the cursor buttons 5/ or 2/3 Source item displayed in text is indicated in magenta colorWhen Auto is selected When a dedicated source mode is selectedWhen User is selected Fix itSetting Up Channels Channel Setup menuSelect the Channel with the cursor button 5 or Submenu item ChannelTo delete the contents of the channel registered set up FixPress the cursor button 5or to select a Line item Press the MENU/ENTER button to set fixChannel setup menu Source Setup menu is displayed on the screenIf any Line item is not registered, you cannot choose a SOURCE’ or SWNo item. First register a Line itemPress the MENU/ENTER button to set To set up a switcher number SWNo Press the cursor button 3 to move to SWNoPress the cursor button 2or 3to select a number Press the page Back buttonPress the page Back when no menu is displayed To changing channels using a Direct ChannelChanging Channels Select the Channel number with the cursor button 5 orSubmenu item Channel Source Channel Setup/Selection menuSelected CH is shown in magenta color Setting up or Change User Sources Press the cursor button 5 or to select User Source SetupBefore setting up a user source Submenu item User Source SetupPress the cousor button 3 to move to User Name User Name Setup menu To delete user namesOverwrite the user name with spaces Up to 9 input positions can be selectedSetting up or Changing the Display Size Press the cursor button 5or to select an item to adjustPress the cursor button 2or 3to make adjustments Press the cursor button 5or to select Display SizePlace the main power switch to the OFF à position Replacing the FuseLoosenit. the fuse holder to remove Fuse 15A Fuse holderRemove the lamp-replacement Replacing the Light-Source LampOpening cover by Loosening Screws Loosen the two screws with a flat-end screwdriverInsert the new lamp unit fully inside and fasten the screws Fasten the two screws with a flat-end screwdriverResetting the Lamp Use Time Turn on the Main Power switch to go into stand-by modeThis completes the resetting of the lamp use time Projector’s buttonCleaning and Replacing the Filter Clean the filterReinstall the filter Fasten the screw with a flat-end screwdriverTroubleshooting When the emergency indicator starts blinking MaintenanceComputer in Computer input SpecificationsAV in AV in input Other Outside dimensions DTV-format signalsTop FrontPin assignment Specifications for terminals TerminalRS-232C terminal Computer IN-1 PC / Computer OUT TerminalG2000 CoverA4 99.11.19, 1042 PM Hughes-JVC Technology Corporation