Elmo CRP-26 owner manual Appendix

Page 64

Appendix

No image

– Check the connection between your computer or video equipment

 

and the projector. See pages 14-16.

 

– See if the input signal is correctly output from your computer. Some

 

laptop computers may need to change the setting for monitor output

 

when connecting to a projector. See your computer’s instruction

 

manual for the setting.

 

– It takes about 30 seconds to display an image after turning on the

 

projector. See page 18.

 

– Check the Input signal, color system, video system or computer

 

system mode.

 

– Make sure the temperature is not out of the specified Operating

 

Temperature (41˚F–95˚F [5˚C–35˚C]).

 

– When No Show is operating, the image cannot be displayed. Press

 

the NO SHOW button or any other button on the remote control.

 

 

No sound

– Check the audio cable connection from audio input source.

 

– Adjust the audio source.

 

– Press the Volume + button. See page 24.

 

– Press the Mute button. See page 24.

 

– When the AUDIO OUT is plugged-in, the projector's built-in speaker

 

is not available.

 

– Is the image projected? You will hear the sound only when the image

 

is projected.

 

 

The color is strange.

– Check the Input signal, color system,video system or computer

 

system mode.

 

– Make sure the Blackboard is not selected on Image select

 

menu. See pages 32, 39.

Some displays are not seen during the operation.

– Check the Display function. See page 45.

Auto PC adjustment function

– Check the Input signal. Auto PC adjustment function can not work

does not work.

when 480p,575p.720p,480i,575i,1035i or 1080i is selected. See

 

page 29.

The setting does not remain after turning off power.

Make sure you selected Store after adjusting setting. Some settings can not be stored if not registered with Store. See pages 34, 41.

Power management does not

– Power management function can not work while Freeze or No

work.

Show function is running. See page 50.

 

 

Capture function does not work.

– Check the connection and the input signal to see if there is signal.

 

 

Auto setup does not work properly.

– Make sure Off is not selected at any function of Auto setup. See page

 

44.

 

– Make sure On is not selected at the Ceiling function. See page 49.

Auto keystone function does not work even when the projector is tipped.

Make sure the Auto keystone function is not set to Manual. Press the AUTO SETUP button on the top control. See pages 23, 44.

64

Image 64
Contents CRP-22 CRP-26 Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector AC Power Cord Requirement AC Power Cord for the United States and CanadaAC Power Cord for the United Kingdom ComplianceFront Back Part Names and FunctionsBottom ⑥ LAN Connection Terminal Part Names and Functions Rear Terminal⑧ DC OUT 12V 1.1A Part Names and Functions Top Control Part Names and Functions Remote Control ① ON/STAND-BY buttonRemote Control Operating Range Remote Control CodeAdjustable Foot InstallationPositioning the Projector Installation Connecting to a Computer Cables used for connectionInstallation Connecting to Video Equipment Computer in 1/ S-VIDEO in / Component Installation Connecting the AC Power Cord NoteBasic Operation Turning On the ProjectorWhat is PIN code? Basic OperationEnter a PIN code PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Basic Operation How to Operate the On-Screen Menu Remote ControlTop Control On-Screen MenuBasic Operation Menu Bar For detailed functions of each menu, see Menu Tree on pagesBasic Operation Zoom and Focus Adjustment Auto Setup FunctionKeystone Correction NotesDirect Operation Basic Operation Sound AdjustmentMenu Operation Basic Operation Remote Control Operation Timer button No Show buttonImage button Screen buttonInput Source Selection RGB Computer 1/Computer Computer InputInput Menu Selecting Computer System Manually Computer Input Computer System SelectionPC System Menu Computer Input Auto PC Adjustment PC adjust MenuTo store adjustment parameters Auto PC adjComputer Input Manual PC Adjustment Reset Mode freeComputer Input StoreComputer Input Image Mode Selection Image select MenuComputer Input Image Adjustment Image Adjust MenuScreen Size Adjustment Screen MenuCustom Position H/VFor zooming in and out the images Digital zoom + Digital zoomVideo Input Input Source Selection Video, S-videoVideo Input MenuComponent RGB ScartVideo Input Video System Selection Video or S-videoAV System Menu Video or S-video Component AV System Menu ComponentVideo Input Image Mode Selection CinemaColor Video Input Image AdjustmentTint Off Disabled Lower reduction Higher reduction Progressive Video InputStore Menu Noise reductionVideo Input Screen Size Adjustment Setting SettingSetting Menu Language LanguageAuto setup Auto setupInput search Auto KeystonePower off? p.20 KeystoneBackground UserShow the image you captured Capture Logo PIN code lockCapture Logo PIN code lockEnter a Logo PIN code Change the Logo PIN code lock settingLogo PIN code change Ceiling RearTerminal ComputerShut down Power managementOn start Standby mode Closed CaptionLamp life control Remote control Lamp controlKey lock PIN code lock Security Key lock and PIN code lockKey lock PIN code lockChange the PIN code Change the PIN code lock settingEnter a PIN code Change the PIN code Lamp counter reset FanFan control Lamp counterFactory default Factory defaultFilter counter Filter counterInformation Input Source Information DisplayProjector is shut down and the Warning indicator lights red Maintenance and CleaningNote Then check the matters below Maintenance and Cleaning Cleaning the Filters Resetting the Filter CounterCleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CapCleaning the Projector Cabinet Maintenance and Cleaning Lamp Replacement Reset the lamp replacement counterMaintenance and Cleaning Service Parts No 345Troubleshooting AppendixAppendix Remote Control does Indicator blinks or lightsImage is distorted or runs off PIN code dialog box appearsAppendix Appendix Menu Tree Computer Input/Video InputSound Computer InputSetting Video InputAppendix Indicators and Projector Condition IndicatorsAppendix Compatible Computer Specifications ON-SCREEN ResolutionTechnical Specifications Optional Parts Appendix PJ Link Notice Appendix Configurations of Terminals Control Port Connector D-sub 9 pinPIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No Dimensions West Coast Branch HeadquartersGermany Elmo Europe G.m.b.H