Onkyo HT-S3300 instruction manual Hdmi Setup

■AM Freq Step (Asian models)

`10kHz:

Select if 10 kHz steps are used in your area.

`9kHz:

Select if 9 kHz steps are used in your area.

HDMI Setup

Menu HDMI Setup

■Audio TV OUT

`Off:

HDMI audio is not output.

`On:

HDMI audio is output.

This preference determines whether audio received at the HDMI IN is output by the HDMI OUT. You may want to turn this preference on if your TV is connected to the HDMI OUT and you want to listen to the audio from a component that’s connected to an HDMI IN, through your TV’s speakers. Normally, this should be set to “Off”.

Note

•If “On” is selected and the signal can be output by the TV, the AV receiver will output no sound through its speakers.

•If “On” is selected, “TV Sp On” appears on the display by pressing DISPLAY.

•When “TV Control” is set to “On”, this setting is fixed to “Auto”.

•With some TVs and input signals, no sound may be output even when this setting is set to “On”.

•When the “Audio TV OUT” setting is set to “On”, or “TV Con- trol” is set to “On” and you’re listening through your TV’s speakers (➔ 16), if you turn up the AV receiver’s volume con- trol, the sound will be output by the AV receiver’s front left and right speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.

■LipSync

`Disable:

HDMI lip sync disabled.

`Enable:

HDMI lip sync enabled.

The AV receiver can be set to automatically correct any delay between the video and the audio, based on the data from the connected monitor.

Note

•This function works only if your HDMI-compatible TV supports HDMI Lip Sync.

•You can check the amount of delay being applied by the HDMI Lip Sync function on the A/V Sync screen.

■HDMI Control (RIHD)

`Off:

pdisabled.

`On:

penabled.

This function allows p-compatible components connected via HDMI to be controlled with the AV receiver (➔ 53 to 55).

En

Note

•When set to “On” and close the menu, the name of connected p-compatible components and “RIHD On” are dis-

played on the AV receiver.

“Search…” → “(name)” → “RIHD On”

When the AV receiver cannot receive the name of the compo- nent, it is displayed as “Player*” or “Recorder*”, etc (“*” means the number of two or more component).

When set to “Off” and close the menu, “RIHD Off” are dis-

played on the AV receiver.

“Disconnect” → “RIHD Off”

•When an p-compatible component is connected to the AV receiver via the HDMI cable, the name of the connected component is displayed on the AV receiver display. For example, while you are watching TV broadcasting, if you operate a Blu-ray Disc/DVD player (being powered on) by the remote control of the AV receiver, the name of the Blu-ray Disc/DVD player is displayed on the AV receiver.

•Set to “Off” when a connected piece of equipment is not com- patible or it is unclear whether the equipment is compatible or not.

•If movement is unnatural when set to “On”, change the setting to “Off”.

•Refer to the connected component’s instruction manual for details.

■Audio Return Ch (ARC)

`Off:

Select “Off” if you don’t want to use audio return channel (ARC) function.

`Auto:

The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver.

Audio return channel (ARC) function enables an HDMI

1.4capable TV to send the audio stream to the HDMI OUT of the AV receiver. To use this function, you must select the TV/CD input selector and your TV must support ARC function.

Note

•The “Audio Return Ch” setting can be set only when the above “HDMI Control” setting is set to “On”.

•This setting is set to “Auto” automatically when the above “HDMI Control” is set to “On” first time.

■Power Control

`Off:

Power Control disabled.

`On:

Power Control enabled.

To link the power functions of p-compatible components connected via HDMI, select “On”. This setting is set to “On” automatically when the above “HDMI Control” is set to “On” first time.

36