Sim2 Multimedia SVP 420 HB manual Installation Installation Procedure, Removing the front panel

Page 16

4INSTALLATION

4.1INSTALLATION PROCEDURE

Qualified personnel must carefully observe the installation procedure to install the projector and to ensure best performances.

Note: The projector is factory-set for front ceiling projection with a 90” screen, 4/3 format and a projector-screen distance of 265 cm.

1.Choose the installation type and read the instructions through carefully. Determine the distance between the screen and the front of the projector.

Determine the projection angle.

2.Remove the top and front projector covers.

3.Insert the correct spacers between lenses and tubes.

4.Prepare and install the screen.

5.Install the projector on the floor or on the ceiling and center the screen, maintaining the factory deflection settings.

6.Focus carefully by adjusting the lenses.

7.If the installation type is the same as the factory setting, go to step 11, otherwise continue.

8.Tilt the red and blue tubes until the three crosses are superimposed.

9.Adjust the magnets.

10.Switch the projector off and disconnect the power cable.

11.Put the cover on the video projector.

12.Carry out a fine adjustment of the picture with the remote control RC 3000.

4.2 Removing the cover

4.2.1 Removing the top cover

Loosen the 2 securing screws (A) and lift the cover up.

A

SVP 450 PLUS - SVD 500 PLUS

To remove the top cover completely you must unscrew the two locking screws (B) close to the two pivots and the other two (C) securing the jointed rod to the cover.

C

B

4.2.2 Removing the front panel

Unscrew the two screws (D) on the left and right of the front panel. Unscrew the three screws (E) on the bottom and take the panel off. The position of the screws is shown by the arrows. To remove the front panel, press the two tongues (F), which are located in its lower portion.

D

D F E

F

E

4.3 INSTALLATION TYPES

4.3.1 Installation choice

Choose one of the following possible installation types:

•DESK TOP FRONT projection

•DESK TOP REAR projection

•CEILING FRONT projection

•CEILING REAR projection

ENGLISH

15

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Video Projector User Remote Control RC InstallationIndex General InformationComplete Function RC 3000 Remote Control .......... Electric Shock Hazard Do not Open Mains Power Safety and RegulationsProjector Identification General InformationPower cabling ServicingSpare parts Servicing must be carried out by qualified techniciansCleaning the projector Packing the ProjectorRoom lighting Back panelPower switch Cathode-ray tube phosphor burningFollowing Functions are on the Panel Led pilot light. Red = STAND-BY, Green = onUser Remote Control RC Exit Enter VCR Memo UPC Mute InfoRC 3100 User Remote Control Projector Power OnPicture adjustment BatteriesScreen format selection VCR button Sync filterInfo NORMAL, SMALL, 16/9, Letter BOX, CinemaMuting video button Normalised buttonUPC button Freeze buttonBlanking White menuUPC converter Storing Switched onMenu operates only if the UPC converter is Installation menu How to enter the installation modeInstallation Installation Procedure Installation TypesInstallation choice Removing the cover Removing the top coverDesk-top front projection Desktop rear projectionFront Projection Desktop Rear ProjectionCeiling front projection MuroCeiling rear projection Projection angle measurementSpacers Ceiling Front ProjectionFront view of the CRT Spacers changing Spacers tableCRT Lens 120 150180 200Optical and electrical adjustments Projector centeringBlue Green RED 100 120 150 180 30010Magnet adjustment Lens focus adjustmentMechanical centering of the tubes Setting of deflection connectors Convergence adjustmentRemote control Vertical Deflection HorizontalComplete Function RC3000 Remote Control Complete function RC3000 remote controlHow the RC 3000 remote control works Video setupTo setup the GAMMAADJ., you must enter installation mode White Cross Hatch Dots Pattern Test patternWindow Cross Hair Colour Bars White balance Memory managerHow to insert a label How to change an aspect ratio flagHorizontal and vertical frequencies First of all, you must enter the memory managerLoad How to store a new input signalCopy Delete MoveThis function allows you to delete a memory bank Installation types To select the type of installationOptions menu To change the displaying timeFine picture adjustments First of all you must enetr the installation modeDeflection Deflection centreDeflection dimensions Deflection pincushion topDeflection pincushion bottom Keystone correctionCentral convergence Convergence linearityConvergence sizes Convergence skew Convergence bowConvergence pincushion Convergence bordersScreen quarters corrections How to store the convergence adjustments How to reset the adjustmentsScreen corners corrections Technical Specifications Display Performances Electrical Data Supplied AccessoryMechanical Data Problem Causes Remedy TroubleshootingMeaning Anweisungen AUF Deutsch 13.1Hinweis gemäß behördlicher VorschriftenCod

SVD 500 PLUS, SVP 420 HB, SVP 450 PLUS specifications

Sim2 Multimedia has long been a pioneer in the realm of high-performance projectors, and their products such as the SVP 450 PLUS, SVP 420 HB, and SVD 500 PLUS continue to uphold that legacy with exceptional features and cutting-edge technology.

The SVP 450 PLUS is designed for those seeking a premium viewing experience. It boasts a high-resolution DLP engine with 4K upscaling capabilities, delivering crystal-clear images with vibrant colors. Utilizing advanced color processing technology, the SVP 450 PLUS excels in enhancing color accuracy and contrast, making it ideal for both home theater setups and professional presentations. The projector also supports a variety of input options, allowing for seamless connectivity to a range of devices, including streaming boxes and laptops. Its quiet operation and long-lasting lamp life further enhance its appeal, ensuring that users can enjoy extended viewing sessions without distraction.

Meanwhile, the SVP 420 HB is tailored for users who prioritize flexibility and portability. This model features a compact design without compromising on performance. With a native resolution of 1080p, the SVP 420 HB still delivers sharp images and bright colors, ideal for both indoor and outdoor settings. Its integrated Wi-Fi capabilities allow for wireless streaming, giving users the freedom to connect their devices easily. The projector's lightweight construction and built-in rechargeable battery make it a go-to choice for professionals on the move, educators, or even outdoor movie nights.

The SVD 500 PLUS represents the pinnacle of Sim2's technology, designed for high-end applications such as large venues and auditoriums. This projector comes equipped with a powerful laser light source that offers longer lifespan and higher brightness levels, ensuring optimal performance in well-lit environments. The SVD 500 PLUS features sophisticated image processing technologies which enhance dynamic range and clarity, providing an immersive viewing experience. Additionally, its advanced lens options allow for significant flexibility in installation, accommodating various room sizes and configurations.

In conclusion, the Sim2 Multimedia SVP 450 PLUS, SVP 420 HB, and SVD 500 PLUS projectors showcase the brand’s commitment to innovation and quality. Whether for personal or professional use, these models incorporate advanced technologies and features that cater to diverse viewing needs while delivering unparalleled performance.
Top Page Image Contents