Onkyo TX-DS898 Recording a source, Rec Out, Start recording at the recording component as desired

Page 53

Recording a source

Input source buttons

STANDBY/ON

STANDBY

POWER

ONOFF

ZONE 2 (GRN )

AUDIO

REC ( RED )

DVD

VIDEO 1

VIDEO 2

VIDEO 3

VIDEO 4

VIDEO 5

TAPE

FM

AM

PHONO

C D

PURE AUDIO UPSAMPLING

SELECTOR

MASTER VOLUME

DISPLAY

PHONES	REC OUT ZONE 2	OFF	STEREO SURROUND THX	DSP	DIMMER FM MODE MEMORY SETUP	ENTER	RETURN	VIDEO 5/VIDEO CAM INPUT

ZONE 2 LEVEL					CLEAR	TUNING	PRESET	S VIDEO	VIDEO	L AUDIO R
							DIGITAL

REC OUT

To record the input source signal you are currently watching or listening to

This method outputs to the audio and video outputs the currently selected input source signal. This method allows you to a signal while you are actually listening to or watching it.

1.Select the input source to record by pressing the corresponding input source button.

The input source is now selected and you may watch or listen to it as desired.

2.Press the REC OUT button repeatedly until “Rec Sel:SOURCE” appears in the front display.

The currently selected input source signal to the TAPE OUT, VIDEO 1 OUT, VIDEO 2 OUT outputs for recording.

3.Start recording at the recording component as desired.

To confirm the settings, press the Rec Out button. The current settings will appear for 3 seconds in the front display.

Notes:

•If you change the input source during recording, you will record the signals from the newly selected input source.

•You cannot record the surround effects.

•Digital signals input to the DIGITAL INPUT (COAXIAL) and DIGITAL INPUT (OPTICAL) inputs will be output to the DIGITAL OUTPUT (OPTICAL) output.

•Digital input signals are only output to the digital outputs and analog input signals are only output from the analog outputs. There is no conversion from digital to analog or vice versa. When connecting CD players and other digital components, do not connect only the digital terminals, but the analog ones as well.

•There are some restrictions on recording digital signals. When making digital recordings, consult the instruction manual that came with your digital recording equipment (e.g., MD recorder or DAT deck) to know what restrictions are imposed.

•You cannot record the source connected to the MULTI CHANNEL INPUT connector.

53

Image 53

Contents TX-DS898 Avis Important SafeguardsPrecautions Contents Contents Supplied accessories FeaturesUsing the remote controller Before using this unitInstalling the remote controller batteries Front panel Front panel facilitiesFront door Front panel displayFront panel facilities Remote controller Remote controller Digital INPUT/OUTPUT coaxial and optical Rear panel facilities3 4 Rear panel facilitiesVideo IN/OUT IR IN/OUTMulti Channel Input GNDConnecting a turntable PH Connecting your audio componentsConnecting a compact disc player CD ConnectionsFlow of the video signals is as follows Connecting your video componentsConnecting a DVD player DVD ConnectionsConnecting a video cassette recorder Video Connecting a television monitor or projector Connecting video camera, etc. VideoIdeal speaker configuration Connecting speakersMinimum speaker configuration for surround sound playback Speaker placementConnecting speakers Connecting speakersConnecting the speaker cable Connecting a subwooferWhen using the Surr BACK/ZONE 2 Speakers terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 OUT terminals When using the Surr BACK/ZONE 2 PRE OUT terminalsFrom connecting block Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an FM outdoor antenna Connecting antennasConnecting an AM outdoor antenna Directional linkagePower Connecting the powerSTANDBY/ON Stdby RcvrAdvanced Menu Setup menusBasic Menu Press the Setup button Setup menusNavigating through the Setup menu Hardware Setup menu Hardware SetupIR in Setup sub-menu Speaker Impedance sub-menuSpeaker Config sub-menu Speaker SetupSpeaker Setup menu Speaker Distance sub-menu Speaker SetupCalibrating the speaker levels Level Calibration sub-menuLeft RightPeak Level Bass Peak Level Bass Peak Level Manager* sub-menuBass Peak Level Limiter Input Setup menu Input SetupDigital Setup sub-menu Initial settings for each input sourceMultichannel Setup sub-menu Input SetupDigital Input Digital FormatLast Valid enables the source last selected The source that Video Setup sub-menuVideo Component VideoIntelli Volume Intelli Volume sub-menuCharacter Input sub-menu Character DisplayRelationship between input source and listening mode Listening Mode Preset sub-menuListening Modes Input source signalsDTS-ES Discrete DTS Neo6DTS-ES Matrix THX CinemaAudio Adjust Setup menu Audio AdjustAudio Adjust Surr Mode Analog/PCM Surround SetupSurr Mode D.F.2ch Pro Logic II Music DimensionDecoder THX SetupTHX Surround EX Dolby D Front EffectPreference menu Volume Setup sub-menuPreference OSD Setup sub-menu Headphones Level Setup sub-menuPreference OSD Position sub-menuListening to Radio Broadcasts Tuning into a radio stationListening to a stereo radio station FM mode Erasing a preset radio station Presetting a radio station Selecting a preset radio stationListening to Radio Broadcasts Memory EnterListening with headphones Adjusting the bass and trebleEnjoying music or videos with the TX-DS898 Temporarily turning off the soundEntering characters using the TX-DS898 Changing the listening modeDirect Setup Pure Audio Enter Return Enjoying music or videos with the TX-DS898Adjusting the brightness of the front display Switching the displayUsing the sleep time remote controller only Temporarily changing the speaker output levelsEnjoying the multichannel output Changing the audio modeSelecting an input source using the remote controller Playing music using the buttons on the TX-DS898Adjusting the volume for the remote zone Enjoying music in the remote zoneStart recording at the recording component as desired Recording a sourceREC OUT Recording a source Calling up a preset radio station Using remote controllerOverview Controlling an Onkyo cassette tape deckDisc Stdby CD Mode Using remote controllerPress the CD Mode button Controlling an Onkyo CD playerControlling an Onkyo DVD player On Stdby MD Mode SAT, CABLE, VCR, and TV Mode buttonsPress the MD Mode button Controlling an Onkyo MD recorderLearning a pre-programming code When entering the code of Onkyo DVD playersLearning a pre-programming code DisplayPre-programming codes Learning a pre-programming codeDVD CableDVD Mode DVD Player Mode Operating your programmed remote controllerSAT Mode Satellite Tuner Mode Cable Mode Cable ModeVCR Mode VCR Mode Operating your programmed remote controllerTV Mode TV Mode On Stdby VCR Mode VOL TV/VCR MutingLight Direct Mode Macro Macro Programming procedurePage Erasing all the commands programmed under a Mode button Erasing the programmed command from one buttonPress and release the same Mode button again Press and release the same button againWhat is a Macro function? Using a Macro functionMode Macro Programming a Macro functionRcvr CD Mode Using a Macro functionProgramming the Direct Macro function Running a Direct Macro functionPress the Mode Macro button again Erasing a macro from the Mode Macro buttonErasing a direct macro from the Direct Macro button Direct MacroMacro mode programming memo Erasing all commands and macros that have been programmedOn Stdby Enter Press the Enter buttonTroubleshooting guide If one of the messages shown below appears Troubleshooting guideVideo and Audio Amplifier Section Specifications