Onkyo TX-SR574 instruction manual Installing the Batteries, Aiming the Remote Controller

Page 11

Remote Controller

Installing the Batteries

1 To open the battery compartment, press the small hollow and slide open the cover.

Aiming the Remote Controller

When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below.

Remote control sensor

AV receiver

STANDBY indicator

2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment.

3 Slide the cover shut.

Notes:

If the remote controller doesn’t work reliably, try replacing the batteries.

Don’t mix new and old batteries or different types of batteries.

If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

Expired batteries should be removed as soon as possi- ble to prevent damage from leakage or corrosion.

Approx. 16 ft. (5 m)

Notes:

The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sun- light or inverter-type fluorescent lights. Keep this in mind when installing.

If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote control- ler may not work reliably.

Don’t put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries.

The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing.

The remote controller will not work if there’s an obsta- cle between it and the AV receiver’s remote control sensor.

11

Image 11
Contents TX-SR574 Avis Important Safety InstructionsFCC Information for User PrecautionsPower For models having a power cord with a polarized plugSpeaker cable labels Supplied AccessoriesPrecautions Make sure you have the following accessoriesFeatures Speaker Set B Sub Room Enjoying Home TheaterSpeaker Sets a and B Speaker Set a Main RoomContents Front Panel Getting to Know the AV ReceiverDisplay Getting to Know the AV ReceiverVideo 1 IN/OUT and Video 2 Rear PanelDigital in Optical 1, 2, 3, and Coaxial Front Speakers A, Surround SPEAKERS, Center SPEAKER,Aiming the Remote Controller Remote ControllerInstalling the Batteries RECEIVER/TAPE Mode Remote ControllerUsing the Remote Controller ON/STANDBY button Listening Mode buttonsRemote Mode buttons Buttons used when the Tuner input is selectedDVD Mode Arrow / and Enter buttons CD/MD/CDR/HDD ModeTo select the input source, press DISC/ALBUM +/- buttonSpeaker Configuration Connecting Your SpeakersSpeaker Connection Precautions Read the following before connecting your speakersConnecting a Powered Subwoofer Connecting Your SpeakersConnecting Speaker Set a Connecting Speaker Set B Attach the FM antenna, as shown American Model Connecting AntennasConnecting the Indoor FM Antenna Connecting the AM Loop AntennaUsing a TV/FM Antenna Splitter Connecting AntennasConnecting an Outdoor FM Antenna Connecting an Outdoor AM AntennaAV Connection Color Coding Connecting Your ComponentsAbout AV Connections Optical Digital JacksVideo Connection Formats Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Which Connections Should I Use?Hint Connecting a TV or ProjectorVideo Connection Audio ConnectionAntenna Connecting a DVD playerDVD player Hooking Up the Multichannel DVD InputDVD recorder Connecting a VCR or DVD Recorder for PlaybackVCR Camcorder or console Connecting a VCR or DVD Recorder for RecordingConnecting a Camcorder, Games Console, or Other Device Make the video connection a Make the audio connection aSatellite, cable, set-top box, etc Phono preamp StepReceiver’s Video 2 in L/R jacks and Video 2 in S Jacks Connecting an HDD-compatible ComponentCassette recorder, CDR, etc Connecting a Cassette, CDR, MiniDisc, or DAT RecorderConnecting the Power Cord of Another Component SeeRemote Control Connecting Onkyo ComponentsConnecting the Power Cord Auto Power On/StandbyHave you connected a component to a digital audio input? Turning On the AV ReceiverTurning On and Standby Smooth Operation in a Few Easy StepsChanging the Input Display First Time SetupAssigning Digital Inputs to Input Sources Component Video Setup First Time SetupMinimum Speaker Impedance Setup not North American model Setup closes Press the Setup buttonLeft and Right / but- tons to select Small, Large, or None Testing the SpeakersPress the remote controller’s Test Tone but- ton Use the Down button toStart playback on the source component Select a suitable listening mode and enjoyPlaying Your AV Components Basic AV Receiver OperationDisplaying Source Information Using the Multichannel DVD InputPlaying Your AV Components Listening to AM/FM stations Tuning into AM/FM Radio StationsListening to the Radio Listening to the Radio Presetting Radio StationsMuting the AV Receiver Adjusting the Bass and TrebleSetting the Display Brightness Common FunctionsCommon Functions Using the Sleep TimerAdjusting Speaker Levels Using HeadphonesSelecting on the AV Receiver Using the Listening ModesSelecting with the Remote Controller Selecting Listening ModesPCM*1 Using the Listening ModesDTS About the Listening ModesOnkyo Original DSP Modes Use this mode with any stereo movie e.g., TV, DVD, VHSUsing the Audio Adjust Settings Using the Late Night Function Dolby Digital onlyUsing the CinemaFILTER Dolby Digital EX Input Signal Setting Input Channel SettingsPlii and PLIIx Music Mode Settings DTS Neo6 Music Mode SettingRecording Audio and Video from Separate Sources RecordingRecording the Input Source Double Bass Advanced SetupAdvanced Speaker Settings Crossover FrequencySpeaker Levels Advanced SetupSpeaker Distance Digital Input Signal Formats Input Selector Mode buttonCorrecting Sound and Picture Sync Controlling Other Components Entering Remote Control CodesControlling Other Components Remote Control Codes for Onkyo Components Connected viaResetting Remote Mode Buttons Resetting the Remote ControllerCH + ON/STANDBY, TVTV VOL Troubleshooting Troubleshooting Can’t record Remote controller doesn’t workSound changes when I connect my head- phones Can’t control other componentsVideo ATT2 Gain is reduced by 2 dB Video ATT0 defaultMemory Backup Video AttenuationTuner Section SpecificationsAmplifier Section Video SectionPage Page Onkyo China Limited Onkyo U.S.A. CorporationOnkyo Europe Electronics GmbH Onkyo Europe UK Office