Onkyo TX-SR574 Common Functions, Using the Sleep Timer, Adjusting Speaker Levels

Page 42

Common Functions—Continued

Using the Sleep Timer

With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period.

Press the remote controller’s [SLEEP] button repeatedly to select the required sleep time.

SLEEP

You can set the sleep time from 90 to 10 minutes in 10 minute steps.

The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 sec- onds, then the previous display reap- pears.

SLEEP indicator

To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears.

To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you’ll shorten the sleep time by 10 minutes.

Adjusting Speaker Levels

You can adjust the volume of each speaker in speaker set A. These temporary adjustments are cancelled when the AV receiver is set to Standby.

1

Use the remote controller’s

 

CH SEL

[CH SEL] button to select each

speaker, and use the [LEVEL–]

 

 

and [LEVEL+] buttons to adjust

 

the volume.

LEVEL- LEVEL+

You can adjust the volume of each

speaker from –12 dB to +12 dB

 

 

(–15 dB to +12 dB for the subwoofer).

Notes:

You cannot use this function while the AV receiver is muted.

Speakers that are set to No or None in the Speaker Configuration cannot be adjusted.

Speaker Set B

While speaker set B is on, you can adjust the volume of the left and right speakers, from –12 dB to +12 dB.

Using Headphones

For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver’s PHONES jack.

STANDBY/ON

STANDBY

PHONES

These settings are stored when the AV receiver is set to Standby.

While speaker set B is on, you cannot adjust the levels of speaker set A’s surround back speakers.

Headphones

While a pair of headphones is connected, you can adjust the volume of each headphone speaker, from –12 dB to +12 dB each.

Notes:

Always turn down the volume before connecting your headphones.

Speaker sets A and B are turned off while the head- phones plug is inserted in the PHONES jack.

When you connect a pair of headphones, the listening mode is set to Stereo, unless it was set to Pure Audio (not North American model), Mono, Stereo, or Direct, in which case it stays the same.

When the multichannel DVD input is selected, only the front left and front right channels can be heard in the headphones.

These settings are stored when the AV receiver is set to Standby.

42

Image 42
Contents TX-SR574 Important Safety Instructions AvisFor models having a power cord with a polarized plug PrecautionsPower FCC Information for UserMake sure you have the following accessories Supplied AccessoriesPrecautions Speaker cable labelsFeatures Speaker Set a Main Room Enjoying Home TheaterSpeaker Sets a and B Speaker Set B Sub RoomContents Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayFront Speakers A, Surround SPEAKERS, Center SPEAKER, Rear PanelDigital in Optical 1, 2, 3, and Coaxial Video 1 IN/OUT and Video 2Remote Controller Installing the BatteriesAiming the Remote Controller Remote Controller Using the Remote ControllerRECEIVER/TAPE Mode Buttons used when the Tuner input is selected Listening Mode buttonsRemote Mode buttons ON/STANDBY buttonDVD Mode DISC/ALBUM +/- button CD/MD/CDR/HDD ModeTo select the input source, press Arrow / and Enter buttonsRead the following before connecting your speakers Connecting Your SpeakersSpeaker Connection Precautions Speaker ConfigurationConnecting Your Speakers Connecting Speaker Set a Connecting Speaker Set BConnecting a Powered Subwoofer Connecting the AM Loop Antenna Connecting AntennasConnecting the Indoor FM Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor AM Antenna Connecting AntennasConnecting an Outdoor FM Antenna Using a TV/FM Antenna SplitterOptical Digital Jacks Connecting Your ComponentsAbout AV Connections AV Connection Color CodingWhich Connections Should I Use? Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Video Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD player AntennaHooking Up the Multichannel DVD Input DVD playerConnecting a VCR or DVD Recorder for Playback VCRDVD recorder Make the video connection a Make the audio connection a Connecting a VCR or DVD Recorder for RecordingConnecting a Camcorder, Games Console, or Other Device Camcorder or consoleSatellite, cable, set-top box, etc Step Phono preampConnecting an HDD-compatible Component Receiver’s Video 2 in L/R jacks and Video 2 in S JacksSee Connecting a Cassette, CDR, MiniDisc, or DAT RecorderConnecting the Power Cord of Another Component Cassette recorder, CDR, etcAuto Power On/Standby Connecting Onkyo ComponentsConnecting the Power Cord Remote ControlSmooth Operation in a Few Easy Steps Turning On the AV ReceiverTurning On and Standby Have you connected a component to a digital audio input?First Time Setup Assigning Digital Inputs to Input SourcesChanging the Input Display First Time Setup Minimum Speaker Impedance Setup not North American modelComponent Video Setup Press the Setup button Setup closesUse the Down button to Testing the SpeakersPress the remote controller’s Test Tone but- ton Left and Right / but- tons to select Small, Large, or NoneBasic AV Receiver Operation Select a suitable listening mode and enjoyPlaying Your AV Components Start playback on the source componentUsing the Multichannel DVD Input Playing Your AV ComponentsDisplaying Source Information Tuning into AM/FM Radio Stations Listening to the RadioListening to AM/FM stations Presetting Radio Stations Listening to the RadioCommon Functions Adjusting the Bass and TrebleSetting the Display Brightness Muting the AV ReceiverUsing Headphones Using the Sleep TimerAdjusting Speaker Levels Common FunctionsSelecting Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes PCM*1About the Listening Modes DTSUse this mode with any stereo movie e.g., TV, DVD, VHS Onkyo Original DSP ModesUsing the Late Night Function Dolby Digital only Using the CinemaFILTERUsing the Audio Adjust Settings DTS Neo6 Music Mode Setting Input Channel SettingsPlii and PLIIx Music Mode Settings Dolby Digital EX Input Signal SettingRecording Recording the Input SourceRecording Audio and Video from Separate Sources Crossover Frequency Advanced SetupAdvanced Speaker Settings Double BassAdvanced Setup Speaker DistanceSpeaker Levels Digital Input Signal Formats Mode button Correcting Sound and Picture SyncInput Selector Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Controller Remote Control Codes for Onkyo Components Connected viaResetting Remote Mode Buttons Controlling Other ComponentsON/STANDBY, TV TV VOLCH + Troubleshooting Troubleshooting Can’t control other components Remote controller doesn’t workSound changes when I connect my head- phones Can’t recordVideo Attenuation Video ATT0 defaultMemory Backup Video ATT2 Gain is reduced by 2 dBVideo Section SpecificationsAmplifier Section Tuner SectionPage Page Onkyo Europe UK Office Onkyo U.S.A. CorporationOnkyo Europe Electronics GmbH Onkyo China Limited