Runco CR-26HD, CR-32HDi manual DVI/Computer Input Digital, Audio Input RGB/DVI, Atsc DTV Input

Page 19

Controls and Functions

8.DVI/Computer Input (Digital)

HDCP-compliant digital video input for connecting a DVD player, personal computer or HD tuner with a DVI or HDMI output.

For best results, do not run your DVD player in progressive mode.

Tip

9.Audio Input (RGB/DVI)

Connect the audio output from your RGB or DVI source here.

10.ATSC DTV Input

75-ohm coaxial input for connecting a TV antenna or CATV system to the digital TV tuner.

11.INPUT 3 Component Video (RCA connectors)

Standard-definition (480i/576i) or high-definition (720p/1080i), YPrPb component input. This is the input for component video from sources such as DVD players.

12.INPUT 3 Composite Video Input

13.INPUT 3 Audio Input

Connect the audio output from your Input 3 source here.

14.INPUT 1 COMPOSITE VIDEO INPUT

15.INPUT 1 Audio Input

Connect the audio output from your Input 1 source here.

16.INPUT1 S-Video Input

17.RS-232 CONTROL PORT

A male, 9-pin D-sub connector for interfacing with a PC or home theater automation/control system.

18.MONITOR-OUT (Audio)

19.MONITOR-OUT (Composite Video)

Runco CR-26HD/CR-32HDi Owner’s Operating Manual

7

Image 19
Contents CR-26HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures Xii About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Speakers Controls and IndicatorsControls and Functions Crystal Series LCD Display at a GlanceInputs and Outputs Crystal Series LCD DisplayInput 2 Audio Input Input 2 Composite Video Input Atsc DTV Input Input 3 Component Video RCA connectorsDVI/Computer Input Digital Audio Input RGB/DVICrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlNumeric Buttons Timer OFF ButtonMemory Preset Buttons OFF / onVwide VirtualWide Aspect Ratio Selection Buttons ANA Anamorphic4X3 Standard Letbox LetterboxFavorite Channel Selection Buttons Sound Control ButtonsSurrnd Surround MTS/SAP Multichannel Television Sound/Second Audio ProgramControls and Functions Remote Control InstallationBattery Installation Installation Overview Quick SetupStep Procedure For Details, refer to Other Considerations Installation ConsiderationsWall-Mounting the Crystal Series LCD Display Ambient LightAntenna/Cable TV Connection Connections to the Crystal Series LCD DisplayDVI Connections Analog RGB Connections Refer to Computer/Video Signal Compatibility on page 56 forInput Input ConnectionRS-232 Controller Connector Pin AssignmentsLeft Side Installation Operation Turning on the PowerChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Source Picture AdjustTimer SetupTV Input1 Input2 Input3 Main MenuSource Aspect RatioRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Adjust Typical Pluge Pattern for Adjusting BrightnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Balance Equalizer Surround Audio Language TV Speaker AudioChannel TimerChannel Auto Tuning Add/Erase Favorite Channel Timer On Timer Off Timer Sleep Timer Time ZoneSetup Characteristics of the incoming signalRating/Category Description FCC Ratings and Content CategoriesOffensive language Menu should be used by ISF-certified technicians only ISF Calibration Picture Adjust White Balance Blue EnableGamma Baud Rate Command Ack Factory Reset Splash Duration ISF CalibrationOffset White Balance GainCrystal Series LCD Display Splash Screen Using Picture-In-Picture PIP Available Main and PIP Source Combinations Button on the remote controlMain Aspect Size Position PIP Swap Swap TV/AV Mode PIP Audio Programs Swap button on the remote control PIP Images Button on the remote controlSwapping the Main Mono+SAP Broadcast Mode Receive Mode Mono StereoStereo Sound/SAP Compatibility with Stereo and SAP Audio BroadcastsOperation Troubleshooting Chart Maintenance and TroubleshootingCleaning Troubleshooting TipsComputer/Video Signal Command Description RS-232 Connection and Port ConfigurationSerial Command Syntax Serial CommandsSAB Key 0002 0043 Specifications are subject to change without notice SpecificationsCrystal Series LCD Display Specifications Crystal Series LCD Display SpecificationsCR-26HD Dimensions Crystal Series LCD Display DimensionsCR-32HDi Dimensions Computer/Video Signal Compatibility Chart Computer/Video Signal CompatibilityPage Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 68 pages 21.6 Kb