Runco High-Definition, CR-26HD, CR-32HDi manual Analog RGB Connections

Page 30

Installation

RGB Connections: The Crystal Series LCD Display has an RGB input for connecting a personal computer; see Figure 3-3.

Rear of the Display

Rear of the PC

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

Audio Cable

(Sold Separately)

D-Sub 15 Pin Cable (Sold Separately)

Figure 3-3. Analog RGB Connections

1. Refer to Computer/Video Signal Compatibility on page 56 for

Note

a list of computer signals compatible with the Crystal Series LCD

 

 

Display. Use with signals other than those listed may cause some

 

functions not to work.

2.Some Macintosh computers may require a Macintosh video adapter. Contact your nearest authorized service center or dealer.

3.This Crystal Series LCD Display may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, switch the notebook computer to “CRT only” mode. If you are unsure how to do this, refer to your notebook computer’s user manual.

18

Runco CR-26HD/CR-32HDi Owner’s Operating Manual

Image 30
Contents CR-26HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Crystal Series LCD Display at a Glance Controls and IndicatorsControls and Functions SpeakersCrystal Series LCD Display Inputs and OutputsInput 2 Audio Input Input 2 Composite Video Input Audio Input RGB/DVI Input 3 Component Video RCA connectorsDVI/Computer Input Digital Atsc DTV InputCrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlOFF / on Timer OFF ButtonMemory Preset Buttons Numeric ButtonsLetbox Letterbox Aspect Ratio Selection Buttons ANA Anamorphic4X3 Standard Vwide VirtualWideMTS/SAP Multichannel Television Sound/Second Audio Program Sound Control ButtonsSurrnd Surround Favorite Channel Selection ButtonsControls and Functions Installation Remote ControlBattery Installation Quick Setup Installation OverviewStep Procedure For Details, refer to Ambient Light Installation ConsiderationsWall-Mounting the Crystal Series LCD Display Other ConsiderationsConnections to the Crystal Series LCD Display Antenna/Cable TV ConnectionDVI Connections Refer to Computer/Video Signal Compatibility on page 56 for Analog RGB ConnectionsInput Connection InputConnector Pin Assignments RS-232 ControllerLeft Side Installation Turning on the Power OperationChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Setup Picture AdjustTimer SourceAspect Ratio Main MenuSource TV Input1 Input2 Input3Aspect Ratio Settings Remote Aspect Ratio Control Description KeyTypical Pluge Pattern for Adjusting Brightness Picture AdjustTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Audio Balance Equalizer Surround Audio Language TV SpeakerTimer On Timer Off Timer Sleep Timer Time Zone TimerChannel Auto Tuning Add/Erase Favorite Channel ChannelCharacteristics of the incoming signal SetupFCC Ratings and Content Categories Rating/Category DescriptionOffensive language ISF Calibration ISF Calibration Picture Adjust White Balance Blue EnableGamma Baud Rate Command Ack Factory Reset Splash Duration Menu should be used by ISF-certified technicians onlyWhite Balance Gain OffsetCrystal Series LCD Display Splash Screen Using Picture-In-Picture PIP Button on the remote control Available Main and PIP Source CombinationsMain Aspect Size Position PIP Swap Swap TV/AV Mode PIP Images Button on the remote control PIP Audio Programs Swap button on the remote controlSwapping the Main Compatibility with Stereo and SAP Audio Broadcasts Broadcast Mode Receive Mode Mono StereoStereo Sound/SAP Mono+SAPOperation Troubleshooting Tips Maintenance and TroubleshootingCleaning Troubleshooting ChartComputer/Video Signal Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax Command DescriptionSAB Key 0002 0043 Crystal Series LCD Display Specifications SpecificationsCrystal Series LCD Display Specifications Specifications are subject to change without noticeCrystal Series LCD Display Dimensions CR-26HD DimensionsCR-32HDi Dimensions Computer/Video Signal Compatibility Computer/Video Signal Compatibility ChartPage Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 68 pages 21.6 Kb