Runco CR-26HD, CR-32HDi, High-Definition manual DVI Connections

Page 29

Installation

This Crystal Series LCD Display supports the VESA Display Data

Note Channel (DDC) standard. This standard provides “Plug and Play” capability; the display and a VESA DDC-compatible computer communicate their setting requirements, allowing for quick and easy setup.

In order for Plug and Play to work correctly, you must turn on the display before you turn on the connected computer.

Rear of the Display

Audio Cable

DVI-D Cable or DVI-to-HDMI Cable (sold separately)

Rear of the Display

Rear of the PC

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

Audio Cable

(Sold Separately)

DVI-D Cable (Sold Separately)

Figure 3-2. DVI Connections

Runco CR-26HD/CR-32HDi Owner’s Operating Manual

17

Page 28 Page 30
Image 29
Page 28 Page 30
Contents CR-26HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Specifications Maintenance and TroubleshootingOperation Serial CommunicationsList of Figures List of Figures Xii About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsCrystal Series LCD Display at a Glance SpeakersInput 2 Audio Input Input 2 Composite Video Input Crystal Series LCD DisplayInputs and Outputs DVI/Computer Input Digital Input 3 Component Video RCA connectorsAudio Input RGB/DVI Atsc DTV InputCrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlMemory Preset Buttons Timer OFF ButtonOFF / on Numeric Buttons4X3 Standard Aspect Ratio Selection Buttons ANA AnamorphicLetbox Letterbox Vwide VirtualWideSurrnd Surround Sound Control ButtonsMTS/SAP Multichannel Television Sound/Second Audio Program Favorite Channel Selection ButtonsControls and Functions Battery Installation InstallationRemote Control Step Procedure For Details, refer to Quick Setup Installation Overview Wall-Mounting the Crystal Series LCD Display Installation ConsiderationsAmbient Light Other ConsiderationsAntenna/Cable TV Connection Connections to the Crystal Series LCD DisplayDVI Connections Analog RGB Connections Refer to Computer/Video Signal Compatibility on page 56 forInput Input ConnectionLeft Side Connector Pin AssignmentsRS-232 Controller Installation Changing the OSD Language Turning on the PowerOperation Setting the PC Display Properties Using the On-Screen Menus Timer Picture AdjustSetup SourceSource Main MenuAspect Ratio TV Input1 Input2 Input3Remote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Adjust Typical Pluge Pattern for Adjusting BrightnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Balance Equalizer Surround Audio Language TV Speaker AudioChannel Auto Tuning Add/Erase Favorite Channel TimerTimer On Timer Off Timer Sleep Timer Time Zone ChannelSetup Characteristics of the incoming signalRating/Category Description FCC Ratings and Content CategoriesOffensive language Gamma Baud Rate Command Ack Factory Reset Splash Duration ISF Calibration Picture Adjust White Balance Blue EnableISF Calibration Menu should be used by ISF-certified technicians onlyOffset White Balance GainCrystal Series LCD Display Splash Screen Using Picture-In-Picture PIP Main Button on the remote controlAvailable Main and PIP Source Combinations Aspect Size Position PIP Swap Swap TV/AV Mode Swapping the Main PIP Images Button on the remote controlPIP Audio Programs Swap button on the remote control Stereo Sound/SAP Broadcast Mode Receive Mode Mono StereoCompatibility with Stereo and SAP Audio Broadcasts Mono+SAPOperation Cleaning Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartComputer/Video Signal Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Command DescriptionSAB Key 0002 0043 Crystal Series LCD Display Specifications SpecificationsCrystal Series LCD Display Specifications Specifications are subject to change without noticeCR-26HD Dimensions Crystal Series LCD Display DimensionsCR-32HDi Dimensions Computer/Video Signal Compatibility Chart Computer/Video Signal CompatibilityPage Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 68 pages 21.6 Kb
Top Page Image Contents