Runco High-Definition Quick Setup, Installation Overview, Step Procedure For Details, refer to

Page 26

Installation

3.2

Quick Setup

Table 3-1gives a quick overview of the Crystal Series LCD Display installation process. The sections following this one provide detailed instructions.

	Note	Installation should be performed by a qualified custom video
		installation specialist.
Table 3-1. Installation Overview

Step		Procedure	For Details, refer to
			page...


1	Mount the Crystal Series LCD Display on a wall (optional)		15

2	Connect signal sources to the Crystal Series LCD Display		16

3	Connect external controller to RS-232 port (optional)		21

4	Apply power to the Crystal Series LCD Display		23

5	Change the OSD language		23

6	If using the Crystal Series LCD Display with a PC, adjust PC		24
	display properties


	Display calibration: adjust the following for each input;		27 through 37
	save settings when finished:

•Brightness

7 • Contrast

•Color level

•Tint

•Input position

14	Runco CR-26HD/CR-32HDi Owner’s Operating Manual

Image 26

Contents CR-26HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Crystal Series LCD Display at a Glance Controls and IndicatorsControls and Functions SpeakersInput 2 Audio Input Input 2 Composite Video Input Crystal Series LCD DisplayInputs and Outputs Audio Input RGB/DVI Input 3 Component Video RCA connectorsDVI/Computer Input Digital Atsc DTV InputCrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlOFF / on Timer OFF ButtonMemory Preset Buttons Numeric ButtonsLetbox Letterbox Aspect Ratio Selection Buttons ANA Anamorphic4X3 Standard Vwide VirtualWideMTS/SAP Multichannel Television Sound/Second Audio Program Sound Control ButtonsSurrnd Surround Favorite Channel Selection ButtonsControls and Functions Battery Installation InstallationRemote Control Step Procedure For Details, refer to Quick SetupInstallation Overview Ambient Light Installation ConsiderationsWall-Mounting the Crystal Series LCD Display Other ConsiderationsConnections to the Crystal Series LCD Display Antenna/Cable TV ConnectionDVI Connections Refer to Computer/Video Signal Compatibility on page 56 for Analog RGB ConnectionsInput Connection InputLeft Side Connector Pin AssignmentsRS-232 Controller Installation Changing the OSD Language Turning on the PowerOperation Setting the PC Display Properties Using the On-Screen Menus Setup Picture AdjustTimer SourceAspect Ratio Main MenuSource TV Input1 Input2 Input3Aspect Ratio Settings Remote Aspect Ratio Control Description KeyTypical Pluge Pattern for Adjusting Brightness Picture AdjustTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Audio Balance Equalizer Surround Audio Language TV SpeakerTimer On Timer Off Timer Sleep Timer Time Zone TimerChannel Auto Tuning Add/Erase Favorite Channel ChannelCharacteristics of the incoming signal SetupFCC Ratings and Content Categories Rating/Category DescriptionOffensive language ISF Calibration ISF Calibration Picture Adjust White Balance Blue EnableGamma Baud Rate Command Ack Factory Reset Splash Duration Menu should be used by ISF-certified technicians onlyWhite Balance Gain OffsetCrystal Series LCD Display Splash Screen Using Picture-In-Picture PIP Main Button on the remote controlAvailable Main and PIP Source Combinations Aspect Size Position PIP Swap Swap TV/AV Mode Swapping the Main PIP Images Button on the remote controlPIP Audio Programs Swap button on the remote control Compatibility with Stereo and SAP Audio Broadcasts Broadcast Mode Receive Mode Mono StereoStereo Sound/SAP Mono+SAPOperation Troubleshooting Tips Maintenance and TroubleshootingCleaning Troubleshooting ChartComputer/Video Signal Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax Command DescriptionSAB Key 0002 0043 Crystal Series LCD Display Specifications SpecificationsCrystal Series LCD Display Specifications Specifications are subject to change without noticeCrystal Series LCD Display Dimensions CR-26HD DimensionsCR-32HDi Dimensions Computer/Video Signal Compatibility Computer/Video Signal Compatibility ChartPage Runco CL-810 Owner’s Operating Manual

Related manuals

Manual 68 pages 21.6 Kb