Sharp PG-F325W Setting up the Projector Using RS-232C or Telnet, When Connecting Using RS-232C

Page 20

Setting up the Projector Using RS-232C or Telnet

Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on the computer to carry out various settings for the projector.

When Connecting Using RS-232C

1 Launch general purpose terminal emulator.

2 Input settings for the RS-232C port of the terminal emulator as follows.

Baud Rate

: 9600 bps*

Data Length

: 8 bit

Parity Bit

: None

Stop Bit

: 1 bit

Flow Control

: None

*This is the factory default setting. If the value of Baud Rate for the projector has been changed, set Baud Rate here according to the changed value on the projector.

7 Input “setup” and press the “Enter” key.

•SETUP MENU will be displayed.

▼SETUP MENU

---------------------------------

SETUP MENU--------------------------------

 

[1]IP Address

[2]Subnet Mask

[3]Default Gateway

[4]User Name

[5]Password

 

[6]RS-232C Baud Rate

[7]Projector Name

[8]DHCP Client

[A]Advanced Setup

 

[D]Disconnect All

[V]View All Setting

[S]Save & Quit

[Q]Quit Unchanged

setup>

 

 

 

 

 

Note

•User name and password are not set in the fac- tory default settings.

•If the user name or password is entered incor- rectly three times, SETUP MENU will be quit.

3 Input “PJS11234” and press the “Enter” key.

4 “OK” is displayed. Input “PJS25678” and press the “Enter” key within 10 seconds.

5

“User Name:” is displayed. Input the user name and press the “Enter” key.

•If a user name has not yet been set, just press the “Enter” key.

6

“Password:” is displayed. Input the password and press the“Enter”key.

•If a password has not yet been set, just press the “Enter” key.

-20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Setup Manual Connecting Pin Assignments Sub 15 pin female connectorConnecting Pin Assignments Basic format RS-232C Specifications and CommandsComputer control Communication conditions Commands W RDNR BrilliantColorTM OK or ERR PAL Setting up the Projector Network Environment Network settings on the computerConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector DNS Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Confirming the Projector Controlling the ProjectorStatus Status ControlSetting and Adjusting Setting the SecurityProjector Settings & Adjustments Network SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail Originator Settings GeneralMail Recipient Settings Occurs Service & Support Access URLSetting up the Projector Using RS-232C or Telnet When Connecting Using RS-232CWhen Connecting Using Telnet ClickStartfrom theWindows desk- top and select RunSetup Menu Main Menu Advanced Setup MenuSet Items View Setting Detail ListVView All Setting Save Settings and Quit Quit without Saving SetSSave & Quit Tings QQuit UnchangedIP Address Setting Default Gateway SettingSubnet Mask Setting User Name SettingPassword Setting Projector Name SettingDhcp Client Setting RS-232C Baud Rate SetDisconnecting All Connec Setting Auto Logout TimeEntering Advanced Setup Menu Data Port SettingAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Troubleshooting Communication cannot be established with the projectorTroubleshooting \ After the initialization, carry out setting again
Top Page Image Contents