Sharp PG-F325W Troubleshooting, Communication cannot be established with the projector

Page 32

Troubleshooting

Communication cannot be established with the projector

When connecting the projector using serial-connection

\Check that the RS-232C terminal of the projector and a computer or the commercially available controller are connected correctly.

\Check that the RS-232C cable is a cross-over cable.

\Check that the RS-232C port setting for the projector corresponds to the setting for the computer or the commercially available controller.

When connecting the projector to a computer using network (LAN)- connection

\Check that the cable’s connector is firmly inserted in the LAN terminal of the projector.

\Check that the cable is firmly inserted into a LAN port for a computer or a network device such as a hub.

\Check that the LAN cable is a Category 5 cable.

\Check that the LAN cable is a cross-over cable when connecting the projector to a computer directly.

\Check that the LAN cable is a straight-through cable when connecting the projector with a network device such as a hub.

\Check that the power supply is turned on for the network device such as a hub between the projector and a computer.

Check the network settings for the computer and the projector

\Check the following network settings for the projector.

•IP Address

Check that the IP address for the projector is not duplicated on the network.

•Subnet Mask

When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same:

•The subnet masks for the projector and the computer should be the same.

•The IP address parts shown by the subnet mask for the projector and the computer should be the same.

(Example)

When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the subnet mask should be “255.255.255.0”.

•Gateway

When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same:

•The subnets for the projector and the computer should be the same.

•The IP address parts shown by the subnet mask for the projector and the computer should be the same.

(Example)

When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the subnet mask should be “255.255.255.0”.

Note

•When “DHCP Client” is set to “OFF” on the projector IP address : 192.168.150.2

Subnet mask : 255.255.255.0

Gateway address : 0.0.0.0 (Not Used)

•For network settings for the projector, refer to page 13.

-32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Setup Manual Connecting Pin Assignments Sub 15 pin female connectorConnecting Pin Assignments Basic format RS-232C Specifications and CommandsComputer control Communication conditions Commands W RDNR BrilliantColorTM OK or ERR PAL Setting up the Projector Network Environment Network settings on the computerConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector DNS Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Confirming the Projector Controlling the ProjectorStatus Status ControlSetting and Adjusting Setting the SecurityProjector Settings & Adjustments Network SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail Originator Settings GeneralMail Recipient Settings Occurs Service & Support Access URLSetting up the Projector Using RS-232C or Telnet When Connecting Using RS-232CWhen Connecting Using Telnet ClickStartfrom theWindows desk- top and select RunSetup Menu Main Menu Advanced Setup MenuSet Items View Setting Detail ListVView All Setting Save Settings and Quit Quit without Saving SetSSave & Quit Tings QQuit UnchangedIP Address Setting Default Gateway SettingSubnet Mask Setting User Name SettingPassword Setting Projector Name SettingDhcp Client Setting RS-232C Baud Rate SetDisconnecting All Connec Setting Auto Logout TimeEntering Advanced Setup Menu Data Port SettingAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Troubleshooting Communication cannot be established with the projectorTroubleshooting \ After the initialization, carry out setting again
Top Page Image Contents