Sharp PG-D45X3D quick start See bottom of projector

Page 5
U.S.A. ONLY
U.S.A. ONLY

Before using the projector, please read this operation manual carefully.

IntroductionENGLISH

There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notifi cation of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fi re or electric shock, do not expose this product to rain or moisture.

See bottom of projector.

The lightning fl ash with arrowhead sym-

CAUTION

bol, within an equilateral triangle, is in-

tended to alert the user to the presence

RISK OF ELECTRIC SHOCK.

of uninsulated “dangerous voltage”

DO NOT REMOVE SCREWS

within the product's enclosure that may

EXCEPT SPECIFIED USER

be of suffi cient magnitude to constitute

SERVICE SCREW.

a risk or electric shock to persons.

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

The exclamation point within a triangle

DO NOT REMOVE COVER.

is intended to alert the user to the pres-

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

ence of important operating and main-

REFER SERVICING TO QUALIFIED SERVICE

tenance (servicing) instructions in the

PERSONNEL.

literature accompanying the product.

 

WARNING:

 

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

WARNING: FCC Regulations state that any unauthorized changes or modifi cations to this equipment not expressly approved by the manufacturer could

void the user's authority to operate this equipment.

The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verifi cation.

U.S.A. ONLY

Introduction

1

Image 5 Contents
PG-D45X3D Model No Serial No Iii Page See bottom of projector Information Product Disposal For Future Reference Contents Reference Setting up the Projector Network Environment Network MenuPower Sources CleaningAccessories Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Temperature monitor function Using the projector in other countriesOther connected equipment Closed Caption uses Bitstream Vera fontsFor Macintosh When you want to view the Setup ManualFor Windows RCA to mini D-sub 15 pin cable 10 n 3.0 m AccessoriesOptional accessories Projector Adjust leverPart Names and Functions Rear View Using the Carrying HandleUsing the Kensington Lock Button Button32Usable Range Remote control signal transmittersInserting the Batteries Adjust lever Setup and ProjectionQuick Start Zoom ring Focus ringProjector Control Correct trapezoidal distortionVideo Setup Setting up the ProjectorSetting up the Projector Standard Setup Front ProjectionDistance Projection PRJ ModeExample 43 Signal Input Normal Mode Picture Size Screen Size and Projection Distance Signal Input Normal ModeSignal Input Stretch Mode You may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Audio Controlling the Projector by a Computer AC socket Power cord To AC outlet Supplied Connecting the Power CordWhen connecting to the LAN terminal using a LAN cable Turning the Projector On Turning the Projector On/OffAdjusting the Height Adjusting the Projected Image Adjusting the FocusAdjusting the Picture Size Image ProjectionPress P/Q or O/R to adjust Keystone Correction Press Keystone to enter the Keystone Correction modeCorrecting Trapezoidal Distortion Press KeystoneAdjusting the Volume Switching the Input ModeVIDEO, Video buttons AV Mute button VOL +/- Volume buttons On-screen displayPress Resize Resize ModeAbout Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImageWhen moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingPicture menu Menu ItemsScreen adjustment SCR-ADJ menu Help menu n Items you can set with the Help menuMenu Selections Adjustments Using the Menu ScreenPress Q or O and select Picture to adjust Press MENU/HELPPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press EnterMenu operation n Picture Adjustment Picture MenuSelecting the Picture Mode Adjusting the Color Temperature Adjusting the ImageAdjusting the Colors Adjusting Hue, Saturation, or ValueEco+Quiet ProgressiveReducing Image Noise DNR Adjusting the Projected Image SCR ADJ Menu Closed Caption DLP LinkTM DLP LinkTM Invert Setting the Video SetupSelecting the Background Image Reversing/Inverting Projected ImagesAuto Power Off Function Auto Sync Auto Sync AdjustmentStandby Mode Auto Restart FunctionSpeaker Setting Audio Output Type SettingFan Mode Setting Selecting the Transmission Speed RS-232CChecking the Lamp Life Status When the System Lock is setEnter the same keycode in Re- confirm Input screen for keycodeTaking the Keylock off Keylock FunctionLocking the Operation Buttons Select Password, then press Enter or Q Setting a PasswordEnter the same password in Reconfirm, then press Enter On the projector, pressDhcp Client Setting Setting up the Projector Network Environment Network MenuTCP/IP Setting Enter IP Address using P, R, Q O, then press EnterEnter button Adjustment buttons P/R/O/Q MENU/HELP button Troubleshooting with the Help MenuUtilizing the Help Menu Functions Press EnterCleaning the projector MaintenanceCleaning the lens Cleaning the exhaust and intake ventsAbout the lamp indicator Maintenance IndicatorsAbout the temperature warning indicator Red on Abnormally high Are high Lower than 95F +35ºC Replacing the Lamp Regarding the LampLamp Lamp unit Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer Computer Computer Compatibility Chart21-25 Troubleshooting52, 53 For Sharp Assistance PG-D45X3D SpecificationsDimensions Index