Sharp PG-M10X Adjuster Adjustment, Case of RGB input, adjust the video of the connected PC

Page 21

Using the unit

Adjuster Adjustment

There are two adjusters: one on the right side of the back panel and another in the front center of the unit.

1Use right hand to lift the front of the unit to approximately the desired adjustment angle.

2Press the foot release button on the front.

Loosen the foot release and allow it to drop into position.

3Release the button.

The extended foot release will be locked.

4Rotate the contact surfaces of the rear adjuster either clockwise or counterclockwise to accurately adjust the level.

4

Up Down

12

3

Up

Down

6 When distortion of the projected image cannot be corrected with the adjusters, press the KEYSTONE +/– buttons of the remote control to fine adjust (see page 22).

Using KEYSTONE to adjust projected image distortion.

ENLARGE KEYSTONE VOLUME

Maximum correction is 14 degrees (including optical correction).

The top and bottom of the projected image is corrected, as shown below.

If a menu is being displayed, distortion of the menu will not be corrected.

7 Adjust the image size to match the distance to the screen. Next, use the focus ring to adjust the focus.

Focus ring

8 Change the unit setting to suit the method and source selected in step 4.

•Select the “PROJECTION” appropriate for the type of projector installation. (See page 33)

If the image is projected reversed, vertically, or horizontally, reset “PROJECTION”.

•In the case of video or S-video, select the color system as necessary. (See page 30)

Normally, it is not necessary to change the factory settings. Also, set the COMPUTER input terminal for YPBPR (component video). (See page 31)

•In the case of RGB input, adjust the video of the connected PC.

This unit automatically identifies the input signal and selects the most appropriate resolution. However, manually adjust the “CLOCK” and “PHASE” (see page 28) when there is flicker, noise, color offset, etc., and manually adjust the vertical and horizontal position (see page 28) when the image is not centered.

You can maintain the original aspect ratio of the incoming signal. (see page 31). (Normally, the resolution is automatically detected and the display is enlarged or reduced.)

9 Adjust the picture elements (see page 26), then select the picture type according to the video content (see page 30).

10 Start using the unit.

The following functions are available while using the unit:

•Adjusting the volume of the unit's speaker (see pages 22 and 32),

•Turning off the image and muting the sound temporarily (see page 22),

•Freezing a moving picture (see page 22),

•Enlarging the picture (see page 23)

When there is no signal input for a period of 5 min. or more, the power is automatically turned off and standby status is activated.

Basic Operation

19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PG-M10X PG-M10S Special Note for Users in the U.K English For Netherlands Only Accessories CleaningPower Sources Power-Cord ProtectionPower Supply InstallationLamp Replacement Fire and Shock PrecautionsContents For Sharp Assistance U.S.A. only Usage GuidelinesMain Features You’ll Enjoy FeaturesRemote control that can operate the PC Compatible with following various color systemsFor remote control Supplied AccessoriesWhen using the remote control as computer mouse For video equipment connectionRemote control effective range Preparing the Remote ControlPress firmly and slide the battery cover off Slide the battery cover back until it snaps into placeTop, front side panel view Control panel Part NamesBottom Speaker 15Terminal Panel Rear and side panel viewPart Names Mouse terminal Video input terminalRemote Control 22 , 24 Flip Cover Remote control signal transmitterEnter button Positioning the unit InstallationTip Projecting distance and image sizeReversed Image Setup Projection using a mirrorRear projection Connections Connecting video equipmentConnection to the Video input terminal of the unit Connection to the S-VIDEO input terminal of the unitConnecting a PC or Macintosh Connection to the Computer input terminalRear panel terminals of this unit Receiving Video Output from Personal Computers Changing the computer’s video resolutionsWindows 98/Windows WindowsConnect the power cord Using the unitAdjust the position and height of the unit When the projected image is offset verticallyAdjuster Adjustment Case of RGB input, adjust the video of the connected PCUsing the unit After using the unit Using the Remote Control Input SelectionUsing the Remote Control Input Selection Operating from the main unitUsing the Remote Control as the PC Mouse Remote control mouse functionsConnecting a PC and the Mouse terminal of this unit Various functions while using the unit Enlarging the picture To move to the desired portion of the enlarged pictureScreen Reduction Menu Structure Menu operationMenu button Common menuRGB input Menu operationAdjusting the picture elements For VIDEO, S-VIDEO and component video Ypbpr inputTo close the menu Timing Chart Adjusting the projected image from the computerResolution Sync. kHz Sync. Hz IBM PC/AT compatible machine Apple MacintoshAdjusting Clock Frequency and Phase Manual Adjustment of Personal Computer ImagesAdjusting the position of the image If no images appear during settingResetting Resetting the factory defaultsResetting the Lamp Usage Timer Setting the Video Type Advanced Menu SettingsAdjusting Color Balance Selecting the Color SystemSetting the Computer input terminal Setting in Accordance With Image ContentSetting the Display Frame Setting FilterInitial Settings Using the Power Saving Function Auto Source SettingsInitial Settings Selecting a Projection FormatSelecting the Menu Language Other Menu Settings Setting the Menu OptionSetting the Menu Display Position Menu Viewing SettingsPlease check the following before requesting repairs TroubleshootingWhen the Status Indicator Illuminates or Flashes Status Light MessagesCondition Status Replacing the Projection Lamp Removing and installing the lamp unitHow to use the carrying bag Using the Carrying BagTransporting the Projector Out To the carrying bagReplacement parts SpecificationsSub Pin Assignments DimensionsGuide to Effective Presentations Types of PresentationsCreative Presentations Guide to Effective Presentations FontsGuide to Effective Presentations Good Bad Set-UpPresentation Tips Rehearsing & DeliveryGlossary Enlarge button IndexSharp Corporation

PG-M10X specifications

The Sharp PG-M10X is a compact and versatile portable projector that caters to the needs of business professionals, educators, and casual users alike. With its lightweight design and robust feature set, the PG-M10X is well-suited for both small meetings and larger presentations, ensuring that users have a reliable solution for various display needs.

One of the standout features of the Sharp PG-M10X is its resolution. It typically offers a native SVGA (800 x 600) resolution, which is ideal for standard presentations and slide shows. This resolution allows for clear and vibrant images, making text and graphics easy to read and comprehend. While it may not match the ultra-high-definition projectors available today, the PG-M10X performs exceptionally well in environments where high clarity is needed without requiring a significant investment.

The projector boasts a brightness level of approximately 2,200 ANSI lumens. This level of brightness is particularly effective in slightly lit rooms, as it ensures that images remain visible and sharp even in challenging lighting conditions. The PG-M10X also features a contrast ratio of 400:1, enhancing the depth of images, thereby making visuals more engaging during presentations.

In terms of connectivity, the Sharp PG-M10X offers a range of ports, including HDMI, VGA, and composite inputs, allowing users to easily connect various devices such as laptops, DVD players, and gaming consoles. This flexibility makes the projector an ideal choice for mixed-media presentations or classroom settings.

Another significant advantage of the PG-M10X is its 2-in-1 projection capability, enabling both front and rear projection without any hassle. This feature is especially useful in versatile setups where the projection surface might require adjustments based on audience layout.

The projector’s lamp life extends up to 4,000 hours in standard mode, allowing for an extended usage period before requiring a replacement. This extended lifespan minimizes maintenance costs and maximizes convenience for users who require frequent access.

Additionally, the PG-M10X incorporates innovative cooling technology, which ensures quiet operation by reducing fan noise during presentations. This consideration significantly enhances the viewing experience, allowing audiences to focus on the content rather than distracting background noises.

In conclusion, the Sharp PG-M10X delivers a well-rounded set of features that cater to various projection needs. Its reliability, ease of use, and versatility make it a preferred option for anyone looking to enhance their visual presentations effectively. Whether in the boardroom or the classroom, the PG-M10X stands ready to be a dependable projection partner.
Top Page Image Contents