![](/images/new-backgrounds/1143664/143664131x1.webp)
Chapter 4
SpeedTouch™ Web Interface
4.5.2 Game & Application Sharing
Overview The Overview page summarizes the applications or games installed on a particular local host on your network, for which the SpeedTouch™ should accept inbound initiated connections coming from the Internet.
Configure On the Configure page, you can:
Select Use UPnP to enable UPnP on the SpeedTouch™.
UPnP provides NAT-Traversal: UPnP aware applications on a PC will automatically create Hyper-NAT entries on the SpeedTouch™ for incoming traffic on the protocol ports this type of traffic needs. As a consequence these applications are able to traverse the SpeedTouch™ without the need for extra and manual configuration.
UPnP is an architecture for transparent peer-to-peer connectivity of computers, intelligent appliances, and (wireless) devices. It enables seamless operation of a wide range of games and messaging applications.
For security reasons you are able to configure the UPnP policy towards
Windows XP and UPnP aware applications and Operating Systems.
In case you select the Use Extended Security check box, only limited UPnP operation between a host running MS Windows XP and the SpeedTouch™ is allowed: A local host is:
NOT allowed to connect/disconnect the SpeedTouch™ Internet Gateway
Device (IGD) connection.
Allowed to add/delete Hyper-NAT entries only for its own IP address, not for other local hosts.
If you clear the Use Extended Security check box, all UPnP- and IGD-based communication between any local host and the SpeedTouch™ is allowed.
58 | E-DOC-CTC-20051017-0147 v2.0 |
|
SpeedTouch585v6
Page
SpeedTouch
Copyright
Trademarks
Document Information
Contents
SpeedTouch Web Interface
Troubleshooting
Contents
Terminology Documentation and software updates
About this User’s Guide
About this User’s Guide
Getting to know your SpeedTouch
Indicator Description Name Colour State
SpeedTouch LED Behaviour
Indicator Description Name LED Status
DSL
Accessing your SpeedTouch
Access Method Can be used to
Access via the Web Interface
To access the SpeedTouch via the Web interface
Access via CLI
To access the SpeedTouch via the Command Line Interface CLI
For more information, see Quote site command on
Select All Programs Accessories Command Prompt
To start a Telnet session
Access via FTP
Open a Command Prompt window
Common FTP commands
Use Command
Ftp quote site ip iplist
To access the SpeedTouch remotely To enable remote access
To disable remote access
Remote Assistance
Chapter
Local Network Setup
Wired Ethernet Wireless Ethernet
Wired Ethernet
For more information, see Device settings on
Wireless Ethernet
Introduction Wireless client requirements
Wireless Basics
Chapter
Connecting Wireless Clients for the First Time
Wireless default settings
Wireless Security on
First-time association example
Click Connect Anyway
Wireless Security
Name Ssid
WEP Wired-Equivalent Privacy
Search for wireless devices task
Security disabled default
WPA-PSK Wi-Fi Protected Access Pre-Shared Key
Click Configure
Connecting Additional Wireless Clients
Security issues Registering wireless clients
Registering clients via Web pages
Registering clients via the association button
Extending the Range of Your Wirelstess Network
Wireless Distribution System WDS
Chapter
Chapter
Web Pages
Internet Connectivity Dial-In Clients
SpeedTouch
Internet Gateway
If your computer runs You can use
See 3.1 SpeedTouch Web Pages on page 31 to proceed
SpeedTouch Web Pages
Introduction Starting an Internet session
Monitoring your Internet connection
Terminating an Internet session
Internet Gateway Device Control Agent
Internet connection status Terminating an Internet session
SpeedTouch Web Interface
SpeedTouch Consult Documentation
Navigation
Menu Language Bar Navigation Bar Notification Area Tasks
Menu
Collapsing
Expanding the menu
Language Bar
Navigation Bar
Notification Area
Tasks
Home
SpeedTouch home
SpeedTouch Broadband Connection Toolbox Home Network
Information Configuration Event Logs
SpeedTouch
Information
SpeedTouch Easy Setup
SpeedTouch
Restart
Restarting your
Click Yes, restart my SpeedTouch. The SpeedTouch restarts
Configuration
Saving your current configuration
Back up & Restore
Accessing the Backup & Restore
Restoring a previously saved configuration
Reset to Factory Defaults
Resetting the SpeedTouch factory defaults
Indicator Description
Event Logs
DSL Connection Internet Services
Broadband Connection
Broadband Connection menu
Connectivity Check
Pick a task list, click Check connectivity to the Internet
Click Check Connectivity
DSL Connection
Internet Services
Internet Service Settings
Accessing the Internet Service Settings Overview
Broadband Connection menu, click Internet Services
Toolbox
Username Password
Enabling Remote Assistance
Terminating remote assistance
Game & Application Sharing
Chapter
Accessing the Defined Games & Applications
Defined Games & Applications
Game or Application Definition
Accessing the Game or Application Definition Overview
Configure Under
Adding a Port Translation rule
New Game or Application
Creating a new game or application
Parental Control
Current Address Based Filtering rules
Redirect a Web site Proceed as follows
Deny access to a specific Web site
Allow access to a specific Web site
Allow is selected under Action for Unknown Sites
Redirecting all Web sites
Configure content based filtering settings
Under Content Based Filtering you can
Click Redirect in the Action list
Toolbox menu, click Web Site Filtering Click Configure
Content Level
Accessing the Content Level
Icon Description
BlockAll
Disabled
Firewall
Standard
Details of a security level
Creating a new security level
Editing a security level Proceed as follows
Chapter
Intrusion Detection
On the Dynamic DNS page, click Configure
Dynamic DNS
User Management
User Privileges
Chapter
Edit User
Editing a user account Proceed as follows
Toolbox menu, click User Management
Change Default User
Changing the default user
Change Default User page appears
Add User
Home Network
Devices
Interfaces
Home Network Viewing wireless client information
See 4.6.2 Device Settings on page 80 for more information
Devices
Device Settings
Accessing the device settings Overview
Connection Sharing
Chapter
Assign Public IP
Assigning the public IP address to a device
Wireless Device Settings
Accessing the wireless device settings Overview
Access Point Settings
Accessing the Access
Point settings
Encryption
Broadcast Network Name
Allow New Devices
Select Use WEP Encryption
New stations are allowed automatically
Access control on SpeedTouch
Select Use WPA-PSK Encryption
New stations are allowed via registration
Information, see 4.6.4 Wireless Device Settings on
Pick a task list, click Scan for wireless Access Points
Configuring WDS
Click Configure Pick a task list, click Configure WDS
Establishing a WDS connection
Interfaces
Interface Settings
Assigning a new IP address to the SpeedTouch
Dhcp Pool Accessing the Dhcp Pool
Dhcp Pool
Home Network menu, click Interfaces
Components Dhcp Pool
Troubleshooting
Poor SpeedTouch
General SpeedTouch Troubleshooting
SpeedTouch does not work SpeedTouch unreachable
Performance
Wired Ethernet Troubleshooting
LANLEDdoesnotlightup Make sure that
Wireless Ethernet Troubleshooting
Not able to connect wireless clients
UPnP on Windows XP Systems
Adding IGD Discovery Control
Resetting your SpeedTouch
Software reset Hardware reset
100
Page
Need more help?