Sharp XV-Z15000 operation manual Maintenance Indicators, About the temperature warning indicator

Page 50

Maintenance Indicators

The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.

If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below.

Top View

Power indicator

Lamp indicator

Temperature warning indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising,

” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter standby mode. When you find the temperature warning indicator blinking, be sure to perform the measures described on page 49.

About the lamp indicator

When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate in red.

If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.

Indicators on the Projector

Power indicator

Red on

Normal (Standby)

 

Green on

Normal (Power on)

 

 

 

 

Red blinks

Abnormal (See page 49.)

 

 

 

 

Green blinks

Normal (Cooling)

 

 

 

 

Green and orange blink

The lens shutter is closed. (See page 22.)

 

alternately

 

Lamp indicator

Green on

Normal

 

Green blinks

The lamp is warming up.

 

Red on

The lamp is shut down abnormally or requires to be changed. (See

 

 

page 49.)

Temperature warning

Off

Normal

indicator

 

 

Red on/Red blinks

The internal temperature is abnormally high. (See page 49.)

 

 

 

-48

Image 50
Contents XV-Z15000 Special Note for Users in the U.K Introduction See bottom of projectorInformation Declaration of conformityContents Info Indicates safeguards for using the projector Buttons used in this operationPower-Cord Protection CleaningAccessories Damage Requiring ServiceDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Other connected equipment Using the projector in other countriesTemperature monitor function Optional accessories AccessoriesSupplied accessories Part Names and Functions ProjectorProjector Rear View TerminalsRemote Control HDMI1, 2, Component VIDEO, Video23 7 m Remote control sensors Using the Remote ControlWhen using the remote control Inserting the BatteriesQuick Start Place the projector facing a screenTurn the power off Select the input modeAdjust the projector angle, focus and zoom Turn the video equipment on and start playbackStandard Setup Front Projection Setting Up the ProjectorSetting Up the Projector Example of standard setupPicture Size Projection PRJ ModeCeiling-mount Setup 174Screen Size and Projection Distance You may need other cables or connectors not listed below Samples of Cables for ConnectionConnecting to Video Equipment Connecting to Equipment with S-video Output TerminalConnecting to a Computer Connecting to a Computer Using the RGB CableFor details on RS-232C specifications and commands, see Controlling the Projector by a ComputerDirect Power Off function Connecting the Power CordAbout the Lamp Indicator Turning the Projector On/OffAdjusting the Picture Size Adjusting the Projected ImageAdjusting the Focus Adjusting the HeightKeystone Correction Press Keystone to enter the keystone modePress P/R/O/Q to adjust Keystone Correction Press KeystoneAuto V-Keystone Correction Press P/R/O/Q to adjust Sphere Correction modePress P/R/O/Q to adjust the Rotation Correction mode Press P/R to select SPHERE, and then press EnterPress Image Shift to enter the image shift mode Switching the Input ModeAdjusting the Vertical Horizontal Position Image Image ShiftDisplaying the Black Screen Temporarily Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImagePress Magnify on the remote control Switching the Iris SettingSwitching the Eco+Quiet Mode Displaying an Enlarged Portion of an ImageResize Mode Resize ModePress Resize on the projector or on the remote control Resize buttonAbout Copyrights Menu Bar Items Picture menuSIG-ADJ menu SCR-ADJ menu Using the Menu Screen Menu Selections Adjust- mentsPress or \ to adjust the item selected To adjust the projected image while viewing itPress or to select the item you want to adjust Press Enter2Adjusting the Image Picture Adjustment Picture Menu1Selecting the Picture Mode 7Adjusting the Colors 3Switching the Iris Setting5Using the Advanced 4Eco+QuietS. color adjustment screen 0Setting Detail Enhancement 8Adjusting the Bright Boost9Selecting the Film Mode EResetting All Adjustment Items1Adjusting the Computer Image Computer Image Adjustment SIG-ADJ Menu3Auto Sync Auto Sync Adjustment 2Setting the Resolution8Signal Info 5Setting the Video System7Adjusting the Dynamic Range 6Setting the Video Setup2Adjusting the Image Position Adjusting the Projected Image SCR-ADJ Menu1Setting the Resize Mode 3Adjusting the OverscanOr Q 5Keystone Mode Correction4Auto V-Keystone Correction 8Selecting the Background Image 6Setting On-screen Display7Setting the Brightness Menu Screen 9Selecting the Menu Screen Position 1Setting Auto Power Off Mode Adjusting the Projector Function PRJ-ADJ Menu 3Setting One Touch Play, System Standby and Input Name 2Setting the Power Save Mode Economy Mode7Returning to the Default Settings 4Setting the Demo Mode6Fan Mode Setting 8Lamp Timer LifeCleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsAbout the lamp indicator Maintenance IndicatorsAbout the temperature warning indicator Indicators on the ProjectorNot illuminate Down Outlet, and then connect it again Replacing the Lamp Regarding the LampLamp Removing and Installing the Lamp Unit Remove the lamp unit coverResetting the Lamp Timer Computer Input/Output Connecting Pin AssignmentsHdmi Terminal Component Input/OutputRS-232C Specifications and Commands Computer controlERR ERR OK, ERR Computer Compatibility Chart ComputerTroubleshooting Problem CheckReplace the lamp For Sharp Assistance Specifications HdmiDimensions Units inches mmIndex Sharp Corporation
Related manuals
Manual 66 pages 7.72 Kb