Sharp XV-Z15000 operation manual Regarding the Lamp, Replacing the Lamp

Page 52

Regarding the Lamp

Lamp

■It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page 46.)

■Purchase a replacement lamp of type AN-K15LP from your place of purchase, nearest Sharp Autho- rized Projector Dealer or Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho- rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP

U.S.A. ONLY

Caution Concerning the Lamp

■This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time.

■The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■Should the lamp break, there is also a possibility that glass particles may spread inside of the projec- tor. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.

■Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mer- cury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

Caution

•Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury.

•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

■Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

*If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair.

-50

Page 51 Page 53
Image 52
Page 51 Page 53
Contents XV-Z15000 Special Note for Users in the U.K Introduction See bottom of projectorInformation Declaration of conformityContents Info Indicates safeguards for using the projector Buttons used in this operationCleaning AccessoriesPower-Cord Protection Damage Requiring ServiceRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Supplied accessories AccessoriesOptional accessories Part Names and Functions ProjectorProjector Rear View TerminalsRemote Control HDMI1, 2, Component VIDEO, VideoUsing the Remote Control When using the remote control23 7 m Remote control sensors Inserting the BatteriesQuick Start Place the projector facing a screenSelect the input mode Adjust the projector angle, focus and zoomTurn the power off Turn the video equipment on and start playbackSetting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Example of standard setupProjection PRJ Mode Ceiling-mount SetupPicture Size 174Screen Size and Projection Distance You may need other cables or connectors not listed below Samples of Cables for ConnectionConnecting to Video Equipment Connecting to Equipment with S-video Output TerminalConnecting to a Computer Connecting to a Computer Using the RGB CableFor details on RS-232C specifications and commands, see Controlling the Projector by a ComputerConnecting the Power Cord About the Lamp IndicatorDirect Power Off function Turning the Projector On/OffAdjusting the Projected Image Adjusting the FocusAdjusting the Picture Size Adjusting the HeightPress Keystone to enter the keystone mode Press P/R/O/Q to adjust Keystone CorrectionKeystone Correction Press KeystonePress P/R/O/Q to adjust Sphere Correction mode Press P/R/O/Q to adjust the Rotation Correction modeAuto V-Keystone Correction Press P/R to select SPHERE, and then press EnterSwitching the Input Mode Adjusting the Vertical Horizontal Position ImagePress Image Shift to enter the image shift mode Image ShiftAuto Sync Auto Sync Adjustment Selecting the Picture ModeDisplaying the Black Screen Temporarily Freezing a Moving ImageSwitching the Iris Setting Switching the Eco+Quiet ModePress Magnify on the remote control Displaying an Enlarged Portion of an ImageResize Mode Press Resize on the projector or on the remote controlResize Mode Resize buttonAbout Copyrights Menu Bar Items Picture menuSIG-ADJ menu SCR-ADJ menu Using the Menu Screen Menu Selections Adjust- mentsTo adjust the projected image while viewing it Press or to select the item you want to adjustPress or \ to adjust the item selected Press Enter1Selecting the Picture Mode Picture Adjustment Picture Menu2Adjusting the Image 3Switching the Iris Setting 5Using the Advanced7Adjusting the Colors 4Eco+QuietS. color adjustment screen 8Adjusting the Bright Boost 9Selecting the Film Mode0Setting Detail Enhancement EResetting All Adjustment ItemsComputer Image Adjustment SIG-ADJ Menu 3Auto Sync Auto Sync Adjustment1Adjusting the Computer Image 2Setting the Resolution5Setting the Video System 7Adjusting the Dynamic Range8Signal Info 6Setting the Video SetupAdjusting the Projected Image SCR-ADJ Menu 1Setting the Resize Mode2Adjusting the Image Position 3Adjusting the Overscan4Auto V-Keystone Correction 5Keystone Mode CorrectionOr Q 6Setting On-screen Display 7Setting the Brightness Menu Screen8Selecting the Background Image 9Selecting the Menu Screen PositionAdjusting the Projector Function PRJ-ADJ Menu 3Setting One Touch Play, System Standby and Input Name1Setting Auto Power Off Mode 2Setting the Power Save Mode Economy Mode4Setting the Demo Mode 6Fan Mode Setting7Returning to the Default Settings 8Lamp Timer Life Maintenance Cleaning the projector Cleaning the lens Cleaning the exhaust and intake ventsMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Indicators on the ProjectorNot illuminate Down Outlet, and then connect it again Lamp Regarding the LampReplacing the Lamp Removing and Installing the Lamp Unit Remove the lamp unit coverResetting the Lamp Timer Connecting Pin Assignments Hdmi TerminalComputer Input/Output Component Input/OutputRS-232C Specifications and Commands Computer controlERR ERR OK, ERR Computer Compatibility Chart ComputerTroubleshooting Problem CheckReplace the lamp For Sharp Assistance Specifications HdmiDimensions Units inches mmIndex Sharp Corporation
Related manuals
Manual 66 pages 7.72 Kb
Top Page Image Contents