Sharp XV-Z15000 operation manual Removing and Installing the Lamp Unit, Remove the lamp unit cover

Page 53

Removing and Installing the Lamp Unit

•Do not remove the lamp unit from the projector right after use. The lamp and parts Warning! around the lamp will be very hot and may cause burns or injury.

Info

•Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

Optional	Lamp unit
accessory	AN-K15LP

STANDBY/ON button

1 Press STANDBY/ON on the projector or STANDBY on the remote control to put the projec- tor into standby mode.

2 Disconnect the power cord.

• Unplug the power cord from the AC socket.

• Leave the lamp until it has fully cooled down (about 1 hour).

3 Remove the lamp unit cover.

• Close the lens shutter. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

AC socket

User service screw (for lamp unit cover)

Appendix

-51

Image 53

Contents XV-Z15000 Special Note for Users in the U.K See bottom of projector IntroductionDeclaration of conformity InformationContents Buttons used in this operation Info Indicates safeguards for using the projectorAccessories CleaningPower-Cord Protection Damage Requiring ServiceDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Other connected equipment Using the projector in other countriesTemperature monitor function Optional accessories AccessoriesSupplied accessories Projector Part Names and FunctionsTerminals Projector Rear ViewHDMI1, 2, Component VIDEO, Video Remote ControlWhen using the remote control Using the Remote Control23 7 m Remote control sensors Inserting the BatteriesPlace the projector facing a screen Quick StartAdjust the projector angle, focus and zoom Select the input modeTurn the power off Turn the video equipment on and start playbackSetting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Example of standard setupCeiling-mount Setup Projection PRJ ModePicture Size 174Screen Size and Projection Distance Samples of Cables for Connection You may need other cables or connectors not listed belowConnecting to Equipment with S-video Output Terminal Connecting to Video EquipmentConnecting to a Computer Using the RGB Cable Connecting to a ComputerControlling the Projector by a Computer For details on RS-232C speciﬁcations and commands, seeAbout the Lamp Indicator Connecting the Power CordDirect Power Off function Turning the Projector On/OffAdjusting the Focus Adjusting the Projected ImageAdjusting the Picture Size Adjusting the HeightPress P/R/O/Q to adjust Keystone Correction Press Keystone to enter the keystone modeKeystone Correction Press KeystonePress P/R/O/Q to adjust the Rotation Correction mode Press P/R/O/Q to adjust Sphere Correction modeAuto V-Keystone Correction Press P/R to select SPHERE, and then press EnterAdjusting the Vertical Horizontal Position Image Switching the Input ModePress Image Shift to enter the image shift mode Image ShiftSelecting the Picture Mode Auto Sync Auto Sync AdjustmentDisplaying the Black Screen Temporarily Freezing a Moving ImageSwitching the Eco+Quiet Mode Switching the Iris SettingPress Magnify on the remote control Displaying an Enlarged Portion of an ImagePress Resize on the projector or on the remote control Resize ModeResize Mode Resize buttonAbout Copyrights Picture menu Menu Bar ItemsSIG-ADJ menu SCR-ADJ menu Menu Selections Adjust- ments Using the Menu ScreenPress or to select the item you want to adjust To adjust the projected image while viewing itPress or \ to adjust the item selected Press Enter2Adjusting the Image Picture Adjustment Picture Menu1Selecting the Picture Mode 5Using the Advanced 3Switching the Iris Setting7Adjusting the Colors 4Eco+QuietS. color adjustment screen 9Selecting the Film Mode 8Adjusting the Bright Boost0Setting Detail Enhancement EResetting All Adjustment Items3Auto Sync Auto Sync Adjustment Computer Image Adjustment SIG-ADJ Menu1Adjusting the Computer Image 2Setting the Resolution7Adjusting the Dynamic Range 5Setting the Video System8Signal Info 6Setting the Video Setup1Setting the Resize Mode Adjusting the Projected Image SCR-ADJ Menu2Adjusting the Image Position 3Adjusting the OverscanOr Q 5Keystone Mode Correction4Auto V-Keystone Correction 7Setting the Brightness Menu Screen 6Setting On-screen Display8Selecting the Background Image 9Selecting the Menu Screen Position3Setting One Touch Play, System Standby and Input Name Adjusting the Projector Function PRJ-ADJ Menu1Setting Auto Power Off Mode 2Setting the Power Save Mode Economy Mode6Fan Mode Setting 4Setting the Demo Mode7Returning to the Default Settings 8Lamp Timer LifeCleaning the projector MaintenanceCleaning the lens Cleaning the exhaust and intake vents About the temperature warning indicator Maintenance Indicators About the lamp indicator Indicators on the ProjectorNot illuminate Down Outlet, and then connect it again Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitResetting the Lamp Timer Hdmi Terminal Connecting Pin AssignmentsComputer Input/Output Component Input/OutputComputer control RS-232C Speciﬁcations and CommandsERR ERR OK, ERR Computer Computer Compatibility ChartProblem Check TroubleshootingReplace the lamp For Sharp Assistance Hdmi SpeciﬁcationsUnits inches mm DimensionsIndex Sharp Corporation

Related manuals

Manual 66 pages 7.72 Kb