Care and Maintenance
Troubleshooting Tips | TAPE OUT and REC OUT do not operate in VCR mode. |
|
Receiver/Tuner Operation | • Check to make sure the unit is not in | EN |
input mode. | ||
ST indicator is off. | Cleaning the Exterior |
|
•Adjust the antenna.
•Press DIGITAL INPUT/ST/MONO button to insure you are not outputting in mono.
The signal is Mono. Severe hum or noise.
•The signal is too weak. Connect an external antenna.
•Adjust Antenna
•Reposition Antenna away from any electronics.
Remote Control Operation
The remote control does not operate the unit.
•Another source mode is selected on the remote. Press the correct Source Button.
•No batteries installed. (included with your system) Install the batteries before attempting to operate the remote. Be sure to match the + and - ends of each bat- tery to the symbols shown in the remote battery com- partment.
•The batteries are weak. Replace all batteries.
•The remote is not pointed at the remote control sen- sor on the main unit or there is an obstacle between the remote and the main unit.
•The remote control is too far from the main unit, move closer.
Remote loses Programmed codes.
• Weak batteries, replace batteries.
Remote forgets what source was selected.
• Weak batteries, replace batteries.
General
No audio.
•Make sure the speakers are connected.
•Check the input connections.
•Check the power cord connections.
•Make sure the MUTE signal on the front panel is off.
•Make sure the digital setting (optical, coaxial or ana- log) is correct.
•Check that the headphone is not inserted.
No audio from one channel.
•Check the speaker level setting.
•Check the speaker wire or external source cable con- nections.
Noise occurs when the TV is turned on.
• The TV is too close to the audio system.
Specific instruments sound displaced.
•Check the connections between the receiver and the speakers if the sound does not match the video.
•Check if the video and audio cable are correctly inserted.
•Disconnect the system from AC power before cleaning the exterior of the system with a soft dust cloth, or with a slightly damp leather chamois. Never use strong solvents.
Equipment Specifications:
AMPLIFIER SECTION:
RT2600
All 5 channels: each 100W at 8 ohm. <0.9% THD @40Hz to 20KHz
Subwoofer channel: 150w at 8Ω , <0.9% THD @100 Hz
Muting Attenuation: 65dB
Frequency Response: 40Hz to 20kHz
Signal to Noise Ratio: 65dB (Dolby digital mode mode)
RT2350/RT2350BK
All 5 channels: each 50W at 8 ohm. <10% THD @1 kHz
Subwoofer channel: 50w at 8Ω , <10% THD @100 kHz
Muting Attenuation: 65dB
Frequency Response: 40Hz to 20kHz
Signal to Noise Ratio: 65dB (Dolby digital mode mode)
VIDEO SECTION:
Input ( Sensitivity/ Impedance
Crosstalk @3.58MHz: 40dB
AM TUNER SECTION:
Frequency Response: 80Hz – 2kHz
Usable Sensitivity: 800uV/m @ S/N 20dB
Signal to Noise: 38dB
Image Ratio: 27dB @ 1000kHz
IF Rejection: 35dB
FM TUNER SECTION:
Frequency Response: 40Hz – 15kHz
Quieting: 24dBu
Signal to Noise: 60dB(stereo) / 65dB(mono)
Image Ratio: 40dB
IF Rejection: 50dB
Dimensions (H x W x D inch) :
Unit - 5.1 x 17 x 16.5
Speaker - 6.9 x 4.6 x 4.5
Subwoofer - RT2350/RT2350BK:14 x 6.3 x 14 RT2600: 14 x 7.8 x 14.2
23