Noption

MENU .

Menu Items

STANDBY MODE

When STANDARD is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed in standby mode.

When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the startup time from standby mode becomes longer.

If set to LOW POWER, certain RS-232C commands cannot be used in standby mode, and control via LAN will be disabled.

OFF IF NO OPERATION

Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit, RS-232C commands, or LAN for over 4 hours.

HOT PLUG CONTROL

Sets whether to use hot plug control for the PC/AV HDMI and PC/AV DVI-D input terminals.

RS-232C/LAN SELECT

Selects the method with which to control the monitor from

the computer.

ID No. SET

Assigns ID numbers to monitors connected in a daisy chain (see page 30), using the RS-232 cables.

The numbers 1 to 255 are available for ID numbers.

If “0” is set, the system regards this as the state where no ID number is set.

AUTO ASSIGN ID No.

ID No. to be used will be automatically assigned when multiple monitors are connected with RS-232C.

Select ON, then press MENU .

Perform operations using the first monitor in the daisy chain.

BAUD RATE

Selects the communication speed used for RS-232C communication.

LAN SETUP

Configures the settings to control the monitor from the computer via LAN. (See page 41.)

AUTO ASSIGN FIXED IP ADDR.

Can be enabled when RS-232C/LAN SELECT is LAN and the DHCP client is OFF.

Set DHCP CLIENT to OFF for the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows. Fixed IP addresses are automatically allocated.

If the IP address is a duplicate with a network device other than a monitor, individually change the IP address.

SPEAKER SELECT

Selects the speaker to be used.

HDMI AUTO VIEW

When ON is selected, the screen size is adjusted automatically according to the screen size control signal included in the video signal input from the AV HDMI input terminal.

COPY SETTING VALUE

When the monitor has been connected to multiple monitors by RS-232C, the settings in the monitor can be copied to the monitor connected to the RS-232C output terminal and to the daisy chain of connected monitors that follows.

Selects the settings to copy with COPY SETTING VALUE TARGET.

“PICTURE” ONLY	Copies the PICTURE menu settings.*
ALL	Copies all the settings.*

Select the ID No. of the monitor that you would like copy to with COPY TO ID No., then select COPY and press

If you select ALL, settings will be copied to all monitors. When you would like to confirm the ID No. that is set to the

monitor, select ID No. DISPLAY and press . The ID No. will be displayed on the screen.

*Certain setting details such as ANALOG GAIN, ANALOG OFFSET, and DISPLAY COLOR PATTERN cannot be copied.

LOGO SCREEN

Sets whether or not to display the logo screen.

DATE/TIME SETTING

Set the date and time. Press or to select the date

and time, and press or to change the numerical values.

Set the date in “Month/Day/Year” order.

Set the time on a 12-hour basis. (Factory default)

DATE/TIME FORMAT

Sets the date/time display format.

DATE...................MM/DD/YYYY

	DD/MM/YYYY
	YYYY/MM/DD
	(YYYY: Year, MM: Month, DD: Day)
TIME	....................Select 12- or 24-hour time.

SCHEDULE (See page 26.)

You can turn the power on/off and change the screen brightness at a specified time.

INPUT SELECT

Select the input mode to be used in PC D-Sub input terminal, PC/AV DVI-D input terminal, PC/AV HDMI input terminal and PC RGB/AV component input terminals.

For D-SUB, select SET after selecting the input mode, and then press MENU .

D-SUB and BNC cannot be set to AV COMPONENT at the same time.

If D-SUB is set to AV VIDEO, the AV VIDEO input terminal cannot be used for BNC.

AUDIO SELECT

Selects the terminal used to input audio signals in each input mode.

INPUT SIGNAL (PC D-SUB/PC RGB)

If a computer connected to the PC D-sub/PC RGB input terminal outputs any of the following resolutions, make a selection from the following options.

480 LINES	AUTO, 640x480 or 848x480
768 LINES	AUTO, 1024x768, 1280x768, or 1360x768
1050 LINES	1400x1050 or 1680x1050

ZOOM2 SPECIAL SETTING (See page 25.)

E22

PNE802, PN-E802 specifications

The Sharp PN-E802 and its variant, PNE802, represent the pinnacle of professional display technology, designed to meet the demanding needs of various commercial environments. With a massive 80-inch diagonal screen, these displays offer an immersive visual experience, making them ideal for use in meeting rooms, conference halls, retail spaces, and control rooms.

One of the key features of the Sharp PN-E802 is its 4K Ultra HD resolution, providing stunning clarity and detail. With a resolution of 3840 x 2160 pixels, images and text appear razor-sharp, allowing viewers to see every detail, which is essential for presentations and video content. The widescreen aspect ratio enhances the cinematic experience, ideal for videos and detailed graphics.

Equipped with advanced LCD technology, the PN-E802 showcases vibrant colors and deep blacks, further enhanced by Sharp's proprietary UV2A technology. This technology improves color accuracy and enhances brightness, ensuring that images remain vivid even in well-lit environments. The display supports a wide color gamut, encompassing a broader range of colors to produce more accurate and lifelike images.

Moreover, the PN-E802 boasts an integrated digital signage function, making it suitable for dynamic content displays. Users can easily manage and update content via a USB connection, allowing for seamless integration into existing systems. This feature is particularly useful for businesses that need to display rotating advertisements or informational content.

Another noteworthy characteristic of the Sharp PN-E802 is its robust build and reliability. Designed for 24/7 operation, this display can withstand constant use without compromising performance. It also features a sleek design, making it an aesthetic addition to any corporate or public space.

Finally, connectivity options abound with the PN-E802, including multiple HDMI, DisplayPort, and DVI inputs, allowing for a versatile array of connection types. This ensures compatibility with various devices, from computers to media players, making installation and integration into existing AV systems straightforward.

In summary, the Sharp PN-E802 and PNE802 models are high-performance displays that combine advanced technology, exceptional image quality, and versatile functionality, making them an excellent choice for any professional setting. Whether for presentations, signage, or collaborative work, these displays deliver an unparalleled viewing experience that stands out in any environment.