Sharp XG-P25X Replacing the Lamp, Removing and installing the lamp unit, Bottom filter cover

Page 65

Replacing the Lamp

CAUTION

•Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized LCD Projector Dealer or Service Center for a replacement.

•Do not remove the lamp cage directly after operation of the projector. The lamp may be extremely hot. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp cage to fully cool before removing the lamp cage.

It is recommended that the lamp be replaced after approximately 1,400 cumulative hours of use or when you notice a significant deterioration of the picture and color quality. Carefully change the lamp by following the steps below.

If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized LCD Projector Dealer or Service Center for repair. Purchase a replacement lamp unit (lamp/cage module) of the current type BQC-XGP25X//1 from your nearest Sharp Authorized LCD Projector Dealer or Service Center. Then carefully change the lamp by following the instructions below. If you wish, you may have the lamp replaced at your nearest Sharp Authorized LCD Projector Dealer or Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized LCD Projector Dealer or Service Center. For the name of the nearest Sharp Authorized LCD Projector Dealer or Service Center,

please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

U.S.A. ONLY

Caution Concerning the Lamp

•This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

•When the LAMP REPLACEMENT indicator and on-screen display icon is illuminated or flashes, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

•Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult with a doctor as soon as possible.

•Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized LCD Projector Dealer or Service Center to remove the damaged lamp and assure safe operation.

Removing and installing the lamp unit

CAUTION

•Be sure to remove the lamp cage by the handle. Be sure not to touch the glass surface of the lamp cage or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.

•Be sure to change the air filter during lamp replacement. The air filter comes packaged with the lamp unit.

Turn off the

Disconnect the

Remove the

Remove the

1 power.

2 power cord.

3 bottom filter cover.

4 air filter.

Press POWER OFF.

Unplug the power cord

Turn over the projector.

Grasp the air filter

Wait until the cooling

from the AC socket.

Press the tab and lift

between your fingers

fan stops.

 

open the filter cover in

and lift it out of the filter

 

 

the direction of the

cover.

 

 

arrow.

 

 

 

Tab

 

Troubleshooting

Maintenance&

 

 

E-62

XG-P25X/CD (E)-g

62

02.3.19, 7:12 PM

Page 64 Page 66
Image 65
Page 64 Page 66
Contents XG-P25X Model No. XG-P25X Serial No XG-P25X/CD/SUP English IntroductionProduct Disposal Accessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check Wall or Ceiling MountingPrecaución Précaution BQC-XGP25X//1 Using the Carrying Handle Temperature Monitor FunctionUsing the Kensington Lock Lamp Monitor FunctionComputer Compatibility Outstanding FeaturesTwo Optional Lenses for Maximum Flexibility Contents Multiple Function For Windows For Macintosh To Install Acrobat Reader from the CD-ROMFor other operating systems For other languages For WindowsSpeakers Foot releases Part NamesProjector Remote Control Available Range of the Remote Control Using the Remote ControlUsing as a Wired Remote Control Inserting the batteriesOptional Accessories AccessoriesSupplied Accessories Connections Power SupplyConnecting the Power Cord Connecting to a computer using the standard 15-pin Input Connecting the Projector to a ComputerProjecting Computer Images ComputerProjecting Computer Images Plug and Play function when connecting to a 15-pin terminalConnecting to a computer using the direct digital input port Connecting to a computer using the RS-232C PortLaser disc player Watching Video ImagesExample Watching Component Video Images Connecting to an amplifier and other audio componentsFor Better Sound AmplifierPress Power OFF Power ON/OFFPress Power on Using the Lens Shift Setting Up the ScreenUsing the Adjustment Feet Keystone setting Remote control Digital Image AdjustmentsSize setting Digital shift settingStandard Setup Front Projection Adjusting the Projection DistanceNormal Mode Stretch ModeUpper and Lower Lens Shift Position Ceiling Mount Adjusting the Projection DistanceUpper and Lower Lens Shift Position Standard Lens Throw distance ratio 11.8 to AN-P9MX AN-P48EZ Image Projection Projection Using a MirrorRear Projection Ceiling-mount ProjectionSelecting the Input Signal Source Using the Operation ButtonsAdjusting the Volume Muting the SoundDisplaying a Still Image Superimposing a Black ScreenPress Enlarge Pan Around the Screen Magnifying a Specific Portion of an ImageComputer Image Adjustments using Auto Sync Displaying and Setting the Break TimerComputer Adjusting the Picture Aspect RatioVideo Adjusting the Picture Aspect RatioPresentation Example RGB modeGamma Correction Function GUI On-screen Display Input 1, 2 RGB or 3 Digital mode Using the GUI Graphical User Interface Menu ScreenInput 4, 5 Video mode Basic OperationsMenu Bars Items on the Input 1, 2 or 3 Mode Menu BarMain menu Sub menuMenu Bars Items on the Input 4 or 5 Mode Menu BarAdjusting the Color Temperature Adjusting the PictureSelecting the Signal Type RGB menu only RGB input in Input 1 or 2 modeAdjusting the Picture Progressive ModeSelects the progressive conversion mode 2D Progressive Film ModeSaving and Selecting Adjustment Settings Adjusting the Computer Images RGB menu onlyPhase ClockAdjusting the Computer Images RGB menu only Special Mode AdjustmentChecking the Input Signal Auto Sync Display Function Auto Sync AdjustmentOff NormalAudio Out Adjusting the SoundSpeaker Selected item ButtonReducing Image Noise Video menu only Displaying Dual Pictures RGB menu onlyTurning On/Off the On-screen Display Setting the Video Signal Video menu onlySelected item Description Normal Level aSelecting a Background Image Selected item Description Sharp Sharp default image CustomSelecting a Startup Image None Black screenPower Save Function Selecting the Economy ModeAutomatic Power Shutoff Function Monitor Out/RS-232C Off FunctionReversing/Inverting Projected Images Confirming the Lamp Usage TimeLocking the Operation Buttons on the Projector Setting the Stacking ModeSelecting the Transmission Speed RS-232C Deselecting InputsControling Multiple Projectors with ID Numbers Setting the ID NoChanging the Password Protecting Important Settings with a PasswordSetting the Password Selecting the On-screen Display Language Displaying the Adjustment SettingsInput 1, 2 RGB or 3 Digital mode Internet Using Extended Functionality FeaturesMultiple and group projector control via computer Using Extended Functionality FeaturesStack Projection Videowall Maintenance Indicators Lamp/Maintenance IndicatorsCondition Problem Possible Solution LampPress Power OFF Removing and installing the lamp unitReplacing the Lamp Bottom filter coverCover.Remove the lamp cage Resetting the lamp timerInsert the new lamp cage cover.Attach the lamp cage Cleaning the side air filter not removable Cleaning and replacing the bottom air filterReplacing the Air Filter Cover.Replace the filterProblem Check TroubleshootingFor Sharp Assistance Input 3 DVI Port 29-pin Connecting Pin AssignmentsCommands RS-232C Specifications and Command SettingsPC control Communication conditionsRS-232C Specifications and Command Settings Model Name Specifications of wired remote control input Wired Remote Control Terminal SpecificationsSharp remote control signal format Function and transmission codesVGA Compatibility ChartUnits inches mm DimensionsPAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC SpecificationsAspect ratio GlossaryBorder IndexSharp Corporation
Top Page Image Contents