Sharp XG-P25X operation manual Precaución Précaution BQC-XGP25X//1

Page 8

IMPORTANT SAFEGUARDS

LAMP REPLACEMENT CAUTION

BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT SURFACE INSIDE ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-XGP25X//1 ONLY.

UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.

MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE.

SEE OPERATION MANUAL.

Caution Concerning the Lamp Replacement

See “Replacing the Lamp” on pages 62 and 63 .

PRODUCT DISPOSAL

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronics Industries Alliance: www.eiae.org .

Caution Concerning the Lamp Unit

Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized LCD Projector Dealer or Service Center for a replacement.

See “Replacing the Lamp” on pages 62 and 63 .

CAUTION

PRECAUCIÓN

PRÉCAUTION

BQC-XGP25X//1

E-5

XG-P25X/CD (E)-a

5

Cautions Concerning the Setup of the Projector

For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the lens must be cleaned more often. As long as the projector is properly maintained in this manner, use in these environments will not reduce the overall operation life. Please note that all internal cleaning must be performed by a Sharp Authorized LCD Projector Dealer or Service Center.

Notes on Operation

•The exhaust vent, the lamp cage cover and adjacent areas may be extremely hot during projector operation. To prevent injury, do not touch these areas until they have sufficiently cooled.

•Allow at least 12 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

•If the cooling fan becomes obstructed, a protection device will automatically turn off the projector lamp. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes. Then turn on the power by plugging the power cord back in. This will return the projector to the normal operating condition.

02.3.19, 7:15 PM

Page 7 Page 9
Image 8
Page 7 Page 9
Contents XG-P25X Model No. XG-P25X Serial No XG-P25X/CD/SUP Introduction EnglishProduct Disposal Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check Wall or Ceiling MountingPrecaución Précaution BQC-XGP25X//1 Temperature Monitor Function Using the Carrying HandleUsing the Kensington Lock Lamp Monitor FunctionOutstanding Features Computer CompatibilityTwo Optional Lenses for Maximum Flexibility Contents Multiple Function To Install Acrobat Reader from the CD-ROM For Windows For MacintoshFor other operating systems For other languages For WindowsSpeakers Foot releases Part NamesProjector Remote Control Using the Remote Control Available Range of the Remote ControlUsing as a Wired Remote Control Inserting the batteriesOptional Accessories AccessoriesSupplied Accessories Connections Power SupplyConnecting the Power Cord Connecting the Projector to a Computer Connecting to a computer using the standard 15-pin InputProjecting Computer Images ComputerPlug and Play function when connecting to a 15-pin terminal Projecting Computer ImagesConnecting to a computer using the RS-232C Port Connecting to a computer using the direct digital input portLaser disc player Watching Video ImagesExample Connecting to an amplifier and other audio components Watching Component Video ImagesFor Better Sound AmplifierPress Power OFF Power ON/OFFPress Power on Using the Lens Shift Setting Up the ScreenUsing the Adjustment Feet Remote control Digital Image Adjustments Keystone settingSize setting Digital shift settingAdjusting the Projection Distance Standard Setup Front ProjectionNormal Mode Stretch ModeUpper and Lower Lens Shift Position Ceiling Mount Adjusting the Projection DistanceUpper and Lower Lens Shift Position Standard Lens Throw distance ratio 11.8 to AN-P9MX AN-P48EZ Projection Using a Mirror Image ProjectionRear Projection Ceiling-mount ProjectionUsing the Operation Buttons Selecting the Input Signal SourceAdjusting the Volume Muting the SoundSuperimposing a Black Screen Displaying a Still ImageMagnifying a Specific Portion of an Image Press Enlarge Pan Around the ScreenDisplaying and Setting the Break Timer Computer Image Adjustments using Auto SyncAdjusting the Picture Aspect Ratio ComputerAdjusting the Picture Aspect Ratio VideoPresentation Example RGB modeGamma Correction Function Using the GUI Graphical User Interface Menu Screen GUI On-screen Display Input 1, 2 RGB or 3 Digital modeInput 4, 5 Video mode Basic OperationsItems on the Input 1, 2 or 3 Mode Menu Bar Menu BarsMain menu Sub menuItems on the Input 4 or 5 Mode Menu Bar Menu BarsAdjusting the Picture Adjusting the Color TemperatureSelecting the Signal Type RGB menu only RGB input in Input 1 or 2 modeProgressive Mode Adjusting the PictureSelects the progressive conversion mode 2D Progressive Film ModeAdjusting the Computer Images RGB menu only Saving and Selecting Adjustment SettingsPhase ClockAdjusting the Computer Images RGB menu only Special Mode AdjustmentChecking the Input Signal Auto Sync Adjustment Auto Sync Display FunctionOff NormalAdjusting the Sound Audio OutSpeaker Selected item ButtonDisplaying Dual Pictures RGB menu only Reducing Image Noise Video menu onlySetting the Video Signal Video menu only Turning On/Off the On-screen DisplaySelected item Description Normal Level aSelected item Description Sharp Sharp default image Custom Selecting a Background ImageSelecting a Startup Image None Black screenSelecting the Economy Mode Power Save FunctionAutomatic Power Shutoff Function Monitor Out/RS-232C Off FunctionConfirming the Lamp Usage Time Reversing/Inverting Projected ImagesSetting the Stacking Mode Locking the Operation Buttons on the ProjectorDeselecting Inputs Selecting the Transmission Speed RS-232CSetting the ID No Controling Multiple Projectors with ID NumbersChanging the Password Protecting Important Settings with a PasswordSetting the Password Selecting the On-screen Display Language Displaying the Adjustment SettingsInput 1, 2 RGB or 3 Digital mode Using Extended Functionality Features InternetUsing Extended Functionality Features Multiple and group projector control via computerStack Projection Videowall Lamp/Maintenance Indicators Maintenance IndicatorsCondition Problem Possible Solution LampRemoving and installing the lamp unit Press Power OFFReplacing the Lamp Bottom filter coverCover.Remove the lamp cage Resetting the lamp timerInsert the new lamp cage cover.Attach the lamp cage Cleaning and replacing the bottom air filter Cleaning the side air filter not removableReplacing the Air Filter Cover.Replace the filterTroubleshooting Problem CheckFor Sharp Assistance Connecting Pin Assignments Input 3 DVI Port 29-pinRS-232C Specifications and Command Settings CommandsPC control Communication conditionsRS-232C Specifications and Command Settings Model Name Wired Remote Control Terminal Specifications Specifications of wired remote control inputSharp remote control signal format Function and transmission codesCompatibility Chart VGADimensions Units inches mmSpecifications PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSCGlossary Aspect ratioIndex BorderSharp Corporation
Top Page Image Contents