Sharp XG-P20XU operation manual Power ON/OFF, On-screen Display, Flashing green Warming up

Page 20

Setup Connections&

Power ON/OFF

	Press POWER ON on the projector or
	POWER on the GyroRemote.
	• The flashing green LAMP REPLACEMENT indicator
	shows that the lamp is warming up. Wait until the
	indicator stops flashing before operating the projector.
POWER	• If the power is turned off and then immediately turned
	on again, it may take a short while before the lamp
	turns on.
	• When the projector cannot recognize GyroRemote, an on-
	screen display appears. Follow the instructions to activate
	control.
	• After the projector is unpacked and turned on for the first
	time, a slight odor may be emitted from the exhaust vent.
	This odor will soon disappear with use.

LAMP REPLACEMENT indicator

On-screen Display

When the power is on, the LAMP REPLACEMENT indicator lights, indicating the status of the lamp. Green: Lamp is ready.

Flashing green: Warming up.

Red: Change the lamp.

Press POWER OFF on the projector or POWER on the GyroRemote.

Press POWER OFF/POWER again while the message is displayed.

•If you accidentally pressed POWER OFF/POWER and do not want to turn off the power, wait until the power off screen disappears.

•When the power is turned off, the POWER indicator will light up red and the cooling fan will run for about 90 seconds. The projector will then enter standby mode.

•Wait until the cooling fan stops before disconnecting the power cord.

•The power can be turned on again by pressing POWER ON/POWER. When the power is turned on, the POWER indicator and the LAMP REPLACEMENT indicator light green.

•The POWER indicator flashes if the bottom filter cover is not securely installed.

E-19

Image 20

Contents XG-P20XU Introduction EnglishImportant Safeguards Important Safeguards ProjectorUsing the Kensington Lock Temperature Monitor FunctionUsing the Carrying Handle Outstanding Features Computer CompatibilityNetwork Capability Contents Multiple Function For other operating systems For other languages To Install Acrobat Reader from the CD-ROMFor Windows For Macintosh Part Names Front ViewGyroRemote Inserting and removing the batteriesOptional cables AccessoriesSupplied Accessories Connections Power SupplyConnecting the Power Cord Projecting Computer Images Connecting the Projector to a ComputerConnecting to a computer using the standard 15-pin Input Plug and Play function when connecting to a 15-pin terminal Projecting Computer ImagesConnecting to a computer using the RS-232C Port Connecting to a computer using the direct digital input portLaser disc player Watching Video ImagesExample Connecting to an amplifier and other audio components Watching Component Video ImagesFor Better Sound AmplifierFlashing green Warming up Power ON/OFFOn-screen Display Using the Lens Shift Setting Up the ScreenUsing the Adjustment Feet Digital Image Adjustments Keystone settingSize setting Digital shift settingThrow Distance Adjusting the Projection DistanceStandard Setup Front Projection Upper and Lower Lens Shift Position Ceiling Mount Adjusting the Projection DistanceUpper and Lower Lens Shift Position Standard Lens Throw distance ratio 11.8 to AN-W6EZ AN-T6EZ AN-P9MX AN-P48EZ Projection Using a Mirror Image ProjectionRear Projection Ceiling-mount ProjectionGyroRemote Features Introducing GyroRemoteRF Technology Multi-Projector ControlGyroRemote Features Gesture trackingProjector Control Mouse ControlUsing GyroRemote Menu AdjustmentsPreparation Operating the screen pointerAll Button Assign selections Using GyroRemoteFunction Assign Using the Presentation Tools Displaying the Break TimerOperating the mouse Connecting the projector to the computerUsing the mouse Setting up GyroRemote Setting RF channelsSwitching RF channels Confirming the present RF channelOperating multiple projectors with one GyroRemote Setting up GyroRemoteUsing multiple GyroRemotes to operate one projector Using as a Wired Remote Control Using the GyroRemote with a wired remote control cableUsing the IR remote control as a wired remote Turning off GyroRemoteUsing the Operation Buttons Selecting the Input Signal SourceAdjusting the Volume Muting the SoundSuperimposing a Black Screen Displaying a Still ImageMagnifying a Specific Portion of an Image Pan Around the ScreenAdjusting the Picture Aspect Ratio ComputerOn-screen Display Example RGB mode Gamma Correction FunctionUsing the GUI Graphical User Interface Menu Screen Basic OperationsItems on the Input 1, 2 or 3 Mode Menu Bar Menu BarsMain menu Sub menuItems on the Input 4 or 5 Mode Menu Bar Menu BarsAdjusting the Picture Adjusting the Color TemperatureSelecting the Signal Type RGB menu only RGB input in Input 1 or 2 modeProgressive Mode Adjusting the PictureSelects the progressive conversion mode 2D Progressive Film ModeAdjusting the Computer Images RGB menu only Saving and Selecting Adjustment SettingsPhase ClockAdjusting the Computer Images RGB menu only Special Mode AdjustmentChecking the Input Signal Auto Sync Adjustment Auto Sync Display FunctionOff NormalAdjusting the Sound Audio OutSpeaker Selected item ButtonDisplaying Dual Pictures RGB menu only Reducing Image Noise Video menu onlySetting the Video Signal Video menu only Turning On/Off the On-screen DisplaySelecting a Background Image Selecting a Startup ImageMonitor Out/RS-232C Off Function Selecting the Economy ModeAutomatic Power Shutoff Function Confirming the Lamp Usage Time Reversing/Inverting Projected ImagesSetting the Stacking Mode Locking the Operation Buttons on the ProjectorDeselecting Inputs Selecting the Transmission Speed RS-232CSetting the ID No Controling Multiple Projectors with ID NumbersChanging the Password Protecting Important Settings with a PasswordSetting the Password Displaying the Adjustment Settings Selecting the On-screen Display LanguageUsing Extended Functionality Features InternetUsing Extended Functionality Features Multiple and group projector control via computerStack Projection Videowall Lamp Lamp/Maintenance IndicatorsMaintenance Indicators Removing and installing the lamp unit Replacing the LampResetting the lamp timer Replacing the LampReplacing the Air Filter Cleaning and replacing the bottom air filterCleaning the side air filter not removable Troubleshooting For Sharp Assistance U.S.A. onlyConnecting Pin Assignments Input 3 DVI Port 29-pinRS-232C Specifications and Command Settings CommandsPC control Communication conditionsRS-232C Specifications and Command Settings Model Name Internal GND Transmission control codeComputer Compatibility Chart VGADimensions Units inches mmSpecifications PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSCGlossary Aspect ratioIndex Sharp Corporation