Sharp XG-P20XU Setting up GyroRemote, Operating multiple projectors with one GyroRemote

Page 38

Setting up GyroRemote

TEACH/LEARN

•Each GyroRemote has its own ID code, which must be recognized by the projector that is going to be used.

•The projector only recognizes the signal of the GyroRemote whose ID code has been input. Signals from other projectors or GyroRemotes that may be operating in the same area are not allowed to interrupt each other.

ButtonsOperation

ProjectorGyroRemote

ENTER

TEACH

LEARN

1 Press LEARN on the projector.

2 While “Do you want to LEARN?” is displaying, press ENTER. You are now in LEARN mode.

CAUTION

•Entering LEARN mode erases all previously registered GyroRemotes data. You must re-enter each GyroRemote ID code in order for the projector to recognize them again.

3 Press TEACH located on the front, inside the upper cover on the remote within 5 minutes. “Register” will appear on the display and you can now start using the GyroRemote with the projector.

4 To exit from the LEARN mode, press LEARN.

•LEARN mode will exit if the LEARN is pressed or 5 minutes has elapsed.

On-screen Display

Operating multiple projectors with one GyroRemote

CAUTION

•Be aware that you can operate multiple projectors with one GyroRemote, even if you are in another room, as long as you stay within a 98 5 (30 m) range of the projector.

1 Set projector to LEARN mode.

2 Press TEACH on the GyroRemote. You can now operate multiple projectors with one GyroRemote.

3 Perform steps 1 and 2 for each projector you plan to use.

4 To exit from LEARN mode, press LEARN.

•For setting multiple units in LEARN mode at one time, perform step 1 above for all projectors.

Using multiple GyroRemotes to operate one projector

One projector can recognize up to 8 GyroRemote ID codes.

1 Set projector to LEARN mode.

2 Press TEACH on all GyroRemotes being used. Once the eighth GyroRemote is registered to operate one projector, the LEARN mode automatically finishes. You can now operate one projector using multiple GyroRemotes.

3 To exit from the LEARN mode, press LEARN.

•Contact your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center if you need to use an additional GyroRemote unit.

E-37

Image 38

Contents XG-P20XU Introduction EnglishImportant Safeguards Important Safeguards ProjectorUsing the Kensington Lock Temperature Monitor FunctionUsing the Carrying Handle Outstanding Features Computer CompatibilityNetwork Capability Contents Multiple Function For other operating systems For other languages To Install Acrobat Reader from the CD-ROMFor Windows For Macintosh Part Names Front ViewGyroRemote Inserting and removing the batteriesOptional cables AccessoriesSupplied Accessories Connections Power SupplyConnecting the Power Cord Projecting Computer Images Connecting the Projector to a ComputerConnecting to a computer using the standard 15-pin Input Plug and Play function when connecting to a 15-pin terminal Projecting Computer ImagesConnecting to a computer using the RS-232C Port Connecting to a computer using the direct digital input portLaser disc player Watching Video ImagesExample For Better Sound Connecting to an amplifier and other audio componentsWatching Component Video Images AmplifierFlashing green Warming up Power ON/OFFOn-screen Display Using the Lens Shift Setting Up the ScreenUsing the Adjustment Feet Size setting Digital Image AdjustmentsKeystone setting Digital shift settingThrow Distance Adjusting the Projection DistanceStandard Setup Front Projection Upper and Lower Lens Shift Position Ceiling Mount Adjusting the Projection DistanceUpper and Lower Lens Shift Position Standard Lens Throw distance ratio 11.8 to AN-W6EZ AN-T6EZ AN-P9MX AN-P48EZ Rear Projection Projection Using a MirrorImage Projection Ceiling-mount ProjectionRF Technology GyroRemote FeaturesIntroducing GyroRemote Multi-Projector ControlProjector Control GyroRemote FeaturesGesture tracking Mouse ControlPreparation Using GyroRemoteMenu Adjustments Operating the screen pointerAll Button Assign selections Using GyroRemoteFunction Assign Using the Presentation Tools Displaying the Break TimerOperating the mouse Connecting the projector to the computerUsing the mouse Switching RF channels Setting up GyroRemoteSetting RF channels Confirming the present RF channelOperating multiple projectors with one GyroRemote Setting up GyroRemoteUsing multiple GyroRemotes to operate one projector Using the IR remote control as a wired remote Using as a Wired Remote ControlUsing the GyroRemote with a wired remote control cable Turning off GyroRemoteAdjusting the Volume Using the Operation ButtonsSelecting the Input Signal Source Muting the SoundSuperimposing a Black Screen Displaying a Still ImageMagnifying a Specific Portion of an Image Pan Around the ScreenAdjusting the Picture Aspect Ratio ComputerOn-screen Display Example RGB mode Gamma Correction FunctionUsing the GUI Graphical User Interface Menu Screen Basic OperationsMain menu Items on the Input 1, 2 or 3 Mode Menu BarMenu Bars Sub menuItems on the Input 4 or 5 Mode Menu Bar Menu BarsSelecting the Signal Type RGB menu only Adjusting the PictureAdjusting the Color Temperature RGB input in Input 1 or 2 modeSelects the progressive conversion mode 2D Progressive Progressive ModeAdjusting the Picture Film ModePhase Adjusting the Computer Images RGB menu onlySaving and Selecting Adjustment Settings ClockAdjusting the Computer Images RGB menu only Special Mode AdjustmentChecking the Input Signal Off Auto Sync AdjustmentAuto Sync Display Function NormalSpeaker Adjusting the SoundAudio Out Selected item ButtonDisplaying Dual Pictures RGB menu only Reducing Image Noise Video menu onlySetting the Video Signal Video menu only Turning On/Off the On-screen DisplaySelecting a Background Image Selecting a Startup ImageMonitor Out/RS-232C Off Function Selecting the Economy ModeAutomatic Power Shutoff Function Confirming the Lamp Usage Time Reversing/Inverting Projected ImagesSetting the Stacking Mode Locking the Operation Buttons on the ProjectorDeselecting Inputs Selecting the Transmission Speed RS-232CSetting the ID No Controling Multiple Projectors with ID NumbersChanging the Password Protecting Important Settings with a PasswordSetting the Password Displaying the Adjustment Settings Selecting the On-screen Display LanguageUsing Extended Functionality Features InternetUsing Extended Functionality Features Multiple and group projector control via computerStack Projection Videowall Lamp Lamp/Maintenance IndicatorsMaintenance Indicators Removing and installing the lamp unit Replacing the LampResetting the lamp timer Replacing the LampReplacing the Air Filter Cleaning and replacing the bottom air filterCleaning the side air filter not removable Troubleshooting For Sharp Assistance U.S.A. onlyConnecting Pin Assignments Input 3 DVI Port 29-pinPC control RS-232C Specifications and Command SettingsCommands Communication conditionsRS-232C Specifications and Command Settings Model Name Internal GND Transmission control codeComputer Compatibility Chart VGADimensions Units inches mmSpecifications PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSCGlossary Aspect ratioIndex Sharp Corporation