Vidikron VL-52, VL-57 manual Setup, Auto Adjust may take some time to complete, depending on

Page 48

Operation

Setup

Setup

OSD Language

PC Mode Adjust

Caption

Parental Control (VL-52 only)

Letterbox Mode

Input Selection

Monitor Out

Overscan

Input Label

HDMI Audio

RGB Signal

Film Mode

Auto Backlight

OSD Timer

Auto Off

Use the controls in the Setup menu to perform advanced image quality adjustments and access various other DView features.

OSD Language: Select OSD Language from the Setup menu and press ENTER. Then, use the up- or down-arrow buttons to select the OSD language (English, French, Spanish, Portuguese or German). Press ENTER again to confirm your selection.

PC Mode Adjust: To improve the quality of displayed images from a computer or other VESA-compliant, RGB (480p or higher) source, select PC Mode Adjust and press ENTER.

Auto Adjust: Auto Adjust automatically adjusts settings to optimize computer images. To execute Auto Adjust on command, select Auto Adjust and press ENTER.

Auto Adjust may take some time to complete, depending on the

Note

characteristics of the incoming signal.

 

Clock: Use the up- or down-arrow buttons ( , ) to highlight Clock. Then, use the right-arrow button ( ) to increase the pixel clock rate; use the left-arrow button ( ) to decrease it.

Phase: Adjust the phase if the image shows shimmer or “horizontal noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect of this control is similar to that of a tracking control on a VCR.

For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may notice that you can stabilize the image at more than one point. Use either setting in this case.)

H Position: Use the up- or down-arrow buttons ( , ) to highlight H Position. Then, use the right-arrow button ( ) to shift the image to the right; use the left-arrow button ( ) to shift the image to the left.

V Position: Use the up- or down-arrow buttons ( , ) to highlight V Position. Then, use the right-arrow button ( ) to shift the image up; use the left-arrow button ( ) to shift the image down.

To restore the factory-default Clock, Phase and Position settings, select Factory Reset and press ENTER.

Caption: Select Caption from the Setup menu to control the display of closed captions when watching programs that contain them.

Display: Select On or Off to control the display of closed captions.

Digital (VL-52 only): For digital TV broadcasts, select one of six captioning modes (Service1, Service2 ... Service6). Service1 usually contains the native-language captions; if a program is captioned in more than one language, those captions are carried on Service2 through Service6.

Analog: Select one of four captioning modes: CC1, CC2, CC3 or CC4. CC1 usually contains the native-language captions; if a program is captioned in more than one language, those captions are carried on CC2, CC3 or CC4.

The DView also supports “text mode” captioning; to use this feature, select Text1, Text2, Text3 or Text4. The text modes, instead of displaying a few lines of captions somewhere on the picture, take over all or half of the screen to display scrolling text information. (The text modes are seldom used today, so most of the time there is no information there to see.) The text field is sometimes used for embedding Internet data (called Interactive TV Links, or ITV Links) in the captions.

36

Vidikron VL-52 and VL-57 Owner’s Operating Manual

Image 48
Contents VL-52 and VL-57 Page ONE Year Limited Warranty For LCD DisplaysRIGHTS, Limits and Exclusions Vidikron Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial Communications1List of Figures List of Figures Xii 1Introduction About This ManualUsing This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Volume Adjustment Buttons VOL / VOL +2Controls and Functions DView at a GlancePower Button Remote Control Sensor Status Indicator LED CH / CHHeadphone Jack Main Power Switch INPUT3 Component Video RCA connectorsINPUT4 Component Video RCA connectors INPUT2 S-Video InputAIR Antenna Input VL-52 only Cable Input VL-52 onlyDView Remote Control DView Remote ControlMemory Preset Buttons OFF / onNumeric Buttons Source Selection ButtonsAspect Ratio Selection Buttons ANA 169 Anamorphic 4X3 StandardLetbox Letterbox Wide IntelliWideTimer OFF Button Sound Control ButtonsSurrnd Surround Channel Selection Short-Cuts VL-52 only3Installation Remote ControlTo install batteries in the remote control Quick Setup Installation OverviewStep Procedure For Details, refer to Installation Considerations Wall-Mounting the DViewAmbient Light Connections to the DView Antenna/Cable TV ConnectionHdmi Connections Rear of the Display Rear of the PC DVD/DTV STB AV OUT Connections Connecting External Speakers OptionalAmplifier Connector Pin Assignments ConnectionRear Panel Turning on the Power 4OperationChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Picture Adjust Timer VL-52Setup SourceMain Menu SourceAspect Ratio Aspect Ratio Settings Control DescriptionPerform the adjustments in the order listed here Picture AdjustTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Channel VL-52 only Timer VL-52 only Setup Auto Adjust may take some time to complete, depending onFCC Ratings and Content Categories Rating/Category DescriptionLetterbox Mode = Letterbox Operation ISF Calibration Should be used by ISF-certified technicians only100 DView Splash Screen Aspect Size Position PIPUsing Picture-In-Picture PIP Available Main and PIP Source Combinations VideoChanging the PIP Position Changing the PIP SizeChanging the PIP Aspect Ratio Audio Programs Swap button on the remote control ImagesBroadcast Mode Receive Mode Mono Stereo Stereo Sound/SAP VL-52 onlyCompatibility with Stereo and SAP Audio Broadcasts Mono+SAPOperation 5Maintenance and Troubleshooting CleaningTroubleshooting Tips Troubleshooting ChartComputer Signal Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial CommunicationsCommand Description S4ESDB 0027 0024 Serial Communications 7Specifications DView SpecificationsWeight including stand Regulatory Approvals Limited Warranty Specifications are subject to change without noticeDView Dimensions VL-52 DimensionsVL-57 Dimensions Computer/Video Signal Compatibility Chart Computer Signal CompatibilitySignal Mode Vertical Frequency Horizontal Specifications Page Vidikron

VL-57, VL-52 specifications

The Vidikron VL-52 and VL-57 are high-performance projection television models that encapsulate advanced technology and design, aimed at delivering an exceptional viewing experience. Manufactured during an era when home theater systems were evolving, these models became known for their cutting-edge features and superior picture quality, setting a benchmark in the projection television market.

The VL-52 features a 52-inch screen size, while the VL-57 sports a larger 57-inch display, both offering expansive viewing areas ideal for home cinema setups. One of the key characteristics of these models is their use of a high-resolution CRT (Cathode Ray Tube) technology, which provides vibrant colors and deep blacks, enhancing the overall image quality. The zoned convergence adjustment allows users to fine-tune the picture, ensuring that colors align perfectly across the entire screen.

In terms of features, both models support various video formats, including 480i, 480p, and 1080i, allowing for high-definition viewing on compatible content. The inclusion of multiple inputs, such as component, composite, and S-Video, ensures that users can connect a variety of devices, from DVD players to gaming consoles, easily. This versatility makes the VL-52 and VL-57 attractive options for consumers seeking a comprehensive entertainment solution.

The technologies integrated into these models also contribute to their performance. The onboard video processing capabilities enhance image clarity and reduce motion blur, making fast-paced action scenes more enjoyable. Furthermore, both models are equipped with an advanced color management system, which ensures that colors remain true to the source material, providing viewers with a lifelike experience that is reminiscent of the cinema.

Another noteworthy characteristic is the build quality. The Vidikron VL-52 and VL-57 feature a robust and elegant design, making them a fitting centerpiece in any home theater setup. The attractive cabinet work and premium materials used in their construction reflect the brand's commitment to quality and aesthetics.

Overall, the Vidikron VL-52 and VL-57 remain iconic models, blending technology, performance, and design. As home entertainment continues to evolve, these projectors stand as a testament to the innovation that defined their era, offering features and characteristics that can still impress enthusiasts today.