Vidikron VL-57, VL-52 manual Sdb

Page 65

Serial Communications

Table 6-1. Serial Commands

	Command					Description

[		SDB		000#	Set PIP size
					0	= small
					1	= medium
					2	= large

Example: [SDB0001 selects medium PIP size

[		SDE		000#	Set PIP aspect ratio
					0	= 4:3
					1	= 16:9

Example: [SDE0001 selects 16:9 aspect ratio PIP window

[		SDF		000#	Set PIP window position
					0	= Top/Left
					1	= Top/Right
					2	= Bottom/Left
					3	= Bottom/Right

Example: [SDF0001 positions PIP window in upper-right corner of display area

The following serial commands are meant to emulate buttons on the remote control. Each button has its own serial command, so effectively it is as if you were using the IR remote only you’ll be doing so via serial commands. These commands provide active OSD responses just like the IR remote.

Each command begins with [key followed by the four-digit number of the button. No carriage return is necessary. The response you receive from the unit if the command is valid will be a right-bracket (]) followed by the four-digit numeric code you sent. (For example, the ‘ON’ command is [key0015; the response will be ]0015). All commands are in ASCII.

[

[

[

key	0002	OFF
	0015	ON
key	0004	Number 1
	0005	Number 2
	0006	Number 3
	0008	Number 4
	0009	Number 5
	0010	Number 6
	0012	Number 7
	0013	Number 8
	0014	Number 9
	0035	Number “–”
	0017	Number 0
	0023	TV
key	0105	INPUT1

Vidikron VL-52 and VL-57 Owner’s Operating Manual

53

Image 65

Contents

VL-52 and VL-57 Page For LCD Displays ONE Year Limited WarrantyRIGHTS, Limits and Exclusions Vidikron Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part 1Table of Contents Specifications Maintenance and TroubleshootingOperation Serial Communications1List of Figures List of Figures Xii About This Manual 1IntroductionThey also provide supplemental information Using This ManualPerformance or cause a malfunction If you need Turn toKey Features and Benefits Description, Features and BenefitsOptional Accessories Volume Adjustment Buttons VOL / VOL + Controls and Indicators2Controls and Functions DView at a GlanceCH / CH Power Button Remote Control Sensor Status Indicator LEDINPUT3 Component Video RCA connectors Headphone Jack Main Power SwitchINPUT4 Component Video RCA connectors INPUT2 S-Video InputCable Input VL-52 only AIR Antenna Input VL-52 onlyDView Remote Control DView Remote ControlOFF / on Memory Preset ButtonsNumeric Buttons Source Selection Buttons4X3 Standard Aspect Ratio Selection Buttons ANA 169 AnamorphicLetbox Letterbox Wide IntelliWideSound Control Buttons Timer OFF ButtonSurrnd Surround Channel Selection Short-Cuts VL-52 onlyTo install batteries in the remote control 3InstallationRemote Control Step Procedure For Details, refer to Quick SetupInstallation Overview Ambient Light Installation ConsiderationsWall-Mounting the DView Antenna/Cable TV Connection Connections to the DViewHdmi Connections Rear of the Display Rear of the PC DVD/DTV STB AV OUT Connections Amplifier Connecting ExternalSpeakers Optional Rear Panel Connector Pin AssignmentsConnection Changing the OSD Language Turning on the Power4Operation Setting the PC Display Properties Using the On-Screen Menus Timer VL-52 Picture AdjustSetup SourceAspect Ratio Main MenuSource Control Description Aspect Ratio SettingsPicture Adjust Perform the adjustments in the order listed hereTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Channel VL-52 only Timer VL-52 only Auto Adjust may take some time to complete, depending on SetupRating/Category Description FCC Ratings and Content CategoriesLetterbox Mode = Letterbox Operation Should be used by ISF-certified technicians only ISF Calibration100 DView Splash Screen Aspect Size Position PIPUsing Picture-In-Picture PIP Video Available Main and PIP Source CombinationsChanging the PIP Aspect Ratio Changing the PIP PositionChanging the PIP Size Images Audio Programs Swap button on the remote controlStereo Sound/SAP VL-52 only Broadcast Mode Receive Mode Mono StereoCompatibility with Stereo and SAP Audio Broadcasts Mono+SAPOperation Cleaning 5Maintenance and Troubleshooting Troubleshooting Tips Troubleshooting ChartComputer Signal RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands 6Serial CommunicationsS4E Command DescriptionSDB 0027 0024 Serial Communications DView Specifications 7SpecificationsSpecifications are subject to change without notice Weight including stand Regulatory Approvals Limited WarrantyVL-52 Dimensions DView DimensionsVL-57 Dimensions Signal Mode Vertical Frequency Horizontal Computer/Video Signal Compatibility ChartComputer Signal Compatibility Specifications Page Vidikron