Sharp quick start Sharp PROJECTOR, Model XR-32X-L/XR-32S-L, Sharp Electronics Corporation, Only

Page 6
U.S.A. ONLY
U.S.A. ONLY

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Declaration of conformity

SHARP PROJECTOR, MODEL XR-32X-L/XR-32S-L

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party:

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07495-1163 TEL: 1-800-BE-SHARP (1-800-237-4277)

U.S.A. ONLY

PRODUCT DISPOSAL

This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP.

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 52.

This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 (XR- 32X)/480,000 (XR-32S) pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.

This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

Authorized representative responsible for the European Union Community Market

SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg

E.U. ONLY

2

Image 6
Contents XR-32X-L XR-32S-L XR-32X-LModel No Serial No This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianPage IntroductionENGLISH A. onlySharp PROJECTOR, Model XR-32X-L/XR-32S-L Sharp Electronics CorporationOnly Maintenance Troubleshooting Index For Future ReferenceContents Reference Power Sources CleaningAccessories Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally See Regarding the Lamp onUsing the projector in other countries Temperature monitor functionOther connected equipment Accessories Optional accessoriesPart Names and Functions ProjectorComputer Rear ViewAudio 1 input terminal Audio OUTCLICK/EFFECT COMPUTER, *DVIUP/PAGE CLICK/RETURNInserting the Batteries Usable Range Setup and Projection Quick StartHeight Upper side ControlStandard Setup Front Projection Setting up the ProjectorSetting up the Projector Ceiling-mount SetupProjection PRJ Mode Example Normal Mode Picture Size120 Normal Mode Stretch ModeScreen Size and Projection Distance Example Terminals of XR-32X Connecting the Projector to Other EquipmentYou may need other cables or connectors not listed below Is only for XR-32XConnecting the Projector to Other Equipment Audio XR-32S Connecting the Power Cord AC socket To AC outlet Power cord suppliedControlling the Projector by a Computer Turning the Projector on Lamp indicator Power indicator STANDBY/ON buttonTurning the Projector On/Off On-screen display confirmation messageAdjusting the Picture Size About the Setup GuideAdjusting the Projected Image Adjusting the Focus Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelPress Keystone to enter the Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Switching the Input Mode Adjusting the VolumeOn-screen display Resize Mode Press ResizeResize About Copyrights Using the Spot Function Operating with the Remote ControlDisplaying and Setting the Break Timer Switching the Eco+Quiet ModeFreezing a Moving Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Displaying an Enlarged Portion of an ImageWhen left-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When right-clickingMenu Items Following shows the items that can be set in the projectorScreen adjustment SCR-ADJ menu Items you can set with the Help menu Help menu nPress Q or O and select Picture to adjust Using the Menu ScreenMenu Selections Adjustments Example Adjusting BrightPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press EnterPAGE1 Picture Adjustment Picture MenuSelecting the Picture Mode Menu operation n4Adjusting the Colors 2Adjusting the Image3Adjusting the Color Temperature Adjusting Hue, Saturation, or Value7Lamp Setting ProgressiveReducing Image Noise DNR Adjusting the Image Position Keystone Correction Adjusting the Projected Image SCR ADJ MenuSetting the Resize Mode Setting the On-screen DisplayReversing/Inverting Projected Images Selecting the Setup GuideSelecting the Background Image Selecting the On-screen Display LanguageStandby Mode Auto Sync Auto Sync AdjustmentAuto Power Off Function Setting the Confirmation Sound System SoundSystem Lock Function Fan Mode SettingAudio Input XR-32X only Select System Lock, then press Enter or QEnter the same keycode in Re- confirm Keylock FunctionChecking the Lamp Life Status Locking the Operation ButtonsTroubleshooting with the Help Menu Enter button Adjustment buttons P/R/O/Q MENU/HELP buttonUtilizing the Help Menu Functions Maintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments Sub 15 pin female connectorDVI-D Terminal 24 pin connector XR-32X only RS-232C Terminal mini DIN 9 pin female connector USB Terminal Type B USB connectorCommunication conditions RS-232C Specifications and CommandsComputer control Basic formatRS-232C Specifications and Commands CommandsERR DNR Video Input Picture Mode Standard OK or ERR PAL Computer Compatibility Chart ComputerTroubleshooting 21-2449, 50 For Sharp Assistance Specifications Dimensions Index
Related manuals
Manual 73 pages 53.66 Kb