Sharp XR-32X-L, XR-32S-L quick start 49, 50

Page 68

Troubleshooting (Continued)

Problem

 

Check

Page

An unusual sound is

• If the picture is normal, the sound is due to cabinet shrinkage caused

occasionally heard from

 

by room temperature changes. This will not affect operation or

 

the cabinet.

 

performance.

 

Maintenance indicator on

• See “Maintenance Indicators”.

50

the projector illuminates

 

 

 

or blinks in red.

 

 

 

The projector cannot

• The keylock is set.

47

be turned on or put into

 

If the keylock is set to “ON”, all the buttons are locked.

 

the standby mode

 

 

 

using STANDBY/ON on

 

 

 

the projector.

 

 

 

Picture is green on

Change the input signal type setting.

48

COMPUTER

• When you cannot select an input signal type, select “Color is faded

40, 48

(Component)/

 

or poor” in the “Help” menu, after selecting an item other than

 

*DVI (Component).

 

“sRGB” in “Picture Mode”, and then select an input signal type.

 

Picture is pink

 

 

 

(no green) on

 

 

 

COMPUTER (RGB)/

 

 

 

*DVI (RGB).

 

 

 

Picture is too bright and

Image adjustments are incorrectly set.

41

whitish.

 

 

 

The cooling fan becomes

• When temperature inside the projector increases, the cooling fan

8, 9

noisy.

 

runs faster.

49, 50, 51

The lamp does not light

The lamp indicator is illuminating in red.

 

up even after the

 

Replace the lamp.

 

projector turns on.

 

 

50, 53

The lamp suddenly turns

 

 

 

off during projection.

 

 

 

The image sometimes

• Cables are incorrectly connected to the projector or the connected

21–24

flickers.

 

equipment works improperly.

 

 

Select “Vertical stripes or flickering image appear” in the “Help”

48

 

 

menu and make the necessary adjustments.

 

 

If this happens frequently, replace the lamp.

53

The lamp needs much

• The lamp will eventually need to be changed.

53

time to turn on.

 

While the remaining lamp life draws to a close, replace the lamp.

 

Picture is dark.

 

 

 

The remote control

Operate the remote control while pointing it at the projector’s remote

 

cannot be used.

 

control sensor.

 

 

• The remote control may be too far away from the projector.

 

 

If direct sunlight or a strong fluorescent lamp is shining on the

15

 

 

projector’s remote control sensor, place the projector where it will not

 

 

 

be affected by strong light.

 

 

• The batteries may be depleted or inserted incorrectly. Make sure the

14

 

 

batteries are inserted correctly or insert new ones.

 

 

 

 

 

* XR-32X only

 

 

 

This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.

64

Image 68
Contents XR-32X-L XR-32S-L XR-32X-LModel No Serial No This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianPage IntroductionENGLISH A. onlyOnly Sharp PROJECTOR, Model XR-32X-L/XR-32S-LSharp Electronics Corporation Maintenance Troubleshooting Index For Future ReferenceContents Reference Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents See Regarding the Lamp onOther connected equipment Using the projector in other countriesTemperature monitor function Accessories Optional accessoriesPart Names and Functions ProjectorRear View Audio 1 input terminalComputer Audio OUTCOMPUTER, *DVI UP/PAGECLICK/EFFECT CLICK/RETURNInserting the Batteries Usable Range Height Setup and ProjectionQuick Start Upper side ControlSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount Setup120 Projection PRJ ModeExample Normal Mode Picture Size Screen Size and Projection Distance Normal ModeStretch Mode Connecting the Projector to Other Equipment You may need other cables or connectors not listed belowExample Terminals of XR-32X Is only for XR-32XConnecting the Projector to Other Equipment Audio XR-32S Controlling the Projector by a Computer Connecting the Power CordAC socket To AC outlet Power cord supplied Lamp indicator Power indicator STANDBY/ON button Turning the Projector On/OffTurning the Projector on On-screen display confirmation messageAbout the Setup Guide Adjusting the Projected Image Adjusting the FocusAdjusting the Picture Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelCorrecting Trapezoidal Distortion Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction On-screen display Switching the Input ModeAdjusting the Volume Resize Resize ModePress Resize About Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageUsing the Remote Control as the Wireless Computer Mouse When moving the cursorWhen left-clicking When right-clickingMenu Items Following shows the items that can be set in the projectorScreen adjustment SCR-ADJ menu Items you can set with the Help menu Help menu nUsing the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Example Adjusting BrightTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press EnterPicture Adjustment Picture Menu Selecting the Picture ModePAGE1 Menu operation n2Adjusting the Image 3Adjusting the Color Temperature4Adjusting the Colors Adjusting Hue, Saturation, or ValueReducing Image Noise DNR 7Lamp SettingProgressive Adjusting the Projected Image SCR ADJ Menu Setting the Resize ModeAdjusting the Image Position Keystone Correction Setting the On-screen DisplaySelecting the Setup Guide Selecting the Background ImageReversing/Inverting Projected Images Selecting the On-screen Display LanguageAuto Sync Auto Sync Adjustment Auto Power Off FunctionStandby Mode Setting the Confirmation Sound System SoundFan Mode Setting Audio Input XR-32X onlySystem Lock Function Select System Lock, then press Enter or QKeylock Function Checking the Lamp Life StatusEnter the same keycode in Re- confirm Locking the Operation ButtonsUtilizing the Help Menu Functions Troubleshooting with the Help MenuEnter button Adjustment buttons P/R/O/Q MENU/HELP button Maintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer DVI-D Terminal 24 pin connector XR-32X only Connecting Pin AssignmentsSub 15 pin female connector RS-232C Terminal mini DIN 9 pin female connector USB Terminal Type B USB connectorRS-232C Specifications and Commands Computer controlCommunication conditions Basic formatRS-232C Specifications and Commands CommandsERR DNR Video Input Picture Mode Standard OK or ERR PAL Computer Compatibility Chart ComputerTroubleshooting 21-2449, 50 For Sharp Assistance Specifications Dimensions Index
Related manuals
Manual 73 pages 53.66 Kb