Runco CL-810 CINEWIDE Vertical and Horizontal, Position, Ceiling Installation, Floor Installation

Page 30

Installation

Vertical and Horizontal

Proper placement of the projector relative to the screen will yield a rectangular,

Position

 

perfectly-centered image that completely fills the screen.

 

 

Ideally, the projector should be positioned perpendicular to the screen and in such a way

 

 

that the lens center and screen center are aligned with each other, as shown in Figure 3-2.

Ceiling Installation

Ceiling

Height

Projection Distance

Lens Center

x

 

 

Screen

Lens Center

 

Floor Installation

 

 

 

Height

Screen

Lens Center

 

Lens Center

 

 

 

x

 

 

 

 

Projection Distance

 

 

 

Floor

 

Figure 3-2. Projector Placement

 

Vertical and Horizontal

If it is not possible to align the projector and screen as shown in Figure 3-2,you can use

Lens Shift

the lens shift (LENS) controls on the projector remote to center the image on the screen.

Lens shift is generally expressed as a percentage of the screen height or width, as shown in Figure 3-3and Figure 3-4.

Screen Center

0%

50% Height

Lens Shift

(0.5 x H)

Base plate

to lens center =

approx. 5-6" (depending

on the amount of lens shift)

100% Height

Lens Shift

(1.0 x H)

Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular

lens or projector is used in this example.

Figure 3-3. Vertical Lens Shift (EXAMPLE ONLY)

18

Runco CL-810 Series Owner’s Operating Manual

Image 30
Contents CL-810 Series Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents List of Figures List of Figures Xii Introduction About This ManualUsing This Manual Related DocumentsDescription, Features and Benefits Format screenOptional Accessories CL-810 and CL-810 Ultra Optional Accessories CL-810 Ultra OnlyControls and Functions CL-810 at a GlancePOWER/STANDBY LED Indicates power status as follows Cable Access Door Open to access connectorsCL-810 Rear Panel Connect only an SDC-1 to the R-Link input! AlthoughVolt 250 mA Trigger Output 3.5-mm, mini phono jack Comp 1 RCA connectorsPower Input 100 to 240 VAC Connect the CL-810 to power here Comp 2 / RGBCL-810 Remote Control CL-810 Remote ControlSource Selection Buttons RVR Reflectance Volume RegulationOn / OFF VID S-VideoContrast Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons COL ColorPicture-In-Picture PIP / Picture-By-Picture PBP Controls SDC-1 System Expansion DeviceMotorized Lens Controls Installation Remote ControlQuick Setup Installation specialistInstallation Considerations Installation TypeAmbient Light Estimating Throw Distance Lens Throw Range Throw Ratio Inches, with Lens Option96x54-inch Lens Only Anamorphic Minimum MaximumVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Lens Option CL-810 CL-810 Ultra ProteusFolded Optics Other ConsiderationsLens Motor Feet Install Lens MotorRemove Projector Front Mounting PlateAutoScope Lens Motor Installation Mounting the CL-810 CL-810 Connector Panel AccessConnections to System Expansion DeviceConnecting Source Components to the CL-810 10. HDMI/DVI Source Connections12. Progressive Component Video Connections DTV or Progressive Component YPbPr SourceDTV Source DVD Player, VCR Satellite Receiver Etc 13. Composite, S-Video and Component Video ConnectionsRS-232 Controller Connection16. Connecting the 12-Volt Trigger Output to Other Equipment AutoScope Lens Motor RearTurning on the Power Input voltage to the AutoScope lens motor must be betweenFocus Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments ZoomInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly18. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View GeometryFender Washer Adjusting the Lens Height Y Anamorphic Lens Set Screw Adjusting the Lens Height Y Geometry Installation Operation Selecting an Aspect Ratio Adjusting the PicturePicture Adjustment on Selecting Video MemoryUsing Picture-In-Picture/ Picture-By-Picture PIP/PBP Using the On-Screen MenusVideo InstallationSet Up Component1Picture Adjustment Main MenuEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set toYou must enter a passcode in order to enter the Set Up menu International Color Consortium ICC is a group of imagingAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view Takes effect immediately you do not need to press Enter To exitOption Shift controls in the Set Up menu see Set Up You select that menu after turning on the projectorOperation Remote Control Secondary Order to change the secondary IR codeIf your CL-810 Ultra installation includes an SDC-1 System ISF Calibration When you change a setting, save the change to a presetReset Picture Adjust This menu should be used by ISF-certified technicians onlyOperation Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionSymptom Maintenance and Troubleshooting Serial Communications Is turned on or offCode Function Serial Communications Serial Commands Serial Communications Specifications CL-810 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsCL-810 Specifications CL-810 Dimensions CL-810 DimensionsCL-810 Ultra Dimensions CL-810 Ultra DimensionsSpecifications Page RUMA-011135 Rev 04-23-07 Runco CL-810 Owner’s Operating Manual

CL-810 / SDC-1, CL-810 ULTRA, CL-810 CINEWIDE specifications

The Runco CL-810 series projectors, including the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE, represent a pinnacle of home theater projection technology, designed to deliver stunning visual experiences for cinephiles and home entertainment enthusiasts alike. Each model within the CL-810 lineup integrates advanced features and state-of-the-art technologies to create immersive viewing experiences.

At the heart of the Runco CL-810 projectors is the proprietary DHD Digital High Definition video processing technology, which enhances source content to achieve unparalleled clarity and detail. This technology ensures optimal image scaling and color reproduction, delivering true-to-life visuals that captivate audiences. The projectors also utilize a high-performance light engine, capable of producing intense brightness and a wide color gamut for vibrant images.

The CL-810 ULTRA model boasts a 1080p resolution, which is ideal for showcasing high-definition content. It features advanced lens options, including motorized zoom and lens shift capabilities, allowing for flexibility in installation and optimal image alignment. This model's extensive connectivity options include HDMI inputs, ensuring compatibility with a wide variety of media sources.

The CL-810 CINEWIDE stands out for its unique CinemaScope capabilities, enabling a native 2.35:1 aspect ratio. This feature allows users to enjoy a cinematic experience without the need for additional lens systems or image cropping. The CINEWIDE version also offers adjustable aspect ratio settings, providing versatility for various film formats.

In addition to their remarkable image quality, the Runco CL-810 projectors emphasize quiet operation and energy efficiency. With advanced cooling systems, these projectors minimize noise for a distraction-free viewing environment. Furthermore, their energy-efficient design reduces power consumption while still providing exceptional performance.

The CL-810 series supports extensive customization options, allowing users to tailor their projection experience according to their preferences. With advanced calibration capabilities, these projectors can be fine-tuned to match specific room environments, ensuring optimal performance regardless of viewing conditions.

In summary, the Runco CL-810 series, featuring the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE models, delivers a premium home theater experience characterized by stunning resolution, versatile aspect ratios, and impressive color reproduction. With cutting-edge technology and customizable features, these projectors are designed to satisfy even the most discerning home cinema enthusiasts.