Runco CL-810 / SDC-1 ISF Calibration, This menu should be used by ISF-certified technicians only

Page 74

Operation

 

ISF Calibration ➤

To access the ISF Calibration menu, select ISF Calibration from the Main Menu and press

 

 

 

ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu

 

ISF Calibration

 

passcode when prompted and press ENTER again. Then, press MENU on the remote

 

 

 

control.

 

Reset Picture Adjust

 

 

 

 

 

Picture Adjust

White Balance

This menu should be used by ISF-certified technicians only.

Gamma Selection

Note

 

Blue Image

 

ICC Adjust

Reset Picture Adjust: To restore the ISF default image settings for the current input

Store Settings

source ONLY, press the button to highlight “Yes” then press ENTER.

Splash Screen Timer

 

ISF Enable

Picture Adjust: These settings are described in the Picture Adjustment section

Return to User OSD

(page 48).

 

White Balance / Gamma Selection: These settings are described in the previous section, Set Up.

Blue Image: This setting is described in the Installation section (refer to page 56).

ICC Adjust: Use the ICC Adjust controls to customize the stored NTSC, HDTV and/or PAL color space characteristics. To do this, select the color space to modify. Then, select a component color (Red, Green, Blue, Yellow, Cyan or Magenta).

For each component color, you can adjust the following:

•Intensity: This slidebar adjusts the intensity -- also known as luminance -- of a given color.

•Sat. This slidebar adjusts the color saturation level -- the amount of that color in a video image. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

•Hue: This slidebar adjusts the red/green color hue for true color reproduction of video signals. For best results, adjust tint while displaying an external color bars test pattern (see Figure 4-4). Otherwise, it is recommended that Hue remain at its default setting.

When you have finished customizing the color space, select Store Setting and press

ENTER.

Store Settings: For each input, the CL-810 lets you store image quality settings as presets that you can recall at a later time. You can create up to three presets per input and resolution.

When you change a setting, save the change to a preset

Note afterwards. Otherwise, the change will be lost when a different input is selected. (Most settings are saved for each input and resolution separately.)

When you have finished calibration, select Store Settings and choose "Memory 1,” “ISF

Night” or “ISF Day” to store your settings.

To recall stored custom image quality settings, select Restore Image Settings from the Adjustment menu (refer to Picture Adjustment on page 48) and choose “Memory 1,” “ISF Night” or “ISF Day.” Or, simply use the corresponding buttons on the remote control.

62

Runco CL-810 Series Owner’s Operating Manual

Page 73 Page 75
Image 74
Page 73 Page 75
Contents CL-810 Series Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents List of Figures List of Figures Xii Introduction About This ManualUsing This Manual Related DocumentsDescription, Features and Benefits Format screenOptional Accessories CL-810 and CL-810 Ultra Optional Accessories CL-810 Ultra OnlyControls and Functions CL-810 at a GlancePOWER/STANDBY LED Indicates power status as follows Cable Access Door Open to access connectorsCL-810 Rear Panel Connect only an SDC-1 to the R-Link input! AlthoughVolt 250 mA Trigger Output 3.5-mm, mini phono jack Comp 1 RCA connectorsPower Input 100 to 240 VAC Connect the CL-810 to power here Comp 2 / RGBCL-810 Remote Control CL-810 Remote ControlSource Selection Buttons RVR Reflectance Volume RegulationOn / OFF VID S-VideoContrast Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons COL ColorMotorized Lens Controls Picture-In-Picture PIP / Picture-By-Picture PBP ControlsSDC-1 System Expansion Device Installation Remote ControlQuick Setup Installation specialistAmbient Light Installation ConsiderationsInstallation Type Estimating Throw Distance Lens Throw Range Throw Ratio Inches, with Lens Option96x54-inch Lens Only Anamorphic Minimum MaximumVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Lens Option CL-810 CL-810 Ultra ProteusFolded Optics Other ConsiderationsLens Motor Feet Install Lens MotorRemove Projector Front Mounting PlateAutoScope Lens Motor Installation Mounting the CL-810 CL-810 Connector Panel AccessConnections to System Expansion DeviceConnecting Source Components to the CL-810 10. HDMI/DVI Source Connections12. Progressive Component Video Connections DTV or Progressive Component YPbPr SourceDTV Source DVD Player, VCR Satellite Receiver Etc 13. Composite, S-Video and Component Video ConnectionsRS-232 Controller Connection16. Connecting the 12-Volt Trigger Output to Other Equipment AutoScope Lens Motor RearTurning on the Power Input voltage to the AutoScope lens motor must be betweenFocus Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments ZoomInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly18. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View GeometryFender Washer Adjusting the Lens Height Y Anamorphic Lens Set Screw Adjusting the Lens Height Y Geometry Installation Operation Selecting an Aspect Ratio Adjusting the PicturePicture Adjustment on Selecting Video MemoryUsing Picture-In-Picture/ Picture-By-Picture PIP/PBP Using the On-Screen MenusVideo InstallationSet Up Component1Enter or Picture AdjustmentMain Menu Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set toAspect Ratio You must enter a passcode in order to enter the Set Up menuInternational Color Consortium ICC is a group of imaging Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view Option Takes effect immediately you do not need to press EnterTo exit Shift controls in the Set Up menu see Set Up You select that menu after turning on the projectorOperation Remote Control Secondary Order to change the secondary IR codeIf your CL-810 Ultra installation includes an SDC-1 System ISF Calibration When you change a setting, save the change to a presetReset Picture Adjust This menu should be used by ISF-certified technicians onlyOperation Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionSymptom Maintenance and Troubleshooting Code Function Serial CommunicationsIs turned on or off Serial Communications Serial Commands Serial Communications Specifications CL-810 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsCL-810 Specifications CL-810 Dimensions CL-810 DimensionsCL-810 Ultra Dimensions CL-810 Ultra DimensionsSpecifications Page RUMA-011135 Rev 04-23-07 Runco CL-810 Owner’s Operating Manual

CL-810 / SDC-1, CL-810 ULTRA, CL-810 CINEWIDE specifications

The Runco CL-810 series projectors, including the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE, represent a pinnacle of home theater projection technology, designed to deliver stunning visual experiences for cinephiles and home entertainment enthusiasts alike. Each model within the CL-810 lineup integrates advanced features and state-of-the-art technologies to create immersive viewing experiences.

At the heart of the Runco CL-810 projectors is the proprietary DHD Digital High Definition video processing technology, which enhances source content to achieve unparalleled clarity and detail. This technology ensures optimal image scaling and color reproduction, delivering true-to-life visuals that captivate audiences. The projectors also utilize a high-performance light engine, capable of producing intense brightness and a wide color gamut for vibrant images.

The CL-810 ULTRA model boasts a 1080p resolution, which is ideal for showcasing high-definition content. It features advanced lens options, including motorized zoom and lens shift capabilities, allowing for flexibility in installation and optimal image alignment. This model's extensive connectivity options include HDMI inputs, ensuring compatibility with a wide variety of media sources.

The CL-810 CINEWIDE stands out for its unique CinemaScope capabilities, enabling a native 2.35:1 aspect ratio. This feature allows users to enjoy a cinematic experience without the need for additional lens systems or image cropping. The CINEWIDE version also offers adjustable aspect ratio settings, providing versatility for various film formats.

In addition to their remarkable image quality, the Runco CL-810 projectors emphasize quiet operation and energy efficiency. With advanced cooling systems, these projectors minimize noise for a distraction-free viewing environment. Furthermore, their energy-efficient design reduces power consumption while still providing exceptional performance.

The CL-810 series supports extensive customization options, allowing users to tailor their projection experience according to their preferences. With advanced calibration capabilities, these projectors can be fine-tuned to match specific room environments, ensuring optimal performance regardless of viewing conditions.

In summary, the Runco CL-810 series, featuring the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE models, delivers a premium home theater experience characterized by stunning resolution, versatile aspect ratios, and impressive color reproduction. With cutting-edge technology and customizable features, these projectors are designed to satisfy even the most discerning home cinema enthusiasts.
Top Page Image Contents