Runco CL-810 ULTRA, CL-810 CINEWIDE If your CL-810 Ultra installation includes an SDC-1 System

Page 73

Note

WARNING

Reset the Lamp Timer ONLY after you replace the lamp. Otherwise, the reported “Lamp Hours” will be inaccurate.

Do not exceed the recommended lamp life of 2000 hours. An old lamp becomes increasingly fragile and prone to sudden failure.

Fan Control: Select Fan Control from the Set Up Menu to control the operation of the projector’s cooling fan.

Mode: In most cases, the default Fan Control Mode (Auto Normal) will maintain the correct operating temperature. If the lamp frequently turns off due to overheating, or in certain high-altitude operating environments, you may need to change this setting to Auto Hi. Altitude or Manual.

Fan Speed: If you set the Fan Mode to Manual, select Fan Speed and use the on-screen slidebar to adjust the speed.

After changing either of these settings, press EXIT to return to the previous menu.

Screen Trigger Mode: Select Screen Trigger Mode from the Set Up menu to configure the 12-volt trigger output.

Set the Screen Trigger Mode to Normal if you want the trigger to activate when the projector is turned on (for instance, if the trigger is controlling a retractable screen).

Set the Screen Trigger Mode to AutoScope if you want the trigger to activate when the Cinema or Virtual Cinema aspect ratio is selected. Choose this setting if your CL-810 Ultra is equipped with the Runco CineWide with AutoScope system.

If your CL-810 Ultra installation includes an SDC-1 System

Note Expansion Device, you can also use the SDC-1 to trigger the AutoScope lens motor. Refer to the SDC-1 manual for more information.

Return to User OSD: To exit the Set Up menu, use the up- or down-arrow keys to highlight Return to User OSD and press ENTER.

To return to the Set Up menu, select it from the Main Menu, press ENTER twice, then press MENU on the remote control. (You do not need to re-enter the passcode.)

Runco CL-810 Series Owner’s Operating Manual

61

Image 73
Contents CL-810 Series Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Specifications Maintenance and TroubleshootingSerial Communications Table of Contents List of Figures List of Figures Xii About This Manual IntroductionRelated Documents Using This ManualFormat screen Description, Features and BenefitsOptional Accessories CL-810 Ultra Only Optional Accessories CL-810 and CL-810 UltraCL-810 at a Glance Controls and FunctionsCable Access Door Open to access connectors POWER/STANDBY LED Indicates power status as followsConnect only an SDC-1 to the R-Link input! Although CL-810 Rear PanelPower Input 100 to 240 VAC Connect the CL-810 to power here Comp 1 RCA connectorsVolt 250 mA Trigger Output 3.5-mm, mini phono jack Comp 2 / RGBCL-810 Remote Control CL-810 Remote ControlOn / OFF RVR Reflectance Volume RegulationSource Selection Buttons VID S-VideoMemory Preset Buttons Picture Adjustment Buttons BRT BrightnessContrast COL ColorSDC-1 System Expansion Device Picture-In-Picture PIP / Picture-By-Picture PBP ControlsMotorized Lens Controls Remote Control InstallationInstallation specialist Quick SetupInstallation Type Installation ConsiderationsAmbient Light Estimating Throw Distance 96x54-inch Throw Range Throw Ratio Inches, with Lens OptionLens Lens Only Anamorphic Minimum MaximumFloor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Lens Option CL-810 CL-810 Ultra Proteus Vertical and Horizontal Lens Shift LimitsOther Considerations Folded OpticsLens Motor Remove Projector Front Install Lens MotorFeet Mounting PlateAutoScope Lens Motor Installation Mounting the CL-810 Connections to Connector Panel AccessCL-810 System Expansion Device10. HDMI/DVI Source Connections Connecting Source Components to the CL-810DTV or Progressive Component YPbPr Source 12. Progressive Component Video Connections13. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver EtcConnection RS-232 ControllerAutoScope Lens Motor Rear 16. Connecting the 12-Volt Trigger Output to Other EquipmentInput voltage to the AutoScope lens motor must be between Turning on the PowerPrimary Lens Adjustments Changing the OSD Language Adjusting the Picture OrientationFocus ZoomIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic Lens18. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Installation Geometry Anamorphic Lens Top ViewFender Washer Adjusting the Lens Height Y Anamorphic Lens Set Screw Adjusting the Lens Height Y Geometry Installation Picture Adjustment on Selecting an Aspect Ratio Adjusting the PictureOperation Selecting Video MemoryUsing the On-Screen Menus Using Picture-In-Picture/ Picture-By-Picture PIP/PBPSet Up InstallationVideo Component1Main Menu Picture AdjustmentEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Below is set to Typical Test Pattern for Adjusting SharpnessInternational Color Consortium ICC is a group of imaging You must enter a passcode in order to enter the Set Up menuAspect Ratio Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view To exit Takes effect immediately you do not need to press EnterOption Shift controls in the Set Up menu see You select that menu after turning on the projector Set UpOperation Order to change the secondary IR code Remote Control SecondaryIf your CL-810 Ultra installation includes an SDC-1 System Reset Picture Adjust When you change a setting, save the change to a presetISF Calibration This menu should be used by ISF-certified technicians onlyOperation Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsSymptom Maintenance and Troubleshooting Is turned on or off Serial CommunicationsCode Function Serial Communications Serial Commands Serial Communications CL-810 Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsCL-810 Specifications CL-810 Dimensions CL-810 DimensionsCL-810 Ultra Dimensions CL-810 Ultra DimensionsSpecifications Page Runco CL-810 Owner’s Operating Manual RUMA-011135 Rev 04-23-07

CL-810 / SDC-1, CL-810 ULTRA, CL-810 CINEWIDE specifications

The Runco CL-810 series projectors, including the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE, represent a pinnacle of home theater projection technology, designed to deliver stunning visual experiences for cinephiles and home entertainment enthusiasts alike. Each model within the CL-810 lineup integrates advanced features and state-of-the-art technologies to create immersive viewing experiences.

At the heart of the Runco CL-810 projectors is the proprietary DHD Digital High Definition video processing technology, which enhances source content to achieve unparalleled clarity and detail. This technology ensures optimal image scaling and color reproduction, delivering true-to-life visuals that captivate audiences. The projectors also utilize a high-performance light engine, capable of producing intense brightness and a wide color gamut for vibrant images.

The CL-810 ULTRA model boasts a 1080p resolution, which is ideal for showcasing high-definition content. It features advanced lens options, including motorized zoom and lens shift capabilities, allowing for flexibility in installation and optimal image alignment. This model's extensive connectivity options include HDMI inputs, ensuring compatibility with a wide variety of media sources.

The CL-810 CINEWIDE stands out for its unique CinemaScope capabilities, enabling a native 2.35:1 aspect ratio. This feature allows users to enjoy a cinematic experience without the need for additional lens systems or image cropping. The CINEWIDE version also offers adjustable aspect ratio settings, providing versatility for various film formats.

In addition to their remarkable image quality, the Runco CL-810 projectors emphasize quiet operation and energy efficiency. With advanced cooling systems, these projectors minimize noise for a distraction-free viewing environment. Furthermore, their energy-efficient design reduces power consumption while still providing exceptional performance.

The CL-810 series supports extensive customization options, allowing users to tailor their projection experience according to their preferences. With advanced calibration capabilities, these projectors can be fine-tuned to match specific room environments, ensuring optimal performance regardless of viewing conditions.

In summary, the Runco CL-810 series, featuring the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE models, delivers a premium home theater experience characterized by stunning resolution, versatile aspect ratios, and impressive color reproduction. With cutting-edge technology and customizable features, these projectors are designed to satisfy even the most discerning home cinema enthusiasts.