Runco CL-810 CINEWIDE, CL-810 ULTRA, CL-810 / SDC-1 manual Adjusting the Horizontal X Lens Position

Page 48

Installation

Configure Lens Motor Trigger: CineWide with AutoScope maintains constant image height independent of the aspect ratio, while using the full display resolution of the projector. It accomplishes this by moving the anamorphic lens in front of the primary lens when widescreen material is being viewed. When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens moves out of the light path.

To configure the lens motor trigger on the CL-810 Ultra for proper AutoScope operation:

1.Press MENU on the remote control.

2.Select Service from the Main menu and press ENTER.

3.Use the number buttons on the remote to enter the Service menu passcode when prompted and press ENTER again. Then, press MENU on the remote control.

4.Select Screen Trigger Mode from the Service menu.

5.Set the Screen Trigger Mode to “AutoScope.” This enables the lens motor to move the anamorphic lens into position (in front of the primary lens) when the Cinema or Virtual Cinema aspect ratio is selected.

6.Select the Cinema or Virtual Cinema aspect ratio to move the anamorphic lens into position, if it isn’t already. To do this, press CINEMA or VCINE on the CL-810 remote control (Figure 2-4).

Adjusting the Horizontal (X) Lens Position:

1.Project a white field on the screen.

2.Loosen the Yaw/X-Adjustment Levers underneath the lens.

3.Slowly move the anamorphic lens into place (from right to left or vice versa) so that there are no shadows on either side of the screen:

Too Far Left

Correct position

Too Far Right

4.When the horizontal position is properly set, tighten the Yaw/X-Adjustment Levers to secure the lens in place.

36

Runco CL-810 Series Owner’s Operating Manual

Page 47 Page 49
Image 48
Page 47 Page 49
Contents CL-810 Series Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents List of Figures List of Figures Xii Introduction About This ManualUsing This Manual Related DocumentsDescription, Features and Benefits Format screenOptional Accessories CL-810 and CL-810 Ultra Optional Accessories CL-810 Ultra OnlyControls and Functions CL-810 at a GlancePOWER/STANDBY LED Indicates power status as follows Cable Access Door Open to access connectorsCL-810 Rear Panel Connect only an SDC-1 to the R-Link input! AlthoughComp 1 RCA connectors Power Input 100 to 240 VAC Connect the CL-810 to power hereVolt 250 mA Trigger Output 3.5-mm, mini phono jack Comp 2 / RGBCL-810 Remote Control CL-810 Remote ControlRVR Reflectance Volume Regulation On / OFFSource Selection Buttons VID S-VideoPicture Adjustment Buttons BRT Brightness Memory Preset ButtonsContrast COL ColorPicture-In-Picture PIP / Picture-By-Picture PBP Controls SDC-1 System Expansion DeviceMotorized Lens Controls Installation Remote ControlQuick Setup Installation specialistInstallation Considerations Installation TypeAmbient Light Estimating Throw Distance Throw Range Throw Ratio Inches, with Lens Option 96x54-inchLens Lens Only Anamorphic Minimum MaximumCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Lens Option CL-810 CL-810 Ultra ProteusFolded Optics Other ConsiderationsLens Motor Install Lens Motor Remove Projector FrontFeet Mounting PlateAutoScope Lens Motor Installation Mounting the CL-810 Connector Panel Access Connections toCL-810 System Expansion DeviceConnecting Source Components to the CL-810 10. HDMI/DVI Source Connections12. Progressive Component Video Connections DTV or Progressive Component YPbPr SourceDTV Source DVD Player, VCR Satellite Receiver Etc 13. Composite, S-Video and Component Video ConnectionsRS-232 Controller Connection16. Connecting the 12-Volt Trigger Output to Other Equipment AutoScope Lens Motor RearTurning on the Power Input voltage to the AutoScope lens motor must be betweenChanging the OSD Language Adjusting the Picture Orientation Primary Lens AdjustmentsFocus ZoomInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly18. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View GeometryFender Washer Adjusting the Lens Height Y Anamorphic Lens Set Screw Adjusting the Lens Height Y Geometry Installation Selecting an Aspect Ratio Adjusting the Picture Picture Adjustment onOperation Selecting Video MemoryUsing Picture-In-Picture/ Picture-By-Picture PIP/PBP Using the On-Screen MenusInstallation Set UpVideo Component1Picture Adjustment Main MenuEnter or Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set toYou must enter a passcode in order to enter the Set Up menu International Color Consortium ICC is a group of imagingAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view Takes effect immediately you do not need to press Enter To exitOption Shift controls in the Set Up menu see Set Up You select that menu after turning on the projectorOperation Remote Control Secondary Order to change the secondary IR codeIf your CL-810 Ultra installation includes an SDC-1 System When you change a setting, save the change to a preset Reset Picture AdjustISF Calibration This menu should be used by ISF-certified technicians onlyOperation Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionSymptom Maintenance and Troubleshooting Serial Communications Is turned on or offCode Function Serial Communications Serial Commands Serial Communications Specifications CL-810 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsCL-810 Specifications CL-810 Dimensions CL-810 DimensionsCL-810 Ultra Dimensions CL-810 Ultra DimensionsSpecifications Page RUMA-011135 Rev 04-23-07 Runco CL-810 Owner’s Operating Manual

CL-810 / SDC-1, CL-810 ULTRA, CL-810 CINEWIDE specifications

The Runco CL-810 series projectors, including the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE, represent a pinnacle of home theater projection technology, designed to deliver stunning visual experiences for cinephiles and home entertainment enthusiasts alike. Each model within the CL-810 lineup integrates advanced features and state-of-the-art technologies to create immersive viewing experiences.

At the heart of the Runco CL-810 projectors is the proprietary DHD Digital High Definition video processing technology, which enhances source content to achieve unparalleled clarity and detail. This technology ensures optimal image scaling and color reproduction, delivering true-to-life visuals that captivate audiences. The projectors also utilize a high-performance light engine, capable of producing intense brightness and a wide color gamut for vibrant images.

The CL-810 ULTRA model boasts a 1080p resolution, which is ideal for showcasing high-definition content. It features advanced lens options, including motorized zoom and lens shift capabilities, allowing for flexibility in installation and optimal image alignment. This model's extensive connectivity options include HDMI inputs, ensuring compatibility with a wide variety of media sources.

The CL-810 CINEWIDE stands out for its unique CinemaScope capabilities, enabling a native 2.35:1 aspect ratio. This feature allows users to enjoy a cinematic experience without the need for additional lens systems or image cropping. The CINEWIDE version also offers adjustable aspect ratio settings, providing versatility for various film formats.

In addition to their remarkable image quality, the Runco CL-810 projectors emphasize quiet operation and energy efficiency. With advanced cooling systems, these projectors minimize noise for a distraction-free viewing environment. Furthermore, their energy-efficient design reduces power consumption while still providing exceptional performance.

The CL-810 series supports extensive customization options, allowing users to tailor their projection experience according to their preferences. With advanced calibration capabilities, these projectors can be fine-tuned to match specific room environments, ensuring optimal performance regardless of viewing conditions.

In summary, the Runco CL-810 series, featuring the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE models, delivers a premium home theater experience characterized by stunning resolution, versatile aspect ratios, and impressive color reproduction. With cutting-edge technology and customizable features, these projectors are designed to satisfy even the most discerning home cinema enthusiasts.
Top Page Image Contents