Runco CL-810 / SDC-1, CL-810 CINEWIDE, CL-810 ULTRA manual Operation

Page 71

Operation

•H Threshold/V Threshold/Chroma Threshold: Set these to +11 or higher to activate the enhancement controls described above. Generally, the higher the threshold, the more noticeable the enhancements you make will be.

RVR Adjust: Use the RVR Adjust control to increase or decrease the Reflectance Volume Regulation setting. RVR lets you control the aperture or iris size (the physical opening through the lens; similar to an “f-stop” on a camera). Doing so allows you to optimize brightness and contrast according to the amount of ambient light in the viewing area.

Use a higher setting for rooms with lots of ambient light. Use a lower setting for more “theater-like” viewing conditions (little or no ambient light).

Image Over Scan: Image Over Scan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area.

Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Over scan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area.

Use the on-screen slidebar to select the desired amount of over scan.

For HDTV, DVDs and other video sources, Image Over Scan is generally not necessary or desirable.

Image Shift: The Image Shift menu allows you to precisely center the image on the screen. (These controls are available only with a 480i source signal.)

•Horizontal: This control moves the image right or left within the area of available pixels.

•Vertical: This option moves the image up or down within the area of available pixels.

1. To adjust the image position with a 480p or higher-resolution

Note source, use the PC & HD Adjust controls in the Option menu, described on page 57.

2.The values shown represent where the approximate center of the image lies in relation to the total number of pixels available horizontally or vertically. This varies widely according to the signal; watch the image while adjusting.

Amplitude Adjust: The Amplitude Adjust menu allows you to fine-tune the curently-selected image aspect ratio by stretching it horizontally or vertically, in small increments. This can be useful if your projector is equipped with an anamorphic lens.

The Horizontal control adjusts the image width while keeping the height constant.

Similarly, the Vertical control adjusts the image height while keeping the width constant.

Horizontal Masking (CineWide CL-810 versions only): To achieve the proper image geometry with the secondary anamorphic lens, select Horizontal Masking from the Set Up menu. Then, use the or button to change the native aspect ratio of the display, in small increments.

Runco CL-810 Series Owner’s Operating Manual

59

Page 70 Page 72
Image 71
Page 70 Page 72
Contents CL-810 Series Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents List of Figures List of Figures Xii About This Manual IntroductionRelated Documents Using This ManualFormat screen Description, Features and BenefitsOptional Accessories CL-810 Ultra Only Optional Accessories CL-810 and CL-810 UltraCL-810 at a Glance Controls and FunctionsCable Access Door Open to access connectors POWER/STANDBY LED Indicates power status as followsConnect only an SDC-1 to the R-Link input! Although CL-810 Rear PanelComp 2 / RGB Comp 1 RCA connectorsPower Input 100 to 240 VAC Connect the CL-810 to power here Volt 250 mA Trigger Output 3.5-mm, mini phono jackCL-810 Remote Control CL-810 Remote ControlVID S-Video RVR Reflectance Volume RegulationOn / OFF Source Selection ButtonsCOL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons ContrastMotorized Lens Controls Picture-In-Picture PIP / Picture-By-Picture PBP ControlsSDC-1 System Expansion Device Remote Control InstallationInstallation specialist Quick SetupAmbient Light Installation ConsiderationsInstallation Type Estimating Throw Distance Lens Only Anamorphic Minimum Maximum Throw Range Throw Ratio Inches, with Lens Option96x54-inch LensPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example only Lens Option CL-810 CL-810 Ultra Proteus Vertical and Horizontal Lens Shift LimitsOther Considerations Folded OpticsLens Motor Mounting Plate Install Lens MotorRemove Projector Front FeetAutoScope Lens Motor Installation Mounting the CL-810 System Expansion Device Connector Panel AccessConnections to CL-81010. HDMI/DVI Source Connections Connecting Source Components to the CL-810DTV or Progressive Component YPbPr Source 12. Progressive Component Video Connections13. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver EtcConnection RS-232 ControllerAutoScope Lens Motor Rear 16. Connecting the 12-Volt Trigger Output to Other EquipmentInput voltage to the AutoScope lens motor must be between Turning on the PowerZoom Changing the OSD Language Adjusting the Picture OrientationPrimary Lens Adjustments FocusIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic Lens18. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Installation Geometry Anamorphic Lens Top ViewFender Washer Adjusting the Lens Height Y Anamorphic Lens Set Screw Adjusting the Lens Height Y Geometry Installation Selecting Video Memory Selecting an Aspect Ratio Adjusting the PicturePicture Adjustment on OperationUsing the On-Screen Menus Using Picture-In-Picture/ Picture-By-Picture PIP/PBPComponent1 InstallationSet Up VideoEnter or Picture AdjustmentMain Menu Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Below is set to Typical Test Pattern for Adjusting SharpnessAspect Ratio You must enter a passcode in order to enter the Set Up menuInternational Color Consortium ICC is a group of imaging Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view Option Takes effect immediately you do not need to press EnterTo exit Shift controls in the Set Up menu see You select that menu after turning on the projector Set UpOperation Order to change the secondary IR code Remote Control SecondaryIf your CL-810 Ultra installation includes an SDC-1 System This menu should be used by ISF-certified technicians only When you change a setting, save the change to a presetReset Picture Adjust ISF CalibrationOperation Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsSymptom Maintenance and Troubleshooting Code Function Serial CommunicationsIs turned on or off Serial Communications Serial Commands Serial Communications CL-810 Specifications SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsCL-810 Specifications CL-810 Dimensions CL-810 DimensionsCL-810 Ultra Dimensions CL-810 Ultra DimensionsSpecifications Page Runco CL-810 Owner’s Operating Manual RUMA-011135 Rev 04-23-07

CL-810 / SDC-1, CL-810 ULTRA, CL-810 CINEWIDE specifications

The Runco CL-810 series projectors, including the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE, represent a pinnacle of home theater projection technology, designed to deliver stunning visual experiences for cinephiles and home entertainment enthusiasts alike. Each model within the CL-810 lineup integrates advanced features and state-of-the-art technologies to create immersive viewing experiences.

At the heart of the Runco CL-810 projectors is the proprietary DHD Digital High Definition video processing technology, which enhances source content to achieve unparalleled clarity and detail. This technology ensures optimal image scaling and color reproduction, delivering true-to-life visuals that captivate audiences. The projectors also utilize a high-performance light engine, capable of producing intense brightness and a wide color gamut for vibrant images.

The CL-810 ULTRA model boasts a 1080p resolution, which is ideal for showcasing high-definition content. It features advanced lens options, including motorized zoom and lens shift capabilities, allowing for flexibility in installation and optimal image alignment. This model's extensive connectivity options include HDMI inputs, ensuring compatibility with a wide variety of media sources.

The CL-810 CINEWIDE stands out for its unique CinemaScope capabilities, enabling a native 2.35:1 aspect ratio. This feature allows users to enjoy a cinematic experience without the need for additional lens systems or image cropping. The CINEWIDE version also offers adjustable aspect ratio settings, providing versatility for various film formats.

In addition to their remarkable image quality, the Runco CL-810 projectors emphasize quiet operation and energy efficiency. With advanced cooling systems, these projectors minimize noise for a distraction-free viewing environment. Furthermore, their energy-efficient design reduces power consumption while still providing exceptional performance.

The CL-810 series supports extensive customization options, allowing users to tailor their projection experience according to their preferences. With advanced calibration capabilities, these projectors can be fine-tuned to match specific room environments, ensuring optimal performance regardless of viewing conditions.

In summary, the Runco CL-810 series, featuring the SDC-1, CL-810 ULTRA, and CL-810 CINEWIDE models, delivers a premium home theater experience characterized by stunning resolution, versatile aspect ratios, and impressive color reproduction. With cutting-edge technology and customizable features, these projectors are designed to satisfy even the most discerning home cinema enthusiasts.
Top Page Image Contents