Runco 1080p manual Installing the Optional CineWide Lens Mount, AutoScope or Base Plate

Page 38

Installation

3.5

Installing the Optional CineWide Lens Mount

If you are installing a VX-44d/-55d with the optional CineWide or CineWide with AutoScope system, proceed as follows to install the anamorphic lens mounting assembly (stationary base plate or AutoScope lens motor).

1. Do not install the CineWide lens yet, only the mounting plate or

Note lens motor. You will install the CineWide lens after you install the projector and adjust the primary lens.

2.Some of the following steps are necessary only for CineWide with AutoScope installations.

	Remove Projector Front ➤	(Skip this step if you are installing a fixed CineWide anamorphic lens.)
	Feet (CineWide with	Place the projector upside down on a blanket or other soft surface. Loosen and remove
	AutoScope)
	AutoScope)	the two front feet on the projector.
		the two front feet on the projector.
	Install Anamorphic Lens ➤
	Motor (CineWide with	Note	The anamorphic lens mounting kit is partially pre-assembled at the
	AutoScope) or Base Plate	Note	factory – the AutoScope lens motor and lens mounting assemblies
	(fixed CineWide)		are both fully assembled.

CineWide with AutoScope: Line up the eight mounting holes on the lens motor housing with those on the bottom of the projector.

Secure the motor to the projector with the eight screws provided for this purpose.

Fixed CineWide: Line up the seven mounting holes on the lens mount base plate with those on the bottom of the projector, directly below the primary lens. Secure the base plate to the projector with the screws provided for this purpose.

26	Runco VX-44d/-55d Owner’s Operating Manual

Image 38

Contents VX-44d VX-55d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsRunco VX-44d/-55d Owner’s Operating Manual List of Figures Xii About This Manual Significance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories VX-44d/-55d at a Glance VX-44d/-55d Top/Rear/Front ViewVX-44d/-55d Input Panel Input 1 Rgbhv RemoteEthernet VX-44d/-55d Rear-Panel Keypad Down Button UP ButtonLeft Button Right ButtonIR Sensor DHD Controller Front PanelRunco Icon Vacuum Fluorescent DisplayMenu Button Composite Video Input DHD Controller Rear PanelOutputs 1. Hdmi OUT RS-232 Control Port Main Power SwitchComLink RS-232 Output Main AC FuseVX-44d/-55d Remote Control Unit DHD Controller/VX-44d/-55d Remote ControlLight IR Output IndicatorEnter ISF DAY CinemaISF Night CustInstallation Remote ControlInstallation specialist Quick SetupInstallation Overview Step Procedure For Details, Refer toInstallation Type Installation ConsiderationsProjector Installation Options Ambient LightVX-44d/-55d Lens Options and Throw Ratios Vertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewFixed CineWide Are both fully assembled Installing the Optional CineWide Lens MountAutoScope or Base Plate AutoScope stand used for floor-mounted projector Mounting VX-44d/-55dConnecting the VX-44d/-55d to the DHD Controller Connections to VX-44d/-55d and DHD ControllerController Connecting SourceComponents to the DHD Hdmi Connections See FigureDigital DTV RGB or Component Video Connections See Figure DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection Connecting 12-VoltRS-232 Controller Trigger Outputs toConnecting an External IR Receiver to the DHD Controller DHD Controller Rear PanelBuilt-in IR sensor on the DHD Controller is disabled Input voltage to the AutoScope lens motor must be betweenTurning on the Power Component SD Ntsc 480i AnamorphicVx44/55Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properlyHorizontal Position X Adjustment Configure Lens MotorAdjust the Anamorphic Trigger CineWide withInstallation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 16. TheaterMaster Remote Control for VX-44d/-55d MainTheaterMaster Remote Control FunctionsNavigating the Projector Menus Are disabledChannel Setup 4x3 nt PDigIDig Lbx ntAuto Setup Channel Edit NameTechnical Support Size and Position MenuAnamorphic lens in the light path, the aspect ratio is Installation Picture Quality Menu Adjust Pixel Tracking before Pixel PhaseValues shown represent where the approximate center Recommended see belowBack Porch There must be at least two consecutive white pixels present Uncheck this item before exiting this menuWhite Balance Pre Calibration 256 Auto Color EnableClipping Detector Color Enable Red 256To using LumaCal Installation MenuReadjust when absolutely necessary LumaCal lamp calibration takes approximately two minutesPower cycles Working With the Lamp Originally expected may no longer be possibleIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Using the On-Screen Menus OperationInput Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source Select Anamorphic to view Aspect Ratio SettingsRemote Aspect Ratio Control Description Key DVDs and HdtvCinema Picture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan ResolutionInput Position Information ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Should be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuCalibration You must enter a passcode to access the Service menu ServiceInput Names Restore Composite Video Component SD Button takes you from top to bottom in the left column, thenVertical Keystone Correction Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV ADC Bandwidth Auto YPbPr Input ResolutionUsed only for aspect ratio control and input selection AutoOperation Operation Lamp and Filter Replacement Removing the Lamp DoorRemoving the Lamp Lamp S/N Lamp Message Lamp Limit Lamp Mode Power Intensity147 RVRLens Replacement Removing the Primary LensSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Configure Lens Motor Code Description General VX-44d/-55d Error CodesError Codes Power and Cooling Code Description Lamp FailuresPanel Driver and Formatter Code Description Tipm Image ProcessorBuilt-In Keypad Code Description Miscellaneous Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax Aspect Ratio Commands Image Preset Commands Output Shift Commands Bkgnd Command Parameter Value Min/max Enter keyVX-44d/-55d Specifications VX-44d/-55d SpecificationsPower Requirements VX-44d Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsLimited Warranty Specifications are subject to change without noticeDHD Controller Specifications DHD Controller SpecificationsVX-44d/-55d Dimensions VX-44d/-55d Dimensions100 Runco VX-44d/-55d Owner’s Operating Manual Page RUMA-011195 Runco CL-810 Owner’s Operating Manual