Runco 1080p Home Theater Calibration Specifications, Industry-Standard Specifications, Dimensions

Page 108

Specifications

Table 7-1. VX-44d/-55d Specifications (continued)

Brightness and Contrast:

Cinema Standards Measurement System (CSMS)

 

Specifications

 

-

Brightness: 86.0 foot-Lamberts (fL) (VX-44d);

 

 

107.3 fL (VX-55d)

 

-

Contrast Ratio (variable, based on lens aperture setting):

 

 

233:1 - 285:1 (VX-44d);

 

 

229:1 - 279:1 (VX-55d)

 

These measurements are taken from the projector in a controlled,

 

home theater environment. All measurements are made to

 

ANSI/NAPM IT7.228-1997 specifications using the Photo Research

 

PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,

 

Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The

 

projector is calibrated to a color temperature of 6,500K and has a

 

minimum of 150 hours of usage.

 

The foot-Lambert (fL) is the unit of measurement used in commercial

 

movie theaters to express image brightness at the screen surface. The

 

Society of Motion Picture and Television Engineers (SMPTE) specifies

 

16 fL as the target image brightness for film-based projectors using an

 

open gate (without film in the projector). More importantly, today

 

SMPTE specifies 12 fL as the target image brightness in Digital

 

Cinema theaters. The foot-Lambert measurement is dependent on

 

screen size, screen gain and projector light output.

 

Home Theater Calibration Specifications

 

-

Light Output:

 

 

2180 ANSI Lumens (VX-44d);

 

 

3462 ANSI Lumens (VX-55d)

 

-

Contrast Ratio (variable, based on lens aperture setting):

 

 

233:1 - 285:1 (VX-44d);

 

 

229:1 - 279:1 (VX-55d)

 

These specifications are obtained by calibrating the projector as

 

described above for CSMS measurements.

 

Industry-Standard Specifications

 

-

Light Output:

 

 

4000 ANSI Lumens (VX-44d);

 

 

6000 ANSI Lumens (VX-55d);

 

-

Contrast Ratio (variable, based on lens aperture setting):

 

 

1500 - 2000:1

 

These are typical projector brightness and contrast specifications

 

found in most companies’ sales literature. Runco includes these

 

measurements in its literature to allow for direct comparison with other

 

manufacturers’ projectors. These measurements are typically taken at

 

9,000K to 13,000K to get expected performance data when the

 

projector is used in professional, commercial and industrial displays.

 

 

Power Requirements:

VX-44d:

 

100 to 240 VAC (auto-sensing), 50/60 Hz, 1,650 Watts

 

VX-55d:

 

200 to 240 VAC (auto-sensing), 50/60 Hz, 2,100 Watts

 

 

Operating Environment:

41°F to 95°F (5°C to 35°C), 20% to 80% humidity

 

(non-condensing)

 

 

Dimensions:

See Figure 7-1

 

 

Weight (without lens):

VX-44d:120 lbs. (54.43 kg)

 

VX-55d:130 lbs. (58.97 kg)

 

 

Regulatory Approvals:

Complies with FCC, CE C-Tick

 

 

 

96

Runco VX-44d/-55d Owner’s Operating Manual

Page 107 Page 109
Image 108
Page 107 Page 109
Contents VX-44d VX-55d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsRunco VX-44d/-55d Owner’s Operating Manual List of Figures Xii About This Manual Using This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories VX-44d/-55d at a Glance VX-44d/-55d Top/Rear/Front ViewVX-44d/-55d Input Panel Remote EthernetInput 1 Rgbhv VX-44d/-55d Rear-Panel Keypad UP Button Left ButtonDown Button Right ButtonDHD Controller Front Panel Runco IconIR Sensor Vacuum Fluorescent DisplayMenu Button DHD Controller Rear Panel Outputs 1. Hdmi OUTComposite Video Input Main Power Switch ComLink RS-232 OutputRS-232 Control Port Main AC FuseVX-44d/-55d Remote Control Unit DHD Controller/VX-44d/-55d Remote ControlIR Output Indicator EnterLight Cinema ISF NightISF DAY CustInstallation Remote ControlQuick Setup Installation OverviewInstallation specialist Step Procedure For Details, Refer toInstallation Considerations Projector Installation OptionsInstallation Type Ambient LightVX-44d/-55d Lens Options and Throw Ratios Ceiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewInstalling the Optional CineWide Lens Mount AutoScope or Base PlateFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector Mounting VX-44d/-55dConnecting the VX-44d/-55d to the DHD Controller Connections to VX-44d/-55d and DHD ControllerConnecting Source Components to the DHDController Hdmi Connections See FigureDigital DTV RGB or Component Video Connections See Figure DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs toConnecting an External IR Receiver to the DHD Controller DHD Controller Rear PanelBuilt-in IR sensor on the DHD Controller is disabled Input voltage to the AutoScope lens motor must be betweenTurning on the Power Component SD Ntsc 480i AnamorphicVx44/55Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properlyConfigure Lens Motor Adjust the AnamorphicHorizontal Position X Adjustment Trigger CineWide withInstallation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 16. TheaterMaster Remote Control for VX-44d/-55d MainTheaterMaster Remote Control FunctionsAre disabled Channel SetupNavigating the Projector Menus PDig IDig4x3 nt Lbx ntAuto Setup Channel Edit NameSize and Position Menu Anamorphic lens in the light path, the aspect ratio isTechnical Support Installation Adjust Pixel Tracking before Pixel Phase Values shown represent where the approximate centerPicture Quality Menu Recommended see belowBack Porch There must be at least two consecutive white pixels present Uncheck this item before exiting this menu256 Auto Color Enable Clipping Detector Color Enable RedWhite Balance Pre Calibration 256Installation Menu Readjust when absolutely necessaryTo using LumaCal LumaCal lamp calibration takes approximately two minutesPower cycles Working With the Lamp Originally expected may no longer be possibleIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Using the On-Screen Menus OperationISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Anamorphic to view DVDs and HdtvCinema Picture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation You must enter a passcode to access the Calibration menu CalibrationShould be used by ISF-certified technicians only You must enter a passcode to access the Service menu ServiceInput Names Restore Composite Video Component SD Button takes you from top to bottom in the left column, thenVertical Keystone Correction Keystone CorrectionADC Bandwidth Auto YPbPr Input Resolution Used only for aspect ratio control and input selectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV AutoOperation Operation Lamp and Filter Replacement Removing the Lamp DoorRemoving the Lamp Lamp Message Lamp Limit Lamp Mode Power Intensity 147Lamp S/N RVRLens Replacement Removing the Primary LensTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Configure Lens Motor VX-44d/-55d Error Codes Error CodesCode Description General Power and Cooling Code Description Lamp FailuresCode Description Tipm Image Processor Built-In KeypadPanel Driver and Formatter Code Description Miscellaneous RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Bkgnd Command Parameter Value Min/max Enter keyVX-44d/-55d Specifications VX-44d/-55d SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements VX-44d DimensionsLimited Warranty Specifications are subject to change without noticeDHD Controller Specifications DHD Controller SpecificationsVX-44d/-55d Dimensions VX-44d/-55d Dimensions100 Runco VX-44d/-55d Owner’s Operating Manual Page RUMA-011195 Runco CL-810 Owner’s Operating Manual
Top Page Image Contents