Manuals / Shindaiwa / Lawn and Garden / Trimmer

Shindaiwa T230 manual Assemble and Adjust the Throttle Cable, Assembly

Models: T230

1 24

Download 24 pages 54.22 Kb

Page 8

Image 8

Assembly

Throttle Linkage and Ignition Leads All Models

Assemble and Adjust

the Throttle Cable.

1. Insert the throttle-cable housing into the

notch on the fan cover, and clamp the

ground wire terminal between the fan

Red Wire	Black Ignition
	Black Ignition
	Wire

cover and the outer cable adjuster nut.

See Figure 13.

2. Tighten the two throttle cable adjuster

nuts.

IMPORTANT!

Adjust and tighten the cable nuts to allow approximately 1/4-inch free play at the throttle trigger.

3.Using finger pressure only, connect the black ignition wire from the cable tube to the red ignition wire on the powerhead. Wire routing must be as shown in the illustration with the black wire located away from the throttle cable and carburetor linkage.

4.Reinstall the engine cover and tighten the captive engine cover screw.

5.Reinstall the spark plug boot.

Cable Adjuster

Nuts

Ground

Wire

Ground Wire

Terminal

Figure 13

Reinstall the Spark

Plug Cap

CAUTION!

Routing of wiring must not interfere with throttle operation.

Page 8

Image 8

Shindaiwa T230 manual Assemble and Adjust the Throttle Cable, Assembly, Throttle Linkage and Ignition Leads All Models

Contents

SHINDAIWA OWNER’S/OPERATOR’S MANUAL T230 GRASS TRIMMER T230X GRASS TRIMMER C230 BRUSHCUTTERENGLISH T230 T230X C230Contents General Safety InstructionsIntroduction Attention StatementsMinimize the Risk of Fire General Safety Instructions The Properly Equipped OperatorStay Alert FEET Safety LabelsBe Aware of the Working Environment all units Unit Description SpecificationsPrior to Assembly Assembly Driveshaft/Powerhead All ModelsConnect the Outer Tube to the Powerhead HandleHandlebar C230 Throttle Linkage and Ignition Leads All ModelsAssemble the Handlebar Remove the Cylinder CoverAssemble and Adjust the Throttle Cable AssemblyRouting of wiring must not interfere with throttle operation Throttle Linkage and Ignition Leads All ModelsCutting Attachment Shield All Models Sub-Shield T230X and C230To Change Position of Line Cutter AssemblyInstall the Trimmer Head Trimmer Head C230/T230/T230XBlade C230/T230X Mount the BladeBlade C230/T230X continued Mixing FuelFilling the Fuel Tank The C230 Brushcutter should now be completely assembledWhen the Engine Starts Starting the EngineStopping the Engine 3. Cold Engine Only Set the choke lever to the CLOSED positionAdjusting Engine Idle Idle Speed AdjustmentOptional Accessories Using a BladeUsing a Grass Trimmer T230 Engine Operating SpeedsTrimming and Mowing Grass EdgingUsing A Brushcutter Blade C230/T230X Blade ThrustBrushcutter Handlebar Brushcutter HarnessGeneral Maintenance Daily Maintenance10-Hour Maintenance Muffler10/15-Hour Maintenance 50-Hour MaintenanceEvery 10 to 15 hours of operation Remove and clean the spark plug Every 50 hours of operation135-Hour Maintenance Long Term Storage Blade SharpeningMultiple-tooth Circular Blade Shindaiwa Tornado BladeTroubleshooting Guide What To CheckNO NO Possible CauseTroubleshooting Guide continued ADDITIONAL PROBLEMSSymptom Possible CauseFederal Emission Design And Defect Limited Warranty MAINTENANCE AND REPAIR REQUIREMENTSShindaiwa Corporation Utility And Lawn And Garden EnginesPage Specifications subject to change without notice Shindaiwa Inc 11975 S.W. Herman Rd Tualatin, Oregon 97062 USATelephone Shindaiwa Corporation Head Office 6-2-11, Ozuka-Nishi