Runco 1080p manual Working With the Lamp, Originally expected may no longer be possible

Page 70

Installation

3.13

Working With the Lamp

Lamp Adjust

Lamp Hours	147
Lamp S/N	123456789

1. Lamp Message

2.Lamp Limit 1000

3. Lamp Mode Power

4.Power 500

5.	Intensity	0
6.	RVR	3

7.Lamp History

8.Change Lamp

9.Reserved

Access the Lamp Adjust menu to:

•Choose a lamp mode for regulating power and light output.

•Change the optical aperture size.

•View information pertaining to past and present lamps.

•Record the lamp serial number in the projector’s memory.

Lamp Hours (read-only):Lamp Hours shows the number of hours logged on the current lamp. Whenever you record a new lamp serial number, the VX-44d/-55d automatically resets this value to zero and begins to log time for the new lamp.

Lamp S/N (read-only):Lamp S/N is the serial number recorded for the current lamp. When you install a new lamp and enter its serial number, the number appears here.

Lamp Message: Enter a check mark for Lamp Message to enable a warning message that appears upon power-up when the lamp has reached the specified lamp limit and should be replaced. Delete the check mark to prevent display of this message – instead, when your lamp expires, only the status display messages on the back of the projector will provide a visual warning to replace the lamp.

1. It is recommended that the Lamp Message check box remain

Note enabled.

2.When a lamp warning message appears, press EXIT to temporarily dismiss the warning. The message will continue to appear upon power-up until you install a new lamp.

Lamp Limit: Set Lamp Limit to the number of hours you expect to log on the current lamp before replacing it. This will trigger a lamp message on-screen (if enabled).

Note	1. If you change modes over the life of a lamp, the lamp limit you
	originally expected may no longer be possible.

2.Turning the lamp on and off reduces lamp life significantly, as do other factors.

3.It is recommended that Lamp Limit not exceed the expected lamp life, otherwise a lamp could become dangerously fragile with overuse.

58	Runco VX-44d/-55d Owner’s Operating Manual

Image 70

Contents VX-44d VX-55d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsRunco VX-44d/-55d Owner’s Operating Manual List of Figures Xii About This Manual Significance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories VX-44d/-55d at a Glance VX-44d/-55d Top/Rear/Front ViewVX-44d/-55d Input Panel Ethernet RemoteInput 1 Rgbhv VX-44d/-55d Rear-Panel Keypad Down Button UP ButtonLeft Button Right ButtonIR Sensor DHD Controller Front PanelRunco Icon Vacuum Fluorescent DisplayMenu Button Outputs 1. Hdmi OUT DHD Controller Rear PanelComposite Video Input RS-232 Control Port Main Power SwitchComLink RS-232 Output Main AC FuseVX-44d/-55d Remote Control Unit DHD Controller/VX-44d/-55d Remote ControlEnter IR Output IndicatorLight ISF DAY CinemaISF Night CustInstallation Remote ControlInstallation specialist Quick SetupInstallation Overview Step Procedure For Details, Refer toInstallation Type Installation ConsiderationsProjector Installation Options Ambient LightVX-44d/-55d Lens Options and Throw Ratios Vertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Vertical and Horizontal Lens Shift Limits Folded Optics Installing the Projection Lens Lens Assembly Front ViewAutoScope or Base Plate Installing the Optional CineWide Lens MountFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector Mounting VX-44d/-55dConnecting the VX-44d/-55d to the DHD Controller Connections to VX-44d/-55d and DHD ControllerController Connecting SourceComponents to the DHD Hdmi Connections See FigureDigital DTV RGB or Component Video Connections See Figure DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection Connecting 12-VoltRS-232 Controller Trigger Outputs toConnecting an External IR Receiver to the DHD Controller DHD Controller Rear PanelBuilt-in IR sensor on the DHD Controller is disabled Input voltage to the AutoScope lens motor must be betweenTurning on the Power Component SD Ntsc 480i AnamorphicVx44/55Adjusting the Picture Orientation Primary Lens Adjustments Focus Zoom Vertical and Horizontal Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properlyHorizontal Position X Adjustment Configure Lens MotorAdjust the Anamorphic Trigger CineWide withInstallation Anamorphic Lens Top View GeometryWrong Position Calibrating Projector Input 2 DVI 16. TheaterMaster Remote Control for VX-44d/-55d MainTheaterMaster Remote Control FunctionsChannel Setup Are disabledNavigating the Projector Menus 4x3 nt PDigIDig Lbx ntAuto Setup Channel Edit NameAnamorphic lens in the light path, the aspect ratio is Size and Position MenuTechnical Support Installation Picture Quality Menu Adjust Pixel Tracking before Pixel PhaseValues shown represent where the approximate center Recommended see belowBack Porch There must be at least two consecutive white pixels present Uncheck this item before exiting this menuWhite Balance Pre Calibration 256 Auto Color EnableClipping Detector Color Enable Red 256To using LumaCal Installation MenuReadjust when absolutely necessary LumaCal lamp calibration takes approximately two minutesPower cycles Working With the Lamp Originally expected may no longer be possibleIntensity value is not the actual lumen output, but rather a More easily maintained as the lamp ages Using the On-Screen Menus OperationInput Source ISF PresetsService Aspect RatioInput Source Main MenuAspect Ratio Select Anamorphic to view Aspect Ratio SettingsRemote Aspect Ratio Control Description Key DVDs and HdtvCinema Picture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Night ISF Day Custom Save Factory Default ISF PresetsInformation Calibration You must enter a passcode to access the Calibration menuShould be used by ISF-certified technicians only You must enter a passcode to access the Service menu ServiceInput Names Restore Composite Video Component SD Button takes you from top to bottom in the left column, thenVertical Keystone Correction Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV ADC Bandwidth Auto YPbPr Input ResolutionUsed only for aspect ratio control and input selection AutoOperation Operation Lamp and Filter Replacement Removing the Lamp DoorRemoving the Lamp Lamp S/N Lamp Message Lamp Limit Lamp Mode Power Intensity147 RVRLens Replacement Removing the Primary LensTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Configure Lens Motor Error Codes VX-44d/-55d Error CodesCode Description General Power and Cooling Code Description Lamp FailuresBuilt-In Keypad Code Description Tipm Image ProcessorPanel Driver and Formatter Code Description Miscellaneous Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Bkgnd Command Parameter Value Min/max Enter keyVX-44d/-55d Specifications VX-44d/-55d SpecificationsPower Requirements VX-44d Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsLimited Warranty Specifications are subject to change without noticeDHD Controller Specifications DHD Controller SpecificationsVX-44d/-55d Dimensions VX-44d/-55d Dimensions100 Runco VX-44d/-55d Owner’s Operating Manual Page RUMA-011195 Runco CL-810 Owner’s Operating Manual