AMD GA-MA69VM-S2 user manual I/O Back Panel Introduction

Page 17

1-6 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

COMA (Serial Port)

Connects to serial-based mouse or data processing devices.

VGA Port

Monitor can be connected to VGA port.

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.

Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

LAN Port

The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of 10/100/1000 Mbps.

Center/Subwoofer Speaker Out

The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected to Center/Subwoofer Speaker Out jack.

Surround Speaker Out (Rear Speaker Out)

The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can be connected to Surround Speaker Out (Rear Speaker Out) jack.

Side Speaker Out

The default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker Out jack.

Line In

The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out (Front Speaker Out)

The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surround speakers can be connected to Line Out (Front Speaker Out) jack.

English

- 17 -

Hardware Installation

Image 17
Contents GA-MA69VM-S2 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-MA69VM-S2 Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerALC888 Codec Feature SummaryBios Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction MIC Connectors IntroductionATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE IDE Connector Fpanel Front Panel Jumper Cdin CD In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector Faudio Front Audio Panel ConnectorCI Chassis Intrusion, Case Open PowerledClrcmos Clear Cmos Spdifio S/PDIF In/Out Connector TV TV Output ConnectorComb Comb Connector English Main Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example Bios Ver. D11„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 2/3 Master, Slave TimeIDE Channel 0 Master, Slave Drive a Floppy 3 Mode Support for Japan AreaHalt on MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check Boot Up Floppy SeekInternal Graphics Mode HDD S.M.A.R.T. CapabilityOnChip Sata Type OnChip IDE Channel0OnChip Sata Controller Onboard Audio Function Onboard LAN Boot ROMOnboard LAN Function OnChip USB ControllerOnboard Parallel Port Parallel Port ModeECP Mode Use DMA Power On By Keyboard Power On By MouseModem Ring Resume PME Event Wake UpAC Back Function KB Power on PasswordPower-On by Alarm PCI 2 IRQ Assignment PnP/PCI ConfigurationsPCI 1 IRQ Assignment System/CPU Warning Temperature Current System/CPU TemperatureCurrent VoltageV Vcore / DDR18V / +3.3V / +12V Current System/CPU FAN Speed RPMCPU Smart FAN Control Note CPU Smart FAN ModeLoad Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery2 Xpress Recovery2 IntroductionBoot from CD/DVD F9 Xpress Recovery2 System requirementsLimitations Main Screen of Xpress Recovery2Precautions Updating the Bios Flash Bios Method IntroductionMethod 1 Q-FlashTM Before UsePress Y to load Bios defaults Methods and steps Method 2 @BIOSTM UtilityEnglish Before you begin Installing Sata hard drives in your computerRAID Step Save and exit Bios Setup GA-M69VM-S2 Motherboard Main Menu Configuring RAID set in RAID BiosCreate Arrays Manually View Drive Assignments Delete an Array Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Hardware Installation Installation of TV Out Cable Optional DeviceIGX Configuration press Enter Center Method 2Through Software SettingsEnglish 6 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English English English English Taiwan Headquarters Contact UsGigabyte Global Service System