Analog Devices ADSST-EM-3040 specifications ADSST-SALEM-3T SPECIFICATIONS-ADSST-73360LAR

ADSST-SALEM-3T

SPECIFICATIONS—ADSST-73360LAR

(AVDD = 2.7 V to 3.6 V, DVDD = 2.7 V to 3.6 V, DGND = AGND = 0 V, fMCLK = 16.384 MHz, fSCLK = 8.192 MHz, fS = 8 kHz, TA = TMIN to TMAX1, unless otherwise noted.)

Table 6.

Parameter	Min	Typ	Max	Unit	Test Conditions
REFERENCE
REFCAP
Absolute Voltage, VREFCAP	1.08	1.2	1.32	V
REFCAP TC		50		ppm/°C	0.1 ∝F Capacitor Required from REFCAP to AGND2
REFOUT
Typical Output Impedance		130		Ω
Absolute Voltage, VREFOUT	1.08	1.2	1.32	V	Unloaded
Minimum Load Resistance	1			kΩ
Maximum Load Capacitance			100	pF
ADC SPECIFICATIONS
Maximum Input Range at VIN 2, 3		1.578		V p-p	Measured Differentially
		–2.85		dBm
Nominal Reference Level at VIN		1.0954		V p-p	Measured Differentially
(0 dBm0)
		–6.02		dBm
Absolute Gain
PGA = 0 dB	–1.3		+0.6	dB	1.0 kHz
PGA = 38 dB	–0.8		+0.8	dB	1.0 kHz
Signal to (Noise + Distortion)
PGA = 0 dB		76		dB	0 Hz to 4 kHz; fS = 8 kHz
PGA = 0 dB	71	76		dB	0 Hz to 2 kHz; fS = 8 kHz
					fIN = 60 kHz
PGA = 38 dB		58		dB	0 Hz to 4 kHz; fS = 64 kHz
Total Harmonic Distortion
PGA = 0 dB		–80	–71	dB	0 Hz to 2 kHz; fS = 8 kHz; fIN = 60 kHz
PGA = 38 dB		–64		dB	0 Hz to 2 kHz; fS = 64 kHz; fIN = 60 kHz
Intermodulation Distortion		–78		dB	PGA = 0 dB
Idle Channel Noise		–68		dB	PGA = 0 dB, fS = 64 kHz; SCLK = 16 MHz
Crosstalk ADC-to-ADC		–95		dB	ADC1 at Idle; ADC2 to ADC6 Input Signal: 60 Hz
DC Offset	–30		+30	mV	PGA = 0 dB
Power Supply Rejection		–55		dB	Input Signal Level at AVDD and DVDD Pins
					1.0 kHz, 100 mV p-p Sine Wave
Group Delay4, 5		25		∝s	64 kHz Output Sample Rate
		50		∝s	32 kHz Output Sample Rate
		95		∝s	16 kHz Output Sample Rate
		190		∝s	8 kHz Output Sample Rate
Input Resistance at VIN2, 4		25		kΩ6	DMCLK = 16.384 MHz
Phase Mismatch		0.15		Degrees	fIN = 1 kHz
		0.01		Degrees	fIN = 60 Hz

Rev. 0 Page 12 of 24