AMX VTM-D15/A Connecting the MultiMedia Components, VGA in DB-15 Connector Pinouts

Page 24

Installation and Wiring

1.Unscrew the PWR and GND wires on the terminal end of the PSN6.5 2-pin cable.

2.Pair the GND wires from the PSN6.5 and the Central Controller AXlink connectors together and insert them into the clamp position for GND on the TPI/3’s AXlink connector.

3.Tighten the clamp to secure the two GND wires.

4.Place the PWR wire from the PSN6.5 into the open clamp position for PWR on the TPI/3’s AXlink connector.

5.Tighten the clamp to secure the PWR wire.

Do not provide power to the TPI/3 at this time. Power is supplied after the entire system is wired together. Refer to the following section for powering procedures.

Using the VGA IN DB-15 (male) high-density connector

Connect the VTM-D15/A’s DB-15 (female) video connector to the VGA IN DB-15 (male) high-density connector on the rear panel of the touch panel. The following table below lists the VGA IN DB-15 connector pinouts.

VGA IN DB-15 Connector Pinouts

Pin

Signal

Function

 

 

 

 

 

1

Red

Red signals

 

 

 

 

 

2

Green

Green signals

 

 

 

 

 

3

Blue

Blue signals

 

 

 

 

 

4

N/A

Not used

 

 

 

 

 

5

GND

Signal Ground

5

 

 

 

 

6

RAGND

Red analog ground

 

 

 

 

 

7

GAGND

Green analog ground

 

 

 

 

 

8

BAGND

Blue analog ground

 

 

 

 

 

9

N/A

Not used

1

 

 

 

 

10

SAGND

Synchronization analog ground

 

 

 

 

 

11

N/A

Not used

 

 

 

 

 

12

N/A

Not used

 

 

 

 

 

13

HSYNC

Horizontal synchronization signal

 

 

 

 

 

14

VSYNC

Vertical synchronization signal

 

 

 

 

 

15

N/A

Not used

 

 

 

 

 

10

6

VGA DB-15 (male) connector

15

11

Connecting the MultiMedia Components

1.Connect the VGA signal cable from the rear of the VTM-D15/A panel to the Monitor Out port on the back of the TPI/3 (FIG. 19).

2.Connect the Touch Screen signal cable from the rear of the panel to the Mouse Port on the back of the TPI/3.

3.Connect the incoming video signal connector to either the Composite or S-Video connector ports on the TP3-VID card. Refer to the Setting up the AXB-TPI/3section on page 11 for input card installation instructions.

 

20

VTM-D15/A 15" MultiMedia Touch Panel Systems

 

 

 

Image 24
Contents VTM-D15/A AMX Limited Warranty and Disclaimer Table of Contents Upgrading the TPI/3 Firmware MultiMedia Touch Panel MultiMedia System ComponentsPower Adapter Power CordPin DB15 VGA Signal Cable Pin Mini Din to 9-pin DB9 Touch Panel Signal CableVTM-D15/A and VTM-D15/AB Specifications SpecificationsPSN6.5 Power Supply optional Floppy DiskIBM VGA VTM-D15/A and VTM-D15/AB Rear Components Rear component connection locations on the VTM-D15/AAXB-TPI/3 Specifications Dimensions HWDFront Panel Rear Panel Components SendCommands AXB-TPI/3 Components RgbhvVTM-D15/A Sample Configuration Pin captive-wireInstallation and Wiring Setting up the AXB-TPI/3Installing the input modules Removing input modulesSetting up the Panel Mounting the TPI/3 in an equipment rackTable Top Installation VTM-D15/A and D15/AS Installing the Table Top support bracketFixing holes on each side of pull-out flap Surface Mount Installation VTM-D15/AB and D15/ASB Connecting the cables on a VTM-D15/A table top panelInstalling the Surface Mount support bracket Surface Mounting Kit VTM-WMB contents Connecting the cables on a VTM-D15/AB surface mount panel Rear of VTM-D15/AB shown with attached VTM-WMB bracketWiring the AXB-TPI/3 Preparing captive wiresWiring guidelines Using the AXlink connector for data and powerConnecting the MultiMedia Components Using the VGA in DB-15 male high-density connectorVGA in DB-15 Connector Pinouts Pin Signal FunctionYour system is now connected and receiving power Installation and Wiring Configuration and Setup VTM-D15/A Startup and Setup ProceduresFront Panel buttons and indicators LEDs Setting Up Serial Communication from PC to the TPI/3 Setting Up Serial proceduresUsing Axcessx for serial communication COM Port Parameter Settings Using HyperTerminal for serial communicationParameter Setting Setting up the VTM-D15/A touch device Setting the Output Resolution Available ResolutionsResolution Refresh Rates Supported Touch DevicesSetting Up AXlink Communication from Master to the TPI/3 Setting Up AXlink proceduresCalibrating the Monitor Using Axcessx for AXlink communication Using HyperTerminal for AXlink communicationSetting up the VTM-D15/A touch device through AXlink Setting Up NetLinx Communication from PC to the TPI/3 Use the following command to set the mouse driverSet the Output resolution of the TPI/3 by entering Using NetLinx Studio for communication via an COM Port SendCommand 130,’calibrate’ Configuration and Setup Configuration Upgrading the TPI/3 FirmwareDownloading the Firmware Press F10 to exit the SoftROM program On Screen Display OSD Features On Screen Display OSD IconsOn Screen Display OSD Icons Exiting the OSD Selecting the Language of the OSDAdjusting Screen Brightness and Contrast Adjusting Display Performance Phase and ClockAdjusting Horizontal and Vertical Screen Position Selecting the Picture Color TemperatureAdjusting Display Color Red, Green, Blue Adjusting OSD Menu Parameters OSD Position and TimerAdjusting the Picture Sharpness Adjusting the OSD Timer settingAutomatic Contrast Adjustment Optimizing Picture Performance in DOS Graphic/TextReturning Recall to Factory Default Settings Troubleshooting Display TroubleshootingTroubleshooting Use these messages to address panel issues Troubleshooting VTM-D15/A 15 MultiMedia Touch Panel Systems AMX reserves
Related manuals
Manual 52 pages 47.78 Kb

VTM-D15/A specifications

The AMX VTM-D15/A is a next-generation armored vehicle designed for versatility and adaptability in modern combat scenarios. Developed to meet the evolving demands of modern military operations, it embodies advanced technologies and exceptional characteristics that make it a standout choice for armed forces worldwide.

At the heart of the AMX VTM-D15/A is its robust chassis, designed to withstand harsh terrains and explosive devices. The vehicle boasts a well-protected hull using advanced composite materials and ballistic plating, ensuring crew safety in hostile environments. It can be fitted with reactive armor systems that enhance protection against projectiles and anti-tank missiles.

The VTM-D15/A features a powerful engine that provides high mobility across various landscapes, capable of reaching speeds of up to 100 km/h on flat terrain. Its off-road capabilities are complemented by a sophisticated suspension system that allows for excellent maneuverability in rugged conditions. The vehicle is also equipped with all-terrain tires, further enhancing stability and traction.

One of the remarkable aspects of the AMX VTM-D15/A is its modular design that allows for quick configuration changes between various combat roles. This adaptability permits the integration of different weapon systems, including machine guns and anti-tank guided missiles, that can be rapidly mounted or dismounted as per operational requirements.

The vehicle's advanced battlefield management system improves situational awareness, allowing for real-time data sharing and communication with other units. It is equipped with state-of-the-art sensors and reconnaissance tools, ensuring that it can gather intelligence and operate effectively in diverse combat environments.

Moreover, the AMX VTM-D15/A emphasizes crew comfort and ergonomics, featuring a spacious interior designed for extended missions. The vehicle's climate control systems and noise-reduction technologies significantly enhance crew endurance and focus in prolonged operations.

In a world where military operations are increasingly dynamic, the AMX VTM-D15/A stands out as a versatile, powerful, and technologically advanced armored vehicle. Its combination of protection, mobility, and adaptability ensures that it can meet a wide array of mission requirements, making it a vital asset in modern military arsenals.