AMX VTM-D15/A Supported Touch Devices, Setting the Output Resolution, Available Resolutions

Page 31

Configuration and Setup

Supported Touch Devices

Touch Device

ID

 

 

No touch device

00

 

 

Microsoft serial mouse

01

 

 

2nd Microsoft Serial Mouse

02

(MX-MM Mobile Mouse®)

 

Dynapro® touch monitor

10

MicroTouch® touch monitor

11

Elo IntelliTouch® and VTM-D15/A

12

touch monitors

 

 

 

Elo AccuTouch® touch monitor

13

EZ Screen® touch monitor

15

External touch driver

FF

 

 

Mouse 12

This sets the TPI/3 touch device to the VTM-D15/A MultiMedia Touch Panel.

PRGM EX. 2

4.Type ?PAR again to verify the driver. The touch name should say Elo IntelliTouch.

Setting the Output Resolution

The output resolution for the monitor must be configured then calibrated.

Available Resolutions

Resolution

Refresh Rates

 

 

 

640 x 480

(VGA)

60 Hz, 72 Hz, 75 Hz, 85 Hz

 

 

 

800 x 600

(SVGA)

56, Hz, 60 Hz, 72 Hz, 75 Hz

 

 

1024 x 768 (XGA) (default)

60 Hz

 

 

 

To set the resolution:

1.Verify the connection of the output display monitor to the Monitor Out port at the rear of the TPI/3.

2.Use the following command in Terminal Emulator mode:

Resolution <hor>x<vert>:<refresh>

Allows you to set the resolution (horizontal/vertical) and refresh rate of the touch panel.

PRGM EX. 3

Refer to the Specifications table on page 3 for the horizontal, vertical, and refresh rates available for the output coming from the TPI/3.

Resolution 1024x768:60

This sets the TPI/3 to send a video signal at 1024 x 768 with a refresh rate of 60 Hz.

PRGM EX. 4

If the video is blurry, try a different refresh rate and/or resolution. Check the output device to verify you are using refresh rates and resolution settings are compatible with the device.

VTM-D15/A 15" MultiMedia Touch Panel Systems

27

 

 

 

 

Image 31
Contents VTM-D15/A AMX Limited Warranty and Disclaimer Table of Contents Upgrading the TPI/3 Firmware MultiMedia System Components MultiMedia Touch PanelPin Mini Din to 9-pin DB9 Touch Panel Signal Cable Power AdapterPower Cord Pin DB15 VGA Signal CableFloppy Disk VTM-D15/A and VTM-D15/AB SpecificationsSpecifications PSN6.5 Power Supply optionalIBM VGA Rear component connection locations on the VTM-D15/A VTM-D15/A and VTM-D15/AB Rear ComponentsDimensions HWD AXB-TPI/3 SpecificationsFront Panel Rear Panel Components SendCommands Rgbhv AXB-TPI/3 ComponentsPin captive-wire VTM-D15/A Sample ConfigurationRemoving input modules Installation and WiringSetting up the AXB-TPI/3 Installing the input modulesMounting the TPI/3 in an equipment rack Setting up the PanelInstalling the Table Top support bracket Table Top Installation VTM-D15/A and D15/ASFixing holes on each side of pull-out flap Connecting the cables on a VTM-D15/A table top panel Surface Mount Installation VTM-D15/AB and D15/ASBInstalling the Surface Mount support bracket Surface Mounting Kit VTM-WMB contents Rear of VTM-D15/AB shown with attached VTM-WMB bracket Connecting the cables on a VTM-D15/AB surface mount panelPreparing captive wires Wiring the AXB-TPI/3Using the AXlink connector for data and power Wiring guidelinesPin Signal Function Connecting the MultiMedia ComponentsUsing the VGA in DB-15 male high-density connector VGA in DB-15 Connector PinoutsYour system is now connected and receiving power Installation and Wiring VTM-D15/A Startup and Setup Procedures Configuration and SetupFront Panel buttons and indicators LEDs Setting Up Serial procedures Setting Up Serial Communication from PC to the TPI/3Using Axcessx for serial communication Using HyperTerminal for serial communication COM Port Parameter SettingsParameter Setting Setting up the VTM-D15/A touch device Supported Touch Devices Setting the Output ResolutionAvailable Resolutions Resolution Refresh RatesSetting Up AXlink procedures Setting Up AXlink Communication from Master to the TPI/3Calibrating the Monitor Using HyperTerminal for AXlink communication Using Axcessx for AXlink communicationSetting up the VTM-D15/A touch device through AXlink Use the following command to set the mouse driver Setting Up NetLinx Communication from PC to the TPI/3Set the Output resolution of the TPI/3 by entering Using NetLinx Studio for communication via an COM Port SendCommand 130,’calibrate’ Configuration and Setup Upgrading the TPI/3 Firmware ConfigurationDownloading the Firmware Press F10 to exit the SoftROM program On Screen Display OSD Icons On Screen Display OSD FeaturesOn Screen Display OSD Icons Selecting the Language of the OSD Exiting the OSDAdjusting Display Performance Phase and Clock Adjusting Screen Brightness and ContrastSelecting the Picture Color Temperature Adjusting Horizontal and Vertical Screen PositionAdjusting OSD Menu Parameters OSD Position and Timer Adjusting Display Color Red, Green, BlueAdjusting the OSD Timer setting Adjusting the Picture SharpnessOptimizing Picture Performance in DOS Graphic/Text Automatic Contrast AdjustmentReturning Recall to Factory Default Settings Display Troubleshooting TroubleshootingTroubleshooting Use these messages to address panel issues Troubleshooting VTM-D15/A 15 MultiMedia Touch Panel Systems AMX reserves
Related manuals
Manual 52 pages 47.78 Kb

VTM-D15/A specifications

The AMX VTM-D15/A is a next-generation armored vehicle designed for versatility and adaptability in modern combat scenarios. Developed to meet the evolving demands of modern military operations, it embodies advanced technologies and exceptional characteristics that make it a standout choice for armed forces worldwide.

At the heart of the AMX VTM-D15/A is its robust chassis, designed to withstand harsh terrains and explosive devices. The vehicle boasts a well-protected hull using advanced composite materials and ballistic plating, ensuring crew safety in hostile environments. It can be fitted with reactive armor systems that enhance protection against projectiles and anti-tank missiles.

The VTM-D15/A features a powerful engine that provides high mobility across various landscapes, capable of reaching speeds of up to 100 km/h on flat terrain. Its off-road capabilities are complemented by a sophisticated suspension system that allows for excellent maneuverability in rugged conditions. The vehicle is also equipped with all-terrain tires, further enhancing stability and traction.

One of the remarkable aspects of the AMX VTM-D15/A is its modular design that allows for quick configuration changes between various combat roles. This adaptability permits the integration of different weapon systems, including machine guns and anti-tank guided missiles, that can be rapidly mounted or dismounted as per operational requirements.

The vehicle's advanced battlefield management system improves situational awareness, allowing for real-time data sharing and communication with other units. It is equipped with state-of-the-art sensors and reconnaissance tools, ensuring that it can gather intelligence and operate effectively in diverse combat environments.

Moreover, the AMX VTM-D15/A emphasizes crew comfort and ergonomics, featuring a spacious interior designed for extended missions. The vehicle's climate control systems and noise-reduction technologies significantly enhance crew endurance and focus in prolonged operations.

In a world where military operations are increasingly dynamic, the AMX VTM-D15/A stands out as a versatile, powerful, and technologically advanced armored vehicle. Its combination of protection, mobility, and adaptability ensures that it can meet a wide array of mission requirements, making it a vital asset in modern military arsenals.