AMX AXB-IRS4 Configuration and Installation, Setting the Device DIP Switch, Position Value

Page 7

Configuration and Installation

Configuration and Installation

Setting the Device DIP Switch

The 8-position DEVICE DIP switch sets the AXlink identification number for the AXB-CAM. Make sure the device number matches the number assigned in the AXCESS software program.

When you set the first device number on the DEVICE DIP switch, the AXB-IRS4 automatically assigns the next three device numbers. For example, if you set the DEVICE DIP switch to 97 (1+32+64=97) as shown below, the AXB-IRS4 sets ports 1 through 4 as device numbers 97, 98, 99, and 100.

DEVICE

1 2 3 4 5 6 7 8 ON

FIG. 1 DEVICE DIP switch, set to 97

The following table describes the values on the DEVICE DIP switch.

Device DIP Switch Settings

Position

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

Value

1

2

4

8

16

32

64

128

 

 

 

 

 

 

 

 

 

To reset the AXB-IRS4 with a new DIP switch device number, disconnect and connect the AXlink or 12 VDC power connector on the AXB-IRS4.

If the AXB-IRS4 is wired for RS-232 communication, set all eight DIP switch positions to the off (up) position.

Setting the Carrier/BAUD DIP switch

The CARRIER/BAUD DIP switch sets the carrier signals and baud rates for the AXB-IRS4.

!DIP switch positions 1 through 4 set the carrier/NC signal option for ports 1 through 4.

!DIP switch position 5 is used for RS-232 or PCTouch mode.

!DIP switch positions 6 through 8 set the baud rate for RS-232 data communication. FIG. 2 shows the DIP switch positions.

CARRIER/BAUD

1

2

3

4

 

5

 

6

7

8

 

 

 

 

 

 

 

 

 

 

NC

Baud rate settings RS232/PCTouch mode select Carrier signal enable/disable

FIG. 2 CARRIER/BAUD DIP switch

AXB-IRS4 IR/Serial Interface (4 Ports)

3

 

 

 

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents AXB-IRS4 AMX Limited Warranty and Disclaimer Table of Contents Table of Contents Front panel components SpecificationsAXB-IRS4 Specifications Product InformationFront and rear views of the AXB-IRS4 Device DIP Switch Settings Configuration and InstallationSetting the Device DIP Switch Setting the Carrier/BAUD DIP switchRS-232 Baud Rate Settings Positions 1-4 Carrier signal enable/disablePosition 5 RS-232/PCTouch mode Positions 6-8 Baud rate settingAXlink communication Removing the circuit cardRS232 communication Preparing/connecting captive wires Wiring the AXB-IRS4Wiring Guidelines Wiring Guidelines at 125 mADB-9 Wiring Pinouts Using AXlink for data and powerUsing AXlink for data and a 12 VDC power supply Using the AXlink-to-DB-9 connector cable for a PC systemDB-25 Wiring Pinouts Using the AXlink-to-DB-25 connector cable for a PC systemSER Serial device wiring diagram Replacing the Lithium BatteryConnecting an IR device Connecting a serial deviceConfiguration and Installation Send Commands Channel Setting CommandsSend Commands Channel Setting CommandsSendcommand 2,CTON,10 Sendcommand 2, CH,18Sendcommand 2,CP,2 Sendcommand 2,CTOF,15Sendcommand IR1,XCH Sendcommand 1,SP,2Sendcommand IR1, XCH RS-232 Protocol Commands IR Output RS-232 Protocol CommandsRS-232 Protocol Commands IR Output RS-232 Protocol Commands Carrier RS-232 Protocol Commands Channel Pulse TimeRS-232 Protocol Commands Channel Pulse Time RS-232 Protocol Commands CarrierZAP!Dev RS-232 Protocol Commands MiscellaneousRS-232 Protocol Commands Miscellaneous ZapallProgramming AXB-IRS4 IR/Serial Interface 4 Ports AMX reserves
Top Page Image Contents