Altinex MAX Series manual SELnUx, InnOmmP, InnOmmUxP

Page 17

MATRIX SWITCHERS

This command allows control of each signal level independently. Once issued it is active until another [SELn] command is issued or the front panel is used to control the switcher.

When the front panel is used, the levels to be controlled are defined by the front panel selections. The front panel allows only 3 options of controlling channels; either AUDIO or VIDEO or AUDIO+VIDEO. It is not recommended to use the RS-232 control and the front panel at the same time to control different channels since front panel will override RS-232 controls.

The LEDs on the back of the unit display the status of a particular level. The RED LED indicates that this level is not enabled for controlling. The GREEN LED indicates that this level is currently enabled for controlling.

During the power ON the MAX automatically defaults to n=0 (Control all channels).

[SELnUx]

n = Same as above

This command works the same as above except for specific unit ID number. This command allows selection of levels (channels) on switchers that have been assigned unique unit ID numbers.

[InnOmm]

nn- input number 01 to 08 ( if input number 00 is used, that input is disconnected from the selected output)

mm- output number 01 to 04

This command connects Input to Output and switches them immediately.

For example, if you want to connect input 2 to output 1 and switch, the command to be issued will be: [I02O01]. Command [I00O01] will disconnect output 1 from any input.

[InnOmmP]

nn- input number 01 to 08 ( if input number 00 is used that input is disconnected from the selected output)

mm- output number 01 to 04

P - path

This command sets the switching path of connecting an input to an output but does not switch.

Through this command input to output connections are loaded (path is set), but not switched until [SW] or [SWUx] commands or a direct connection command of [IxxOmm] is sent.

For example, if you want to connect input 2 to output 1 and not switch it, the command to be issued will be: [I02O01P]

A typical sequence would look like this: [I01O02P][I04O01P][I08O03P][I05O04P][SW] or [I01O02P][I04O01P][I08O03P][I05O04].

[InnOmmUx]

xxInput number 01 to 08

yyOutput number 01 to 04

n Unit ID number 0-9, A-Z, a-z

This command allows any input to be connected immediately to any output on a MAX Switcher with a specific unit ID.

For example, if two MAX Switchers are connected to the same RS-232 port but have unit IDs set as 3 and 4, the following command can be issued to independently control each unit: [I02O04U3][[I04O01U4]. The first command connects input 2 to output 4 on the switcher with ID=3 and the second command connects input 4 to output 1 on the switcher with ID=4.

[InnOmmUxP]

xxInput number 01 to 08

yyOutput number 01 to 04

n Unit ID number 0-9, A-Z, a-z

This command is the same as [InnOmmUx], however the switching does not occur until [SWUx] or [SW] or direct connection command is issued. Through this path command, input to output connections are loaded, but not switched.

16

Image 17
Contents MAX Series Introduction Table of ContentsPRECAUTIONS/SAFETY Warnings Technical Specification About Your MAX Series Matrix SwitcherDiagram of FRONT/BACK Panel H & V SYNC, Composite Sync Back Panel ControlAudio Ports L&R RS-232 Ports 1&2Application Diagram Matrix Switchers Matrix Switchers Operation Installing Your SwitcherCONGRATULATIONS! YOU are Done Front Panel ControlBaud Rate Setting Saving Switcher Configuration in MemorySET Unit Sync Delay Function Connect Input to OutputIR Control Select SignalSET Unit ID Number Recall PRE-SET MemoryProgramming Commands ResetLock / Unlock Front Panel RS-232 Programming and ControlInnOmmS CODEnInnOmmA IkkOnnLUnit B SDELnnRset Control CommandsInnOmm SELnUxInnOmmP InnOmmUxSWUx DOxxyyzzkkDoxxyyzzkkUn SAVn FDBKnRCLn Projector ControlWired Infra-red Receiver IR-CONTROL ModeMAX Switcher Please noteCables and Accessories Troubleshooting Guide Altinex Policy Limited WarrantyReturn Policy Contact Information