Allied Telesis AT-IFS802SPOE manual Fault Relay Alarm, Sntp Configuration

Page 40

36

AT-IFS802SP/POE(W)-80 User Manual

 

 

6.9 Fault Relay Alarm

The Fault Relay Alarm function provides the Power Failure and Port Link Down/Broken detection. With both power input 1 and power input 2 installed and the check boxes of power 1/power 2 ticked, the FAULT LED indicator will then be possible to light up when any one of the power failures occurs. As for the Port Link Down/Broken detection, the FAULT LED indicator will light up when the port failure occurs; certainly the check box beside the port must be ticked first. Please refer to the segment of ‘Wiring the Fault Alarm Contact’ for the failure detection.

•Power Failure:Tick the check box to enable the function of lighting up the FAULT LED on the panel when power fails.

•Port Link Down/Broken:Tick the check box to enable the function of lighting up FAULT LED on the panel when Ports’ states are link down or broken.

Fault Relay Alarm interface

6.10 SNTP Configuration

SNTP (Simple NetworkTime Protocol) is a simplified version of NTP which is an Internet protocol used to synchronize the clocks of computers to some time reference. Because time usually just advances,the time on different node stations will be different.With the communicating programs running on those devices, it would cause time to jump forward and back, a non-desirable effect. Therefore, the switch provides comprehensive mechanisms to access national time and frequency dissemination services, organize the time-synchronization subnet and the local clock in each participating subnet peer.

Daylight saving time (DST) is the convention of advancing clocks so that afternoons have more daylight and mornings have less.Typically clocks are adjusted forward one hour near the start of spring and are adjusted backward in autumn.

Page 39 Page 41
Image 40
Page 39 Page 41
Contents AT-IFS802SP/POE Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3100 Hardware Features IntroductionCSMA/CD Software Features EMIPackage Contents Hardware Description Physical DimensionFront Panel Bottom View LED Indicators LEDHardware Installation Installation StepsDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP mini-GBIC combo portPage Network Application Ring ApplicationCoupling Ring Application Dual Homing Application Console Management Connecting to the Console PortPin Assignment Login in the Console Interface CLI ManagementCommands Level ExecSystem Login Web-Based ManagementAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration System configuration Dhcp ServerClient Entries Port and IP BindingsRestore Configuration Update FirmwareTftp Syslog Configuration Backup ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkState Activity tab Lacp disabled Aggregator InformationLacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based VlanVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning TreePort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority TypePort-based Priority COS Configuration Igmp ConfigurationTOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration802.1x System Configuration interface MAC Address Table Misc ConfigurationStatic MAC Address MAC Filtering All MAC Addresses MAC Address Table-Multicast FilteringMulticast Filtering interface Power over Ethernet Power Limit From Check it to decide the power limit method Save Configuration Factory DefaultSystem Reboot Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic RJ-45 Pin Assignments of POE TX+/VCC+ TX-/VCC+Appendix B-Command Sets System Commands SetPassword Low IPHigh IP Subnet maskPort Commands Set PortidDuplex full half 101001000autoState Enable DisableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Spanning Tree Commands Set ~61440Seconds Time secondsAutoTrueFalse Port PriorityTrueFalse QOS Commands Set Igmp Commands Set Multicast Filtering Commands Set Lldp Commands SetMac / Filter Table Commands Set IP-AddrSnmp Commands Set ExcludedIncluded View NameHost-address Port Mirroring Commands Set RXTXBoth802.1x Commands Set Port IDWords SecDisable reject Accept authorizeTftp Commands Set SystemLog, Smtp and Event Commands Set Fault Relay Alarm Commands Set EnabledisableSntp Commands Set Start time End timeMinute TimezoneControl Port Ring Commands SetDual Homing Port Legacy EnableDisable Port PortNumbers PoE Commands SetPort PortNumbers

AT-IFS802SPOE specifications

The Allied Telesis AT-IFS802SPOE is a robust and versatile solution designed for modern networking demands, particularly for enterprises requiring reliable connectivity in rugged environments. This device is part of Allied Telesis' commitment to delivering high-quality networking products with superior performance, making it an ideal choice for a range of applications.

One of the standout features of the AT-IFS802SPOE is its Power over Ethernet (PoE) capability. This allows the switch to deliver power directly through the Ethernet cable to connected devices such as IP cameras, VoIP phones, or wireless access points. With a total power budget supporting PoE+, the AT-IFS802SPOE simplifies installations by reducing the need for additional power sources, enhancing flexibility in system design while ensuring a clutter-free environment.

The AT-IFS802SPOE is designed with eight 10/100/1000 Mbps ports, offering extensive connectivity options for various devices. These Gigabit Ethernet ports ensure high-speed data transmission, significantly boosting network efficiency. The switch also supports auto-negotiation, allowing for dynamic adjustment of the speed and duplex settings for each connection. This adaptability contributes to seamless integration within diverse network environments.

In addition, the AT-IFS802SPOE features advanced management capabilities. With support for Layer 2 switching, VLAN (Virtual Local Area Network) configurations, and QoS (Quality of Service) functionalities, users can effectively manage traffic and prioritize critical applications. This characteristic is essential for organizations looking to optimize network performance and ensure that real-time applications such as video conferencing maintain high quality.

The switch is designed with durability in mind, featuring fanless operation for silent performance and a rugged form factor suitable for deployment in various environments, including industrial settings. Its compact size allows for easy installation in tight spaces, while the optional DIN rail mount makes it versatile for mounting in different configurations.

Moreover, Allied Telesis ensures that the AT-IFS802SPOE incorporates advanced security features to protect against unauthorized access and harmful attacks. With features such as MAC address filtering and port security, organizations can maintain network integrity while safeguarding their sensitive data.

In summary, the Allied Telesis AT-IFS802SPOE is a feature-rich, reliable switch that meets the challenges of contemporary networking. With its PoE capability, extensive port options, advanced management features, and rugged design, it is well-suited for any organization seeking to enhance their network infrastructure. Whether deployed in a small office or a complex industrial environment, the AT-IFS802SPOE delivers exceptional performance and reliability, making it an ideal choice for a wide range of networking needs.
Top Page Image Contents