Allied Telesis AT-IFS802SPOE manual Port Control

Page 45

AT-IFS802SP/POE(W)-80 User Manual

41

Port Statistics interface

6.14 Port Control

In Port control you can configure the settings of each port to control the connection parameters, and the status of each port is listed beneath.

•Port: Use the scroll bar and click on the port number to choose the port to be configured.

•State: Current port state.The port can be set to disable or enable mode. If the port state is set as ‘Disable’, it will not receive or transmit any packet.

•Negotiation: Auto and Force. Being set as Auto, the speed and duplex mode are negotiated automatically.When you set it as Force, you have to set the speed and duplex mode manually.

•Speed: It is available for selecting when the Negotiation column is set as Force. When the Negotiation column is set as Auto, this column is read-only.

•Duplex: It is available for selecting when the Negotiation column is set as Force. When the Negotiation column is set as Auto, this column is read-only.

•Flow Control: Whether or not the receiving node sends feedback to the sending node is determined by this item. When enabled, once the device exceeds the input data rate of another device, the receiving device will send a PAUSE frame which halts the transmission of the sender for a specified period of time.When disabled, the receiving device will drop the packet if too much to process.

•Security:When the Security selection is set as ‘On’, any access from the device which connects to this port will be blocked unless the MAC address of the device is included in the static MAC address table. See the segment of MAC Address Table—Static MAC Addresses.

•Click Apply to have the configuration take effect.

Page 44 Page 46
Image 45
Page 44 Page 46
Contents AT-IFS802SP/POE Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content 21.3 Appendix B-Command Sets100 Introduction Hardware FeaturesCSMA/CD EMI Software FeaturesPackage Contents Physical Dimension Hardware DescriptionFront Panel Bottom View LED LED IndicatorsInstallation Steps Hardware InstallationDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Gigabit Copper/SFP mini-GBIC combo port CablingPage Ring Application Network ApplicationCoupling Ring Application Dual Homing Application Connecting to the Console Port Console ManagementPin Assignment CLI Management Login in the Console InterfaceExec Commands LevelWeb-Based Management System LoginAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration Dhcp Server System configurationPort and IP Bindings Client EntriesUpdate Firmware Restore ConfigurationTftp Backup Configuration Syslog ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Sntp Configuration Fault Relay AlarmPage Page IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingState Activity tab Aggregator Information Lacp disabledLacp enabled Page State Activity Port Mirroring Rate Limiting Port-based Vlan Vlan configurationVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rapid Spanning Tree Rstp System ConfigurationPort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Policy and Priority Type QoS ConfigurationPort-based Priority Igmp Configuration COS ConfigurationTOS Configuration Ring Page Security-802.1X/Radius Configuration Lldp Configuration802.1x System Configuration interface Misc Configuration MAC Address TableStatic MAC Address MAC Filtering MAC Address Table-Multicast Filtering All MAC AddressesMulticast Filtering interface Power over Ethernet Power Limit From Check it to decide the power limit method Factory Default Save ConfigurationSystem Reboot Troubles shooting RJ-45 Pin Assignments Appendix A-RJ-45 Pin Assignment10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic TX+/VCC+ TX-/VCC+ RJ-45 Pin Assignments of POESystem Commands Set Appendix B-Command SetsLow IP PasswordHigh IP Subnet maskPortid Port Commands SetDuplex full half 101001000autoDisable State EnableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk ~61440 Spanning Tree Commands SetSeconds Time secondsPort Priority AutoTrueFalseTrueFalse QOS Commands Set Igmp Commands Set Lldp Commands Set Multicast Filtering Commands SetMac / Filter Table Commands Set IP-AddrSnmp Commands Set View Name ExcludedIncludedHost-address RXTXBoth Port Mirroring Commands SetPort ID 802.1x Commands SetWords SecAccept authorize Disable rejectTftp Commands Set SystemLog, Smtp and Event Commands Set Enabledisable Fault Relay Alarm Commands SetStart time End time Sntp Commands SetMinute TimezoneRing Commands Set Control PortDual Homing Port PoE Commands Set Legacy EnableDisable Port PortNumbersPort PortNumbers

AT-IFS802SPOE specifications

The Allied Telesis AT-IFS802SPOE is a robust and versatile solution designed for modern networking demands, particularly for enterprises requiring reliable connectivity in rugged environments. This device is part of Allied Telesis' commitment to delivering high-quality networking products with superior performance, making it an ideal choice for a range of applications.

One of the standout features of the AT-IFS802SPOE is its Power over Ethernet (PoE) capability. This allows the switch to deliver power directly through the Ethernet cable to connected devices such as IP cameras, VoIP phones, or wireless access points. With a total power budget supporting PoE+, the AT-IFS802SPOE simplifies installations by reducing the need for additional power sources, enhancing flexibility in system design while ensuring a clutter-free environment.

The AT-IFS802SPOE is designed with eight 10/100/1000 Mbps ports, offering extensive connectivity options for various devices. These Gigabit Ethernet ports ensure high-speed data transmission, significantly boosting network efficiency. The switch also supports auto-negotiation, allowing for dynamic adjustment of the speed and duplex settings for each connection. This adaptability contributes to seamless integration within diverse network environments.

In addition, the AT-IFS802SPOE features advanced management capabilities. With support for Layer 2 switching, VLAN (Virtual Local Area Network) configurations, and QoS (Quality of Service) functionalities, users can effectively manage traffic and prioritize critical applications. This characteristic is essential for organizations looking to optimize network performance and ensure that real-time applications such as video conferencing maintain high quality.

The switch is designed with durability in mind, featuring fanless operation for silent performance and a rugged form factor suitable for deployment in various environments, including industrial settings. Its compact size allows for easy installation in tight spaces, while the optional DIN rail mount makes it versatile for mounting in different configurations.

Moreover, Allied Telesis ensures that the AT-IFS802SPOE incorporates advanced security features to protect against unauthorized access and harmful attacks. With features such as MAC address filtering and port security, organizations can maintain network integrity while safeguarding their sensitive data.

In summary, the Allied Telesis AT-IFS802SPOE is a feature-rich, reliable switch that meets the challenges of contemporary networking. With its PoE capability, extensive port options, advanced management features, and rugged design, it is well-suited for any organization seeking to enhance their network infrastructure. Whether deployed in a small office or a complex industrial environment, the AT-IFS802SPOE delivers exceptional performance and reliability, making it an ideal choice for a wide range of networking needs.
Top Page Image Contents