Allied Telesis AT-IFS802SPOE manual Cabling, Gigabit Copper/SFP mini-GBIC combo port

Page 22

18

AT-IFS802SP/POE(W)-80 User Manual

 

 

3.6 Cabling

•Use four twisted-pair, Category 5e or above cabling for RJ-45 port connection.The cable between the switch and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long.

•Fiber segment using single-modeconnector type must use 9/125 µm single-mode fiber cable.

User can connect two devices in the distance up to 30km.

•Fiber segment using multi-modeconnector type must use 50 or 62.5/125 µm multi-mode fiber cable. User can connect two devices up to 2km distances.

•Gigabit Copper/SFP (mini-GBIC) combo port:

The Industrial switch has the auto-detected Giga port—Gigabit Copper/SFP combo ports.The Gigabit Copper (10/100/1000T) ports should use Category 5e or above UTP/STP cable for the connection up to 1000Mbps.The small form-factor pluggable (SFP) is a compact optical transceiver used in optical communications for both telecommunication and data communications.The SFP slots supporting dual mode can switch the connection speed between 100 and 1000Mbps.They are used for connecting to

the network segment with single or multi-mode fiber.You can choose the appropriate SFP transceiver to plug into the slots.Then use proper multi-mode or single-mode fiber according to the transceiver. With fiber optic, it transmits at speed up to 1000 Mbps and you can prevent noise interference from

the system.

[note]

The SFP/Copper Combo port can’t both work at the same time.The SFP port has the higher priority than copper port; if you insert the 1000M SFP transceiver (which has connected to the remote device via fiber cable) into the SFP port, the connection of the accompanying copper port will link down.

If you insert the 100M SFP transceiver into the SFP port even without a fiber connection to the remote, the connection of the accompanying copper port will link down immediately.

To connect the transceiver and LC cable, please follow the steps shown below:

First, insert the transceiver into the SFP module. Notice that the triangle mark is the bottom of the module.

Transceiver to the SFP module

Transceiver Inserted

Page 21 Page 23
Image 22
Page 21 Page 23
Contents AT-IFS802SP/POE Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3100 Hardware Features IntroductionCSMA/CD Software Features EMIPackage Contents Hardware Description Physical DimensionFront Panel Bottom View LED Indicators LEDHardware Installation Installation StepsDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP mini-GBIC combo portPage Network Application Ring ApplicationCoupling Ring Application Dual Homing Application Console Management Connecting to the Console PortPin Assignment Login in the Console Interface CLI ManagementCommands Level ExecAbout Web-based Management System LoginWeb-Based Management Preparing for Web ManagementSystem Information IP Configuration System configuration Dhcp ServerClient Entries Port and IP BindingsRestore Configuration Update FirmwareTftp Syslog Configuration Backup ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkState Activity tab Lacp disabled Aggregator InformationLacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based VlanVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning TreePort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority TypePort-based Priority COS Configuration Igmp ConfigurationTOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration802.1x System Configuration interface MAC Address Table Misc ConfigurationStatic MAC Address MAC Filtering All MAC Addresses MAC Address Table-Multicast FilteringMulticast Filtering interface Power over Ethernet Power Limit From Check it to decide the power limit method Save Configuration Factory DefaultSystem Reboot Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic RJ-45 Pin Assignments of POE TX+/VCC+ TX-/VCC+Appendix B-Command Sets System Commands SetHigh IP PasswordLow IP Subnet maskDuplex full half Port Commands SetPortid 101001000autoState Enable DisableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Seconds Spanning Tree Commands Set~61440 Time secondsAutoTrueFalse Port PriorityTrueFalse QOS Commands Set Igmp Commands Set Mac / Filter Table Commands Set Multicast Filtering Commands SetLldp Commands Set IP-AddrSnmp Commands Set ExcludedIncluded View NameHost-address Port Mirroring Commands Set RXTXBothWords 802.1x Commands SetPort ID SecDisable reject Accept authorizeTftp Commands Set SystemLog, Smtp and Event Commands Set Fault Relay Alarm Commands Set EnabledisableMinute Sntp Commands SetStart time End time TimezoneControl Port Ring Commands SetDual Homing Port Legacy EnableDisable Port PortNumbers PoE Commands SetPort PortNumbers

AT-IFS802SPOE specifications

The Allied Telesis AT-IFS802SPOE is a robust and versatile solution designed for modern networking demands, particularly for enterprises requiring reliable connectivity in rugged environments. This device is part of Allied Telesis' commitment to delivering high-quality networking products with superior performance, making it an ideal choice for a range of applications.

One of the standout features of the AT-IFS802SPOE is its Power over Ethernet (PoE) capability. This allows the switch to deliver power directly through the Ethernet cable to connected devices such as IP cameras, VoIP phones, or wireless access points. With a total power budget supporting PoE+, the AT-IFS802SPOE simplifies installations by reducing the need for additional power sources, enhancing flexibility in system design while ensuring a clutter-free environment.

The AT-IFS802SPOE is designed with eight 10/100/1000 Mbps ports, offering extensive connectivity options for various devices. These Gigabit Ethernet ports ensure high-speed data transmission, significantly boosting network efficiency. The switch also supports auto-negotiation, allowing for dynamic adjustment of the speed and duplex settings for each connection. This adaptability contributes to seamless integration within diverse network environments.

In addition, the AT-IFS802SPOE features advanced management capabilities. With support for Layer 2 switching, VLAN (Virtual Local Area Network) configurations, and QoS (Quality of Service) functionalities, users can effectively manage traffic and prioritize critical applications. This characteristic is essential for organizations looking to optimize network performance and ensure that real-time applications such as video conferencing maintain high quality.

The switch is designed with durability in mind, featuring fanless operation for silent performance and a rugged form factor suitable for deployment in various environments, including industrial settings. Its compact size allows for easy installation in tight spaces, while the optional DIN rail mount makes it versatile for mounting in different configurations.

Moreover, Allied Telesis ensures that the AT-IFS802SPOE incorporates advanced security features to protect against unauthorized access and harmful attacks. With features such as MAC address filtering and port security, organizations can maintain network integrity while safeguarding their sensitive data.

In summary, the Allied Telesis AT-IFS802SPOE is a feature-rich, reliable switch that meets the challenges of contemporary networking. With its PoE capability, extensive port options, advanced management features, and rugged design, it is well-suited for any organization seeking to enhance their network infrastructure. Whether deployed in a small office or a complex industrial environment, the AT-IFS802SPOE delivers exceptional performance and reliability, making it an ideal choice for a wide range of networking needs.
Top Page Image Contents