Allied Telesis AT-IFS802SPOE manual 802.1Q Configuration

Page 57

AT-IFS802SP/POE(W)-80 User Manual

53

802.1Q Configuration

• Pull down the selection item and focus on 802.1Q then press to set the VLAN Operation Mode in 802.1Q mode.

•Enable GVRP Protocol: GVRP (GARP VLAN Registration Protocol) is a protocol that facilitates control of virtual local area networks (VLANs) within a larger network. GVRP conforms to the IEEE 802.1Q specification, which defines a method of tagging frames with VLAN configuration data. This allows network devices to dynamically exchange VLAN configuration information with other devices. For example, having enabled GVRP on two switches, they are able to automatically exchange the information of their VLAN database.

Therefore, the user doesn’t need to manually configure whether the link is trunk or hybrid, the packets belonging to the same VLAN can communicate across switches. Tick this checkbox to enable GVRP protocol.This checkbox is available while the VLAN Operation Mode is in 802.1Q mode.

•Management VLAN ID: Only when the VLAN members, whose Untagged VID (PVID) equals to the value in this column, will have the permission to access the switch.The default value is ‘0’ that means this limit is not enabled (all members in different VLANs can access this switch).

•Select the port you want to configure.

•Link Type:There are 3 types of link type.

>Access Link: A segment which provides the link path for one or more stations to the VLAN-aware device.An Access Port (untagged port), connected to the access link, has an untagged VID (also called PVID). After an untagged frame gets into the access port, the switch will insert a four-byte tag in the frame. The contents of the last 12-bit of the tag is untagged VID.When this frame is sent out through any of the access port of the same PVID, the switch will remove the tag from the frame to recover it to what it was.Those ports of the same untagged VID are regarded as the same VLAN group members.

[note]

Because the access port doesn’t have an understanding of tagged frame, the column field of Tagged VID is not available.

>Trunk Link:A segment which provides the link path for one or moreVLAN-aware devices (switches). A Trunk Port, connected to the trunk link, has an understanding of tagged frame, which is used for the communication amongVLANs across switches.Which frames of the specified VIDs will be forwarded depends on the values filled in the Tagged VID column field. Please insert a comma between two VIDs.

[note]

1.A trunk port doesn’t insert tag into an untagged frame, and therefore the untagged VID column field is not available.

2.It’s not necessary to type ‘1’ in the tagged VID.The trunk port will forward the frames of VLAN 1.

3.The trunk port has to be connected to a trunk/hybrid port of the other switch. Both the tagged VID of the two ports have to be the same.

Page 56 Page 58
Image 57
Page 56 Page 58
Contents AT-IFS802SP/POE Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content 21.3 Appendix B-Command Sets100 Introduction Hardware FeaturesCSMA/CD EMI Software FeaturesPackage Contents Physical Dimension Hardware DescriptionFront Panel Bottom View LED LED IndicatorsInstallation Steps Hardware InstallationDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Gigabit Copper/SFP mini-GBIC combo port CablingPage Ring Application Network ApplicationCoupling Ring Application Dual Homing Application Connecting to the Console Port Console ManagementPin Assignment CLI Management Login in the Console InterfaceExec Commands LevelWeb-Based Management System LoginAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration Dhcp Server System configurationPort and IP Bindings Client EntriesUpdate Firmware Restore ConfigurationTftp Backup Configuration Syslog ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Sntp Configuration Fault Relay AlarmPage Page IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingState Activity tab Aggregator Information Lacp disabledLacp enabled Page State Activity Port Mirroring Rate Limiting Port-based Vlan Vlan configurationVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rapid Spanning Tree Rstp System ConfigurationPort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Policy and Priority Type QoS ConfigurationPort-based Priority Igmp Configuration COS ConfigurationTOS Configuration Ring Page Security-802.1X/Radius Configuration Lldp Configuration802.1x System Configuration interface Misc Configuration MAC Address TableStatic MAC Address MAC Filtering MAC Address Table-Multicast Filtering All MAC AddressesMulticast Filtering interface Power over Ethernet Power Limit From Check it to decide the power limit method Factory Default Save ConfigurationSystem Reboot Troubles shooting RJ-45 Pin Assignments Appendix A-RJ-45 Pin Assignment10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic TX+/VCC+ TX-/VCC+ RJ-45 Pin Assignments of POESystem Commands Set Appendix B-Command SetsLow IP PasswordHigh IP Subnet maskPortid Port Commands SetDuplex full half 101001000autoDisable State EnableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk ~61440 Spanning Tree Commands SetSeconds Time secondsPort Priority AutoTrueFalseTrueFalse QOS Commands Set Igmp Commands Set Lldp Commands Set Multicast Filtering Commands SetMac / Filter Table Commands Set IP-AddrSnmp Commands Set View Name ExcludedIncludedHost-address RXTXBoth Port Mirroring Commands SetPort ID 802.1x Commands SetWords SecAccept authorize Disable rejectTftp Commands Set SystemLog, Smtp and Event Commands Set Enabledisable Fault Relay Alarm Commands SetStart time End time Sntp Commands SetMinute TimezoneRing Commands Set Control PortDual Homing Port PoE Commands Set Legacy EnableDisable Port PortNumbersPort PortNumbers

AT-IFS802SPOE specifications

The Allied Telesis AT-IFS802SPOE is a robust and versatile solution designed for modern networking demands, particularly for enterprises requiring reliable connectivity in rugged environments. This device is part of Allied Telesis' commitment to delivering high-quality networking products with superior performance, making it an ideal choice for a range of applications.

One of the standout features of the AT-IFS802SPOE is its Power over Ethernet (PoE) capability. This allows the switch to deliver power directly through the Ethernet cable to connected devices such as IP cameras, VoIP phones, or wireless access points. With a total power budget supporting PoE+, the AT-IFS802SPOE simplifies installations by reducing the need for additional power sources, enhancing flexibility in system design while ensuring a clutter-free environment.

The AT-IFS802SPOE is designed with eight 10/100/1000 Mbps ports, offering extensive connectivity options for various devices. These Gigabit Ethernet ports ensure high-speed data transmission, significantly boosting network efficiency. The switch also supports auto-negotiation, allowing for dynamic adjustment of the speed and duplex settings for each connection. This adaptability contributes to seamless integration within diverse network environments.

In addition, the AT-IFS802SPOE features advanced management capabilities. With support for Layer 2 switching, VLAN (Virtual Local Area Network) configurations, and QoS (Quality of Service) functionalities, users can effectively manage traffic and prioritize critical applications. This characteristic is essential for organizations looking to optimize network performance and ensure that real-time applications such as video conferencing maintain high quality.

The switch is designed with durability in mind, featuring fanless operation for silent performance and a rugged form factor suitable for deployment in various environments, including industrial settings. Its compact size allows for easy installation in tight spaces, while the optional DIN rail mount makes it versatile for mounting in different configurations.

Moreover, Allied Telesis ensures that the AT-IFS802SPOE incorporates advanced security features to protect against unauthorized access and harmful attacks. With features such as MAC address filtering and port security, organizations can maintain network integrity while safeguarding their sensitive data.

In summary, the Allied Telesis AT-IFS802SPOE is a feature-rich, reliable switch that meets the challenges of contemporary networking. With its PoE capability, extensive port options, advanced management features, and rugged design, it is well-suited for any organization seeking to enhance their network infrastructure. Whether deployed in a small office or a complex industrial environment, the AT-IFS802SPOE delivers exceptional performance and reliability, making it an ideal choice for a wide range of networking needs.
Top Page Image Contents